Chris Aaron

Пікірлер

@mikopiotrmazurek4048 2 күн бұрын

Great now they dont even work.. (fixed)

@mikopiotrmazurek4048 Күн бұрын

figured it out i did wiring wrong

@mppulidot 9 күн бұрын

I did a similar idea, i am using a piece of wine bottle cork (50%) in the bottom, a piece of soft pecil eraser (25%) and nothing else (25%) it feels fantastic for the money. The only cons is that the displacement is short now. Maybe the linear potentiometer (is the pressure progresive?) is better but expensive compared with this 25 Cents (usd)

@Jellybeantiger 11 күн бұрын

AXC pot is not very good. The metal clip keeps falling off when trying to install.

@sn0wwy809 Ай бұрын

it works! thank you

@SixfiveBowman 3 ай бұрын

that nut is a 7/16's

@koreylandia 3 ай бұрын

OK ok ok, can you show it working after the process? you know, just to make sure

@user-ts7ey2dm4h 4 ай бұрын

Now my throtle is stuck

@paolostrada93 4 ай бұрын

The MVH and GTEYE springs are made to the same spec afaik. The deadzone issue that you talk about actually affects PC users as well, because the deadzone is in the pedal firmware and can't be changed at all.

@francoispetitjean952 4 ай бұрын

Thx a lot for this video. Very well explained!

@F1WestCoast 5 ай бұрын

I'll be doing this for a friend until his FANATEC gear arrives...

@georgevasilopoulos5359 4 ай бұрын

Has it arrived yet or is fanatec continuing to have bad customer support.

@66lwmorgan 6 ай бұрын

This is the most detailed video showing this process, thank you for taking the time.

@Crediu 6 ай бұрын

what map is this

@R1LE7_yt 6 ай бұрын

Farming simulator needs a completely new vehicle physics system

@Crediu 6 ай бұрын

i agree

@coriscotupi 6 ай бұрын

If you took the trouble to remove the potentiometer, just replace it with a new one of the same resistance value. Theses things are dirt cheap (like US$1) , there's really no point in trying to disassemble & clean.

@Cesar-os5iv 6 ай бұрын

what are the specs of the g29 potentiometers?

@coriscotupi 6 ай бұрын

@@Cesar-os5iv Don't know specifically, but its easy enough to grab a multimeter and measure the resistance between the two outer contacts. It's probably in the 33K to 150k Range, linear taper.

@jaffmaster2294 6 ай бұрын

One could almost say it is worth disassembling and cleaning it if you cannot find or provide information on the correct replacement part.

@coriscotupi 6 ай бұрын

@@jaffmaster2294 It's easy enough to measure the pot's resistance value.

@66lwmorgan 6 ай бұрын

@@jaffmaster2294 I agree, if you don't know the specs or where to get one just take it apart, it seems fairly easy.

@brettnockolds4974 7 ай бұрын

Great video mate, but there’s no way I will be pulling the pedals that far apart…

@stfu7203 7 ай бұрын

My throttle pedal was flickering at max input between 95%-100%. After following your video, all is fixed. Thank you sir.

@daniell4711 7 ай бұрын

For those asking about measurements: it’s basically any spring that has an outside diameter that fits inside the main brake spring and can still move freely - you can eyeball this. The thing to pay attention to is wire thickness (thicker = stiffer) and how many coils it has (less coils = more stiff). From the video, it looks like the wire diameter is 3mm, which should be very close to the wire diameter of the main spring. Playing around with spring length, washers, and wire diameter will fine tune the brake feel. The washers themselves don’t add stiffness, it just changes the amount of force required for the inner spring to start to compress when load is applied while you brake. Hope that helps!

@denisbl_7191 8 ай бұрын

After doing this procedure my pedals are working great so far! I only have one small issue, my pedal wont go past 95% but its no big deal since I recalibrated it. I just have a quick question, is there any trick to reassemble the potentiometer fully centered so I get the full range of motion detected? I assembled it as shown in the video paying attention to detail but it seems kinda hard to get it 100% on the right position

@000BF000 9 ай бұрын

Anyone know if WD40 silicone lubricant can be used instead of the dielectric grease? Seems to be the same thing?

@ronsmith4325 5 ай бұрын

Don't use silicone, it will dry and cause issues.

@dghys 9 ай бұрын

Perfect video . Excellent explanation

@njdevil08105 10 ай бұрын

Hey chris anyway you can send me the diameter of the little spring?

@carlosmancuso 10 ай бұрын

To put it simply, you're great. You rock, man. My throttle is perfect now. It's funny that after fixing it, I remembered I had one spare potentiometer once I used a third-party load cell installed in the brake pedal.

@jackhutch3979 10 ай бұрын

Im trying to buy the stuff for this mod but i have some problems. I can only find a 50mm spring with 0.2 thickness so i was going to use original brake spring. Also i can only find a 6mm hex bolt will this work? My small spring i can find 1.5mm diameter And what washer size, will m4 work?

