Mani Fa

Пікірлер

@imelectrician6576 2 күн бұрын

Ok good

@imelectrician6576 2 күн бұрын

Waooww 😮

@hfc2191 9 күн бұрын

Thanks a lot , it was very helpful, i got a forgotten password and this solved it

@manifa59 9 күн бұрын

Glad to hear it.

@kenf2662 Ай бұрын

Hello, Very important what was your Spindle Motor Tuning numbers Steps Per, Velocity, Acceleration, Step Pulse, Dir Pulse

@thanhvannguyen307 Ай бұрын

Hello, can I enter the oemled code in the trigger to control the LED? But I measure the volts right at 24V and In1 (I set it up) and it does not output 24V regardless of whether I activate the signal or do not activate the signal. pls help me. tks 🥹

@AmirMahmoodKheirabadi Ай бұрын

سلام. من یک برد مثل شما و یک اینورتر متفاوت دارم. حدود یک ماه است که تلاش می کنم نحوه سیم بندی صحیح را پیدا کنم. اما موفق نمی شوم. البته در mach3 موتور روشن می شود. اما فرکانس تغییر سرعت ارسال نمی شود. براتون امکان داره من عکس سیم بندی روی اینورتر رو بفرستم و شما راهنمایی کنید که باید سیم های ACU و ACL رو به کدوم مورد وصل کنم ؟

@manifa59 Ай бұрын

سلام من در خدمتم ، بفرستید با هم چک میکنیم تلگرام هم میتونید پیام بدید @mani_fa

@AmirMahmoodKheirabadi Ай бұрын

@@manifa59 خیلی لطف می کنید. من ایمیل کردم براتون

@manifa59 Ай бұрын

اوکی

@apollo_guitars Ай бұрын

Tks for your vídeos! 👏 Try a upgrade in your driver step motor, tô DM 542, in my cnc is 100% better, than TB6600 and Tb6560...

@kawazukisoddbits2717 Ай бұрын

Personally for me, the video set up sequence was done far too fast for a non savvy computer person - like me! Without audio commentary it is difficult to follow! A list of hardware requirements would be a good idea as my Mach3 machining PC doesn't have WiFi nor does my workshop ! I'd actually just like to connect my pendant (like in the video banner) to my secondary parallel port but find instructions for that and associated code seems harder to find than 'chicken lip soup' !

@manifa59 Ай бұрын

Hi The title of the video shows that this video is about wifi control of your Mach3 , and this is a trigger to show friends that it is a way to control Mach3 over wifi via Android phone. For Handweel you can see this video: kzfaq.info/get/bejne/mtqEeJl0trjMlJc.htmlsi=9mX63zmWAycAKA7g About requirements suggestion, Good Idea, Thanks 👍 And for any problem up to solve it , you can be in touch in telegram: @mani_fa

@manifa59 Ай бұрын

Comments in on. It was off because of my mistake, sorry ❤

@JR-jq6ib Ай бұрын

THANKS

@JR-jq6ib Ай бұрын

IN YOUR PREVIOUS VIDEO, ABOUT MACHRODANT, THE LINK TO DOWNLOAD THE SERVER IS DEFECTIVE, CAN YOU PUT ANOTHER LINK, PLEASE.

@manifa59 Ай бұрын

Hi Machrodant Server file uploaded in description (in related video) Comments of Machrodant video are ON now👍

@3dmodelinghamid238 Ай бұрын

TNX A LOT FOR THAT JOG HANDLER? COULD you please GET WAIRING WITH SHEMAS... I NEED TO MAKE 1 SIMILAR... TNX AGAIN

@manifa59 Ай бұрын

Hi , full video coming soon in 1 or 2 days.

@3dmodelinghamid238 Ай бұрын

@@manifa59 tnx a lot, I like your videos

@manifa59 Ай бұрын

@@3dmodelinghamid238 Glad to hear it.❤

@luizmacena4623 Ай бұрын

Olá, parabéns pelo vídeo, foi a melhor ajuda que consegui. Como chama esse tipo de conector que você usou?

