it would be better if logitech made closed pedals instead of leaving the whole shit open so they can farm dust and shit xD

My throttle pedal was flickering at max input between 95%-100%. After following your video, all is fixed. Thank you sir.

This is the most detailed video showing this process, thank you for taking the time.

To put it simply, you're great. You rock, man. My throttle is perfect now. It's funny that after fixing it, I remembered I had one spare potentiometer once I used a third-party load cell installed in the brake pedal.

Really good video, very well produced. Like many other people I have removed, dismantled and cleaned my G29 potentiometers several times, swapped them around, etc. This is the first time I have seen this CRC Di-Electric grease so I will get some and give it a try. I'm surprised your video hasn't caught people's attention. Thanks for putting it up.

Thank you man this video is perfect in every way...i really enjoy watching every moment of the video...great editing as well❤🙏

What a brilliant and descriptive video. Will definitely refer back to this when I need it. Thank you.

Successful done the pot cleaning thanks to you. Thank you :)

Thanks for putting this together - very helpful

Thx a lot for this video. Very well explained!

Perfect video . Excellent explanation

great video, thank you.

it works! thank you

After doing this procedure my pedals are working great so far! I only have one small issue, my pedal wont go past 95% but its no big deal since I recalibrated it. I just have a quick question, is there any trick to reassemble the potentiometer fully centered so I get the full range of motion detected? I assembled it as shown in the video paying attention to detail but it seems kinda hard to get it 100% on the right position

If you took the trouble to remove the potentiometer, just replace it with a new one of the same resistance value. Theses things are dirt cheap (like US$1) , there's really no point in trying to disassemble & clean.

I'm scared to open the potentionmeter bruh

I'm having trouble aligning the pedal cog with the pot cog, i put it right and it just jumps like 3 teeth up when I put the spring in, help?

Thank you so much sir ' .

Why does the dielectric grease is needed?

Where can i buy a replacement potentiometer?

OK ok ok, can you show it working after the process? you know, just to make sure

This right here I tried but really the best solution is to just get the AXC sim brake mod and potentiometers since the pots are sealed on both of them meaning no cleaning is provided. I’m getting both of them this coming Friday so yeah. Everybody that owns the Logitech g29/g920/g923 should get this mod really the price for both is very affordable and you don’t have to clean it since once again the pots are sealed so no dust can’t go in really. Anyways yeah everybody from all over uses it and it’s been reviewed to be VERY GOOD which is why I ordered both recently so just go for it everybody!!!

I can’t get the white thing that sits below the spring back in

Great video, I used dielectric grease and plugged it but didn't work, wiped it only to realize i plugged the pot back wrong (black colour red or something) Flickering absolutely gone now!

im having issues with the throttle, could i just swap the Potentiometer with the clutch? would it work the same? i dont mind if my clutch is bad

G29 pedals not working now. I watched your video & did my pedas just like you said but pretty sure I've got To much Grease on the all pots because I used my fingers..When I hooked it all back up after cleaning & over greasing. No contact, power, when trying to calibrate pedals.

Thanks for the video.. and about potentiometer.. can we replace it with the new one? I mean can we get the same spec potentio in the electric store? Terima kasih..

I don't suggest to tare everything apart if you don't have serious issue with your pedals. I had flickering on my break pedal. Seeing from a different video, I just opened the enclosing of the pedals and sprayed and cleaned the break potentiometer several times without unscrewing anything and it works perfectly. If it still doesn't work, you may go further. Other video: kzfaq.info/get/bejne/jLGXY81zyrbDnGw.html

Anyone know if WD40 silicone lubricant can be used instead of the dielectric grease? Seems to be the same thing?

How do you know which pedal was causing the issue? Do you clean al of them?

Is this why i have been experiencing throttle stutter in Assesto Corsa on my logitech g29?

I can't get those washers off without breaking the nut

Already done this, I've had it for more than 4 years. and after a week the brake comes back to the same problem.... I was thinking and swaping it with the clutch sensor, cos fuck, idk what else to do

Just THANKS ! my pedals now can handle 5k ir again!

CAN i use CRC maf sensor cleaning?

my potentiometer is burnt out on the inside, is there any way i can order a replacement?

Is the G27 made the same way?

Static electricity, attracts dust n all kinds of shit particle. Just look at the back of your TV's! So... Regular maintenance/cleaning is a must part of your racing. Use anti static cleaning materials and always... Dry Electrical contact cleaner. Not oil based lubricant, such as WD40 as oil, attracts more of what you are trying to avoid.

Now my throtle is stuck

Ma comprare dei potenziometri nuovi identici?

I'll be doing this for a friend until his FANATEC gear arrives...

Great video mate, but there’s no way I will be pulling the pedals that far apart…

can i use wd-40 for this?

"look closely as i.." *fast forward x8* useless

I opened the potentiometer cleaned it and it still doesn't work

I sprayed wd40 on it and it works normally