Surface Cleaner bearing replacement

Рет қаралды 18,149

7 жыл бұрын

This is a Mi-T-M surface cleaner used with a 3500 psi pressure washer or bigger. You can't get the bearings from Mi-T-M, you can only purchase the whole housing that has the 2 bearings already installed which is around $125.00. I got the bearing from Bearings Plus for about $17.00 plus shipping which came out to around $25.00. The bearing is 42mmX15mmX13mm.

Пікірлер: 40

@theantisimp8258 3 жыл бұрын

Fucking A+ bro I have a edou 20inch, this