@nicholaslim3838 10 ай бұрын

Successful done the pot cleaning thanks to you. Thank you :)

@Scottdvz Жыл бұрын

Looking at the videos for the MVH Studios spring, you installed yours upside down. Similar to the GTEYE spring, the coils that are close together are on the bottom, away from the pedal.

@JimboP_ Жыл бұрын

I can’t get the white thing that sits below the spring back in

@CMDRKailoren Жыл бұрын

The wind noise on the video doesn't go away until 16:40. If you're listening with headphones only use the right one

@mgoles Жыл бұрын

Great race. Great consistency and attacks

@mgoles Жыл бұрын

That rig is no longer Logitech.

@wqxdv2145 Жыл бұрын

I opened the potentiometer cleaned it and it still doesn't work

@wqxdv2145 Жыл бұрын

@@chrisaaron8445 i fixed it btw, i said that 3 months ago

@02_andikaparikesit84 Жыл бұрын

I do the same and now it's always flicker, and I can't use the pedal, could u help me?

@wqxdv2145 Жыл бұрын

@@02_andikaparikesit84 fix the positions of those little things inside the potentiometer that touch the green disc, when they slide on it they send a signal and they might be in the wrong position, maybe too low or too high

@ciarannyland7398 Жыл бұрын

@@wqxdv2145 my throttle won’t go past 30% you think this could fix it?

@thomashimes2413 11 ай бұрын

@@ciarannyland7398mine does the same thing

@ardiantowibowo269 Жыл бұрын

Sir, could you tell me how to remove the original white damper on brake pedal, both red and black cylinder..?

@moodmusicytc Жыл бұрын

Pull them out with pliers

@jamestala2920 Жыл бұрын

This right here I tried but really the best solution is to just get the AXC sim brake mod and potentiometers since the pots are sealed on both of them meaning no cleaning is provided. I’m getting both of them this coming Friday so yeah. Everybody that owns the Logitech g29/g920/g923 should get this mod really the price for both is very affordable and you don’t have to clean it since once again the pots are sealed so no dust can’t go in really. Anyways yeah everybody from all over uses it and it’s been reviewed to be VERY GOOD which is why I ordered both recently so just go for it everybody!!!

@SU-jv2mg 8 ай бұрын

where can buy?

@Gdad-20 Жыл бұрын

Static electricity, attracts dust n all kinds of shit particle. Just look at the back of your TV's! So... Regular maintenance/cleaning is a must part of your racing. Use anti static cleaning materials and always... Dry Electrical contact cleaner. Not oil based lubricant, such as WD40 as oil, attracts more of what you are trying to avoid.

@jerzko Жыл бұрын

I sprayed wd40 on it and it works normally

@piopineda8503 Жыл бұрын

Where can i buy a replacement potentiometer?

@Hafizul12 Жыл бұрын

Id do this if I had a list of where to purchase these and weigh my options for time vs expense

@CaptainAd Жыл бұрын

great video, thank you.

@rainbowoof Жыл бұрын

How do you know which pedal was causing the issue? Do you clean al of them?

@Akira-kd6us Жыл бұрын

you check the input of each pedal and if any of them is flickering, it's time for you to clean the pots. Honestly, you should just clean all of them since you made the effort to take it apart. But that's IF you are confident in yourself that you can do it without braking it, if not just let someone else do it or spray the cleaners from the gap of those pots instead while pumping the pedals.

@playerzero0000 Жыл бұрын

What are those external shock/spring struts? You never said what the were or how they worked.

@simulationstimulation961 Жыл бұрын

Hey man, can I ask you for a favor?

@simulationstimulation961 Жыл бұрын

I have an idea that I want to test before buying this. I want to test that if you put the camera very close to the screen, on a level directly above the car dashboard (or in case of GTS anywhere), would it still work? I mean to put the camera nearly touching the TV in that spot, so that it doesn't pick up the overall tone of the image but only 1 spot. Do you think you can test that and make a video about it?

@CrucialArt Жыл бұрын

"look closely as i.." *fast forward x8* useless

@UbeydullahGungor Жыл бұрын

I don't suggest to tare everything apart if you don't have serious issue with your pedals. I had flickering on my break pedal. Seeing from a different video, I just opened the enclosing of the pedals and sprayed and cleaned the break potentiometer several times without unscrewing anything and it works perfectly. If it still doesn't work, you may go further. Other video: kzfaq.info/get/bejne/jLGXY81zyrbDnGw.html

@MrImpossiblyStupid Жыл бұрын

What’s the other video?

@UbeydullahGungor Жыл бұрын

@@MrImpossiblyStupid kzfaq.info/get/bejne/jLGXY81zyrbDnGw.html

@bobbybob3057 11 ай бұрын

@UbeydullahGungor Yeah, this video is for the people that already did that, and then the problem came back after lots of use. Cause that isn't the correct way of cleaning them and this one is, they last way more than that other "fix."