@manifa59 Ай бұрын

Hi glad to hear it. Connector name: IDC 10 pin connector www.amazon.com/Aexit-10-draads-IDC-connector-moederbord-lintkabel/dp/B07B7FWYRM

@cncrobotic5254 Ай бұрын

HI This video helped me a lot TOO, thank you! I APPRECIATED

@manifa59 Ай бұрын

Hi Glad to hear it

@agnaz1967 2 ай бұрын

Ein sehr gutes Video und sage mal Danke da ich wieder etwas Wissen mitnehmen durfte....

@manifa59 2 ай бұрын

you're welcome, glad to hear it. 🙏

@ekoharyanto8176 2 ай бұрын

is there a PCB layout?

@manifa59 2 ай бұрын

Hi No need for a PCB , just some wiring that I have shown in previous video maybe I should design one, Good idea, Thanks 👍

@ekoharyanto8176 2 ай бұрын

Nice

@manifa59 2 ай бұрын

Your welcome 🙏🙏

@AlexMoonXXI 2 ай бұрын

Hi! I also used Grbl 1.1, Grbl MEGA 5X, Mach3 + USB Controller. But all these options had drawbacks. But recently I found a type of controller that completely satisfies me: Orange Pi + LinuxCNC. At first I was skeptical about this decision. Now I have implemented this solution myself and am very pleased. It does not require a PC, but has an excellent GUI. It works great with MPG, laser, accurate height map and much more.

@ekoharyanto8176 2 ай бұрын

have you ever tried the grbl thing using STM32?

@manifa59 2 ай бұрын

Hi yes , I made a board with STM32 and it works great. here is the link: kzfaq.info/get/bejne/jLmWedhpneCbXas.html

@ekoharyanto8176 2 ай бұрын

@@manifa59 sori i meant GRBLHAL

@manifa59 2 ай бұрын

I did not test GRBLHall yet Maybe later to find a good PCB to make and also test it in many ways.

@ekoharyanto8176 2 ай бұрын

@@manifa59 thank you, I am very interested if you make a GRblhal based stm32 PCB with optocoupler protection

@Kr0NiCP4IN 2 ай бұрын

Can they be used as limit switch connections?

@manifa59 2 ай бұрын

Hi Let me try I guess you can use them , but I do not recommnd to use them for any uses like limit switch , these pins are not isolated with opto and have 5v voltage level to operate.

@goutampatra6200 2 ай бұрын

Ami warking shik bo sir

@manifa59 2 ай бұрын

Hi Great

@tasso6196 2 ай бұрын

This video helped me a lot, thank you!

@manifa59 2 ай бұрын

So glad to hear that

@tonyn9632 2 ай бұрын

Hello. I'm trying to connect the attached drive and spindle to the same Mach 3 board you have. but is not working. Maybe I programmed wrong. Can you advise? LCRHLCNC 110v Spindle Motor Kit，1.5Kw Square Air Cooled Spindle Motor 24000Rpm 400Hz，VFD Variable Frequency Drive，

@manifa59 2 ай бұрын

Hello Does it have any manual that I can look at?

@rafa_el9638 2 ай бұрын

Hey friend, did you solder the Arduino p4 to the Shield V3 terminal? I noticed that you are powering it through the P4 from Arduino

@manifa59 2 ай бұрын

Hi If you mean how I power the CNC shield through Arduino , I just solder VIN pin of CNC shield to positive terminal of Shield and now I can power both from power of Arduino.

@rafa_el9638 2 ай бұрын

@@manifa59 just positive pin or negative as well? I want do this because HC05 only works by powering the Arduino, both with 12V in this case. Thanks for answering me.

@manifa59 2 ай бұрын

Yes just positive pin. negative comes from pin headers and no need for wiring.

@rafa_el9638 2 ай бұрын

@@manifa59 In my case I already have a P4 on the CNC Shield V3, if I solder it this way it will power the Arduino in the same way, right? I'm powering a 12V fan and the Shield V3, in which case will I power the Arduino too?

