thanks so much for video . tool me 2 hour thanks again for video
@TBguitar2 күн бұрын
2016 CLA 250 4matic,,,,,, So the bottom plug is for draining, and the top for refill? I don't have jack stands, wondering if Joe's garage could handle this?
@paperandmedals83164 күн бұрын
Isn’t there a bolt and clip holding the CV axel into the transmission? This video is showing the 24 spindle transmission end of the axel just freely placed into the transmission with the steering knuckle side of the axel holding everything in place. That seems odd.
@VickyColorado14 күн бұрын
What about big circle and rear heater😅
@flex69yourmumАй бұрын
Dont think my 2016 CLA 45 AMG SB has had the rear diff oil changed, ever! Could this be what is causing a slight grinding / squeaking noise at low speeds from the rear left hand side.
@flex69yourmumАй бұрын
Very similar noise to that of a brake pad grind in my opinion.
@ac9812Ай бұрын
I use to be a mechanic. I work on my own car's. My suggestions is if you got spare time to play with it is not a hard job. It took me total of 3.5 hr including tuning and reset. Dealership quote me about 860AUD I brought all the parts for 648. Not included a 14mm hex and a dipstick 😮
@thereferee55472 ай бұрын
Genuine question how do you know how far you’re going down on the dip stick? Just as it doesn’t look like you put it all the way in? Thank you
@randomcar21902 ай бұрын
Correct... youw will hit the bottom of the pan with the measurement stick. It measure how much fluid you have from the bottom.
@DJ1702 ай бұрын
What is the link or part number for the dip stick ?
@yitroyasharahla54042 ай бұрын
Damn u paid $1500 for that lift?
@alsajfl02882 ай бұрын
I really enjoyed the video.
@phartusd672 ай бұрын
Thanks much for this straightforward video. This is my project this week and this is extremely helpful. I also like the approach - just the facts, no wannabe influencer vibe.
@canuckmc2 ай бұрын
So with everything that needs to come out, do a spark plug change while doing the front struts/sway bar links, water pump and save multiple hours later on :D
@CDEads3 ай бұрын
Hey you forgot your Loctite😊
@joejay28763 ай бұрын
10K mi. diff. fluid came out looking sort of good. 30k mi. came out like a sludge. I think I'm going to re-do it with my next engine oil change.
@tucobenedicto1093 ай бұрын
I put in a new oem on the passeger side. It was clicking up a hill and the boot was broken. Boot was replaced once!
@jamesanderson40143 ай бұрын
Nice job great video. If van or any vehicle has close to or 100,000 miles I would change upper intake gaskets, fuel injectors, coils and plugs one and done. I would use dealership parts or the same company that makes the dealership parts. The goal take that cover off as little as possible. I done the plugs first to we just keep learning.
@fmattrwd4 ай бұрын
Did you replace the seal
@hding984 ай бұрын
Did it work? Any damages?
@ruffytdog4 ай бұрын
No problems at all.
@user-mv4us8mi1l5 ай бұрын
Don’t they take 0w20 for oil?
@randomcar21905 ай бұрын
Not an oil expert here, but best to go with recommended 5-40. I'm guessing the 0-20 might be too thin for our car. 0-20 tend to be for the more fuel efficient type of cars.
Hi There! Are you by any chance located in the Bay Area, CA?
@dizzybuiltit91385 ай бұрын
Great video! Thanks
@user-kn4dr7kb2h6 ай бұрын
Sir~~ How to Change front Diff Fluid ????
@randomcar21905 ай бұрын
It's a transaxle type design. So the front axle is integrated with the transmission. Changing the transmission fluid will cover the front diff
@kezy26956 ай бұрын
Hey, do you know how to unplug brake hose from calipers? I want to unplug and paint the calipers, do not want to lose brake fluid
@fcfc27976 ай бұрын
For simplicity's sake, can anyone list out all the tools required for this maintenance? Much appreciated
@mikehawk1207 ай бұрын
Any difference for the 8G?
@mattboynton80787 ай бұрын
What is the sensor that you unhooked to remove the hoses from the intake at the beginning of the video 2:00
@rthavisin78197 ай бұрын
While measuring fluid level,is it necessary to run the engine?
