Nada se vè mas con esa mùsica fea, para que subes videos.
@victorjordan3876 Жыл бұрын
On my lanz surface cleaner the rotating rod falls out.oes the clip stop that
@berniemac8413 Жыл бұрын
Great video! Where did you get those pliers from?
@jeremyraeber4234 Жыл бұрын
Home Depot believe it or not.
@gabrieladjei5174 Жыл бұрын
Upon pushing the bearings back into the housing, he should have never hammer it back in. You just end up scratching the inside. Just apply little grease inside the bearing housing and outside the bearings itself and it should slide in like butter. Also apply small grease between the first bearing and the second as you pushed them done on the piston if you like to call it piston. It will work flawlessly. Thank me later
@CivilDefenceCanada2 жыл бұрын
I mean, if you're the person who bought it new, just make sure you register it and you get a free lifetime warranty, and they will send you a new tool to replace the faulty one.
@aaronorluck76322 жыл бұрын
Great video. 6302 bearing. For mine, I used an S6302-2RS, stainless with two rubber seals. $6 each (2 required) on Amazon.
@markread73333 жыл бұрын
Did you disconnect the plug? I must have missed that…🥴
@jeremyraeber42343 жыл бұрын
Let me think, I'll not get back to you on that. lol
@theantisimp82583 жыл бұрын
Fucking A+ bro I have a edou 20inch, this just made me me confident af, love it, KZfaq is the dad I never had
@jeremyraeber42343 жыл бұрын
Lmao
@ohiovalleysoftwashrestorat67602 ай бұрын
i have the edou 20 inch will these fit that size?
@andrewbutler77243 жыл бұрын
Good job. Very helpful.
@memphismania323 жыл бұрын
thank you....did yours lose power when it went bad
@jeremyraeber42343 жыл бұрын
It did . Then it froze.
@sandspritpark3 жыл бұрын
Deep groove bearings?
@jeremyraeber42343 жыл бұрын
Just a sealed ball bearing bearing.
@fendertree66243 жыл бұрын
What size are those bearings
@jeremyraeber42343 жыл бұрын
42mmx15mmx13mm
@ToolApc3113 жыл бұрын
What size torx screwdriver do you need
@jeremyraeber42343 жыл бұрын
25
@jeffheidenreich61314 жыл бұрын
What is the bearing number?
@HouseWashingRick4 жыл бұрын
Jeremy, the ring you pulled out at 2:10 do you know what size it is. I brought mine and no store around here in my area has one.
@jeremyraeber42344 жыл бұрын
I don't. Try going to Fastenal they have every size.
@HouseWashingRick4 жыл бұрын
@@jeremyraeber4234 ty bud
@HouseWashingRick4 жыл бұрын
Is this a Mi T M surface cleaner?? My beavis locking up on me on a job right now and I don't know how to fix it
@jeremyraeber42344 жыл бұрын
Yes it is.
@theginger11874 жыл бұрын
Forgot to empty the gas and went to do the part at 2:30... oof 😂
@jeremyraeber42343 жыл бұрын
Oh no, whatever is the world going to do?
@theginger11873 жыл бұрын
@@jeremyraeber4234 wasnt bad, not like it was a car gas tank or something lmao
@marsuttGoldgate4 жыл бұрын
Dude you forgot to hook up the throttle cable.
@johnnydough88413 жыл бұрын
I had to rewind a few times …thought I missed that step lol
@xxdeedee5 жыл бұрын
U didn't Evan grease It u wrongun
@jeremyraeber42345 жыл бұрын
That's because you don't grease sealed bearings. That's why they are called sealed.
@xxdeedee5 жыл бұрын
@@jeremyraeber4234 so they never get greased then. They can't last long
@memphismania323 жыл бұрын
@@xxdeedee why be rude to someone whos trying to be helpful?
@jeremyraeber42343 жыл бұрын
No they don't. Google sealed bearings and read. Call the manufacturers.