@rafa_el9638 2 ай бұрын

Plug P4 is soldered with a wire and is on back case, then I feed it through the Shield V3, I will solder a wire to Arduino and test it.

@tytus894 3 ай бұрын

can you provide a link to the firmware

@tytus894 3 ай бұрын

jakie firmware?

@manifa59 3 ай бұрын

Hi you can download firmware from the link below: github.com/makerbase-mks/MKS-DLC32/tree/main/MKS-DLC32-main/firmware

@dormal4529 3 ай бұрын

Where to get a printed circuit board?

@AbolfazlKafchi 3 ай бұрын

سلام و عرض ادب استاد. ورژن مچتری شما چنده با چه لایسنسی

@manifa59 3 ай бұрын

سلام نسخه برنامه R3.043.066 هستش و لایسنس هم لایسنسی که همه استفاده میکنن

@martatrisna3775 3 ай бұрын

i think you missing the drill file on gerber zip, can you help to update the gerber, its a good work thank you for sharing your project

@sangukkim7868 3 ай бұрын

The video was very helpful I followed the settings, but each axis and speed change is reflected in mach3. But the off switch doesn't work. Even in the video, it is off, but the x-axis appears to be selected. How should I solve this?

@manifa59 3 ай бұрын

Hi off switch? you mean the side key? In some models the side key works as an on and off switch and some others use like my model. even after releasing the side key , the previous axis must be selected.

@sangukkim7868 3 ай бұрын

@@manifa59 My mpg is for the model without the side key. What I'm talking about is a rotary switch that selects the X, Y, and Z axes. Even if you leave this switch in the off position, the x-axis is still selected. I asked because I wasn't sure if I should use it in this state or if I had done something wrong with the settings.

@8thsinner 3 ай бұрын

Brilliant collection of resources, can't wait to play around with some once I get my current project finished. Thank you for sharing, and can't wait for more. Would you be able to convert any of these to vetric pro+ gadgets?

@manifa59 3 ай бұрын

You're welcome my friend I haven't tested it yet for vetric yet.

@8thsinner 3 ай бұрын

@@manifa59 No problem, you strike me as a bit of a coder so if anyone can figure it out that also uses it I'm guessing it would be you more than me. I am absolutely not a coder. But I've downloaded the vetric gadget maker files to use the add ons, some are better than others and I did find one spirograph gadget but not as cool as some of your finds.

@8thsinner 3 ай бұрын

Google won't let me download, says it is infected with a virus and only author can download. Looks cool and would love to try though if you can fix that issue.

@johnalex3023 3 ай бұрын

If the blue and black go to IN1 and DCM, does that mean I can’t use 24v on that side of the board for IN and OUT?

@manifa59 3 ай бұрын

Hi Blue and Blue/Black used for emergency stops and you can connect them to IN1 UpTo 4 , one lead goes to DCM and another lead goes to Input I didn't understand what you mean exactly

@johnalex3023 3 ай бұрын

I thought the inputs and outputs on that board get wired to a 24v supply

@manifa59 3 ай бұрын

@@johnalex3023 Aha I get it now. for these 8 pins they are not. they work with 5V instead of 24V and GND instead of DCM. remember, IN1-4 and OUT1-4 are opto isolated , therefore they can use 24v to operate.

@johnalex3023 3 ай бұрын

If I wire that estop that way, can I still use 24v on the other I/O?

@manifa59 3 ай бұрын

@@johnalex3023 Yes , for sure estop did not connect to those 8 pins and it is a separate key. for I/O 1-4 you can use 24v like before

@sachiramalinda8396 4 ай бұрын

Is this work x,y,z movements

@manifa59 4 ай бұрын

Hi you can use these pins for axis movement but not with this video configs , wait for the next video about jogging .

@sachiramalinda8396 4 ай бұрын

@@manifa59 okk

@insolence1335 4 ай бұрын

Amazing job. I have question is it possible to use this on proximity switches

@manifa59 4 ай бұрын

Thanks. In the manual, it mentioned that these pins can be used just for general inputs like buttons and also not suitable for limits. but if you want to use it for other purposes, let me know And I can test it for you.

@insolence1335 4 ай бұрын

@@manifa59 thanks for answer, it was all I needed to know

@sachiramalinda8396 4 ай бұрын

Is tis work x,y,z movements.

@Ggggggvvvvvvvvvvvtybffxgtdf 4 ай бұрын

سلام استاد من تمام مراحل روانجام دادم ولی انکودر کار نمیکنه همه قسمتها درست عمل میکنن

@manifa59 4 ай бұрын

سلام تنها قسمتی که فقط با یه تیک زدن باید کار کنه ، انکودر هستش که توی نکات گفته شده چند حالت داره : ۱. انکودر ۵ ولتی باید باشه نه ۱۲ ولتی ۲.امکان داره برد هم مشکل داشته باشه ۳. امکان داره سیم بندی انکودر متفاوت باشه برای تست انکودر بعد از تنظیم وارد تنظیمات افزونه rnrmotion بشید ، با چرخوندن انکودر باید قسمت A و B تیک دار بشه و بازی کنه حالت دوم تست هم با یه ماژول انکودر ساده آردوینو هستش که در حد تست میشه متوجه شد که بخش انکودر کار میکنه یا نه

@Ggggggvvvvvvvvvvvtybffxgtdf 4 ай бұрын

آخه تازه انکودر رو عوض کردم ممکنه مشکل از brain باشه

@manifa59 4 ай бұрын

انکودرتون ۵ ولته؟ نه کاری با brain نداریم ، اگر احتمال میدی خراب باشه ، مچ تری رو دوباره نصب کن خودم با اولین تنظیم به راحتی عملکرد انکودر رو دیدم و بعد رفتم سراغ بقیه تنظیمات (دقیقه ۱۳:۵۱) تنظیم خاصی نداره برای اینکه کار کنه ، ولی دیده ام که برد مچ تری قسمت هندویلش مشکل داشته باشه اگه برد دیگه ای هم دارید تست بگیرید دوباره باید بگم که با ماژول انکودر آردوینو تست هم گرفتم (فقط با تنظیمی که گفتم) و کار کرد

@Ggggggvvvvvvvvvvvtybffxgtdf 4 ай бұрын

اتفاقا دوباره نصب هم کردم مچتری رو فقط مونده برد که یه دونه دیگه بندازم بازم ممنون از لطفتون بله انکودرم ۵ ولتیه

@Ggggggvvvvvvvvvvvtybffxgtdf 4 ай бұрын

سلام مهندس جسا رتا سیستم عاملتون چیه و چند بیتی است

@yelshadayregasa4514 4 ай бұрын

hello there i like your work and thanks for the websites. i hv one question on this . how to change a SVG file to gcode? thanks

@manifa59 4 ай бұрын

Hi my friend Thanks A lot 🙏 To convert SVG to Gcode , you can simply use LaserGRBL software ,Also BachinDraw , LightBurn softwares can do it too

@yelshadayregasa4514 4 ай бұрын

ok thanks keep it up

@RodrigoLopez-zn2ir 5 ай бұрын

Hello. I am using the same bob and MPG. I did what you did, all connections, config etc. Everything is working except encoder. When i open Rnr motion card plugin window, i can see the MPG A and MPG B ticks. While i am rotating encoder they are blinking but Mach 3 is not counting at Settings (Alt-6) window so i can not move my axis. Can you help me please ?

@manifa59 5 ай бұрын

Hello If MPG A and MPG B ticks and while rotating they must change, for the test I use a rotary encoder module (for arduino) and it works somehow ok 1. The encoder must be 5v 2. If all settings are ok , check with another BOB let me know the result

@abdollahabdelallim2244 6 ай бұрын

what is the software and how you did it

@manifa59 6 ай бұрын

"Death to Sharpie" Processing software source

@o0Vion70o 6 ай бұрын

Hey, can you help me? I want to use the inputs for something else instead for a handweel. I wanna use the inputs for the endstops and e-Stop. I unse port 3 and pin 5-13 but nothing works 🙈

@manifa59 6 ай бұрын

Hi They can be use just for general inputs as a key or push button, so you can use them for for e-stop or run, pause , stop and so on , but not for endstops next video will be about these compabilities about adding more 8 push button.

@o0Vion70o 6 ай бұрын

@@manifa59 Nice to hear that! i let an Abo there so i dont miss that !

@reviewphimhay1104 7 ай бұрын

I followed you but it didn't work. Can you help me?

@manifa59 7 ай бұрын

Hi where is your problem exactly? @mani_fa (my telegram ID)

@reviewphimhay1104 7 ай бұрын

@@manifa59 Can I contact you via email? Because my telegram is not working

@abrahanaeoa733 7 ай бұрын

How did you configurate the button on/Off of the spindle? with OEM codes? In that case, can you tell me what codes control the spindle? Thank you

@manifa59 7 ай бұрын

Spindles will be on and off with gcode and configuration in output pins , I have a video to show you how to run spindle , wait for it ...

@pvsuryajaya1962 8 ай бұрын

please share circuit scematic of handwheel mpg, please open the box of handwheel mpg sir

@manifa59 8 ай бұрын

Hi I do not have it now but a schematic of wiring can be found here: cncyadak.com/wp-content/uploads/2020/09/Handwheel-MPG-CNC-MACH3-Siemens-GSK-4.jpg for any problem comment here

@riocncindonesia 9 ай бұрын

please share config and wirring sir

@manifa59 9 ай бұрын

Config and wiring Video is about to finish.

@petrkriza3654 9 ай бұрын

Hello.Thanks for your video. I set up my hand wheel according your video. I have one problem. X1 Its ok ( calibraton of MPG was Done). When I switch to X10 or X100, my motors doesn't go fluently.When I look at unit/mm there Is too hide numbers...nobody Is able to help.

@manifa59 9 ай бұрын

As I know if your velocity and acceleration is so high , your motor movement does not work well, change these values , and you can use other values for x10 and x100 too

@petrkriza3654 9 ай бұрын

@@manifa59but when I drive on my keyboard, motors go well (also when I use Shift - full Speed). IT is something like software don't akcept highest value of motors speeds.

@petrkriza3654 9 ай бұрын

...for specifycation i have handwheel without side button

@manifa59 9 ай бұрын

@@petrkriza3654 So let me check it

@tahaates5456 9 ай бұрын

Can you share BOM file? I couldnt see when I look your github page

@manifa59 9 ай бұрын

OKAY Let me make it ready

@tahaates5456 9 ай бұрын

@@manifa59Thanks. I’m waiting for your return

@HakkiOgrt 9 ай бұрын

You're awesome bro

@HakkiOgrt 9 ай бұрын

Thanks to you, I found a method.

@manifa59 9 ай бұрын

Your welcome man ,glad to hear it

@skurniyantomappadang 10 ай бұрын

can this board drive laser for cutting with electric power 80w? thanks

@manifa59 10 ай бұрын

Hi Base on documents of this board (v2.1) , it can operate upto 10w laser module and max 3A to 5A , 80W laser in max power uses 3.5A so it can be used in this board. If you have any doubt and if you want work safety , you can use separate power for laser like this: drive.google.com/file/d/12-9RIztQOyfhhU09ASBLlqhq8ZfQfxeT/view?usp=sharing with this schematic you can use any laser module with any power 😉

@necessary_tourist 10 ай бұрын

Trying to figure out myself how to get it work, but I'm not that good in mach3 configuration. Excited to see your next video!

@manifa59 4 ай бұрын

video will be release tonoght.

@jesperhansen8777 10 ай бұрын

Super helpful thank a English version will be most welcome

@manifa59 10 ай бұрын

So Glad to hear that ♥️

Ең жақсы KZfaq

Пікірлер