@randomcar21905 ай бұрын
Yes
@rthavisin78195 ай бұрын
@@randomcar2190 thanks
@AEMBowers7 ай бұрын
Thanks for making this video! I have a 2019 GLA 45 AMG, and, according to the MBZ spec sheet, the correct fluid is 75W-85. Mine actually has the Dynamic Plus Package, which has a limited slip differential; again, although in a different column on the spec sheet, mine also calls for 75W-85. However, I really only see the 75W-90 LS (LS standing for limited slip) on the market around here (Bay Area, CA). I see from your video that you also used 75W-90 LS (by Mobile 1). Since you did the fluid change, have you learned anything more about the appropriateness of going with 75W-90 LS over 75W-85? Thanks in advance!
@ruffytdog7 ай бұрын
This is one of those "Best to do what I say, not what I do" situations. ;) Meaning, I'm saying it is definitely best to go with what the factory says. Their engineers know more than what I know about this. I think if weight is off by a little, it is probably ok. I think the most important thing is what additives are in the fluid, or shouldn't be in the fluid. I had no difference or problems with the Mobil w/ LS.... BUT... for my most recent diff fluid change, I did end up getting the OEM fluid online (you can probably get at a dealer). It's expensive, but you don't need much of it anyway. So the cost doesn't really add up too much. In short, I just recommend going w/ OEM. Or whoever makes the fluid for MB.
@faaygoo7 ай бұрын
What if my cracks aren’t deep can i just add the epoxy with the hardener and it will fix it ? or i have to sand it down and then add the epoxy and hardener?
@faaygoo7 ай бұрын
Hey i got small cracks on this same type of steering so i should wet sand with a 200 then a 1200 and then 3000 and they put polish compound that u put?
@chronocommander0078 ай бұрын
14 mm 12-point thinwall aocket, and better use a locking extension.
@MsNewbaby19 ай бұрын
Thank you very much for sharing. Well explained DIY. I placed a cover over intake openings to prevent anything from falling inside engine. . It took me 5 hours to do. You helped me save $900.00 Nicely done. 10-23-23
@fuhuxia94329 ай бұрын
More Sienna video please. I own the same car, it getting to the age that a lot of work need to be done.
@hmongyai9 ай бұрын
I’m done with Toyota buying different car😂
@benleach205510 ай бұрын
Where did you get the procedure documents??
@rodneysmith24710 ай бұрын
I'm curious how your van runs before and after the job or were you just following scheduled maintenance. I have a 2013 with almost 110,000mi very good 🎥 👍
@ehsanull10 ай бұрын
There is a bleeding if you open the engine cover
@mikelight200811 ай бұрын
Amazing! How many hours did it take you? Our shop plans to bill for 5 hours.
@NicoleMcFall Жыл бұрын
Do you know how to clean the hybrid intake on this vehicle?
@josenelsonelisan3769 Жыл бұрын
How do you reset the service reminder?
@tn2680 Жыл бұрын
I have a 2011 Honda Odyssey which takes about 20 minutes to replace all 6 spark plugs. Sister has a Sienna that needs plugs, not looking forward to this process. Great video. Thanks
@soroushfirouzi3572 Жыл бұрын
19:10 In this time that you were filling, how did you know the gearbox model ? How can i find mine?
@AEMBowers Жыл бұрын
Great video, my friend. Thank you!
@AEMBowers Жыл бұрын
Instead of having to remove the underbody panel every time to change the oil, it might be a good idea to purchase a Fumoto, or similar, oil drain valve. Some of them have a nipple that can be connected to a short segment of tube, thereby allowing for draining over the edge of the body panel. You also might need to use a Fumoto adapter/extension so that the valve protrudes out a bit. This is because the lever on the valve is on the side of the valve, and therefore might be obstructed by the well that the drain plug sits within.
@jasonLJ3 ай бұрын
could also make a little funnel ramp out of aluminum foil letting the oil spill off the side, or buy one of the reusable versions of the same
@rodneysmith247 Жыл бұрын
Remember replace overflow container coolant. Thank you for the video 👍
@computergeeksrepair Жыл бұрын
Is the cheap after market axle still OK? Im planing to as well so,
@ruffytdog Жыл бұрын
Aftermarket can be hit or miss. The one i got worked out fine. But maybe im lucky that i got the good one.
@junzhang8599 Жыл бұрын
应该顺便清洗一下节气门
@paulb5497 Жыл бұрын
How Can they do such a mess , no braiser ingener😢
@MFrappola Жыл бұрын
You need to reset the dash when you finish both sides or the parking brake will not work
@condor5635 Жыл бұрын
Don’t have to remove tie rod end! Just the two strut bolts