@misterspock35615 жыл бұрын
did it start when you were done?
@jeremyraeber42345 жыл бұрын
Ran in accordance with the manufacturers specifications.
@chefington02175 жыл бұрын
What size bearing are they do you have the number.
@jeremyraeber42345 жыл бұрын
42mm×15mm×13mm
@mab1230805 жыл бұрын
I like that background music.. who? Would this same concept apply to simpson surface cleaners?
@jeremyraeber42345 жыл бұрын
It will on the 20", but not on the 15" wand connect.
@mab1230805 жыл бұрын
Jeremy Raeber yeah I have the 20” similar to that except I can’t get the arms where the tips connect off the main shaft below where the bearings are. On yours it’s one long bar. On mine it’s two pieces. I can’t find a diagram anywhere. Do some have Allen keys or refers threading?
@chrischappell71175 жыл бұрын
Good video, that swivel looks like the same one on the GP Hammerhead, the BE, Whirl A Way and a couple others, in your opinion is it the same swivel? Thank you.
@jeremyraeber42345 жыл бұрын
I've finally was able to view the ones you mentioned in person and yes its swivel.
@jeremyraeber42345 жыл бұрын
Same swivel
@TheButtshd5 жыл бұрын
This was very helpful thank you
@jeremyraeber42345 жыл бұрын
You are welcome
@garysides41165 жыл бұрын
Are there any o-rings to replace? How does it seal water in? Do you have to take 4 cap screws and locknuts off? I am about to tear a 20" one apart.
@jeremyraeber42345 жыл бұрын
There are no o-rings. All the water goes threw the very center casting. The outer casting then clamps around it. Yes the cap screws and lock-nuts had to come off on this model. The failure in the design comes from not having sealed bearings, and not having the ability to grease the bearings. I hope that this helps you in your repair. Keep on fixin.
@gabrieladjei5174 Жыл бұрын
No my friend. There’s O ring to replace inside the house and a small one at the very bottom of the housing.
@RoadKen536 жыл бұрын
It's a T-27 torx bit. And your music really sucks.......
@pianomanw6 жыл бұрын
Very helpful. Thanks
@jeremyraeber42343 жыл бұрын
Thank you
@ldjames0016 жыл бұрын
Thanks for taking the time to do this video. I've paid others to do this. Now I can do it myself. Audio is fine. Your effort is appreciated.
@jeremyraeber42346 жыл бұрын
Larry James thank you for that. I work for a huge hardware store chain who loves orange. I'm the lead repair technician. We charge almost $75 for a carb cleaning. I had a really hard time trying to justify that much money for a repair anyone can do, and can be done in under 20 minutes.
@buckmaster55525 жыл бұрын
you've got to be kidding. Does this guy even speak english
@gilv96076 жыл бұрын
Excelente!
@calebcreech55626 жыл бұрын
What is the part number? Link?
@anselb20007 жыл бұрын
An otherwise good video is destroyed by all the camera/tripod noise! Might as well turn the audio off.
@jax00476 жыл бұрын
You can turn the volume off on your computer.
@joshboyfuture96986 жыл бұрын
I don't think he was shooting for a quality video as much as just trying to convey information to people free of charge. I think you did a fine job personally
@salpellegrini40475 жыл бұрын
Would have liked to hear him talk but it still showed showed enough to understand
@jeremyraeber42343 жыл бұрын
People who post these comments are just dumb trolls who aren't smart enough to make video content on KZfaq.
@darnellperez15037 жыл бұрын
Music sucks
@anthonye0846 жыл бұрын
Darnell Perez you suck
@cwallcw7 жыл бұрын
Great video, thanks! I appreciate that you added the comments.
@jeremyraeber42343 жыл бұрын
Thank you
@Matches8607 жыл бұрын
Thanks for taking time to do the video. I have the same mower which seems to have a carb problem so I'm keeping your vid handy as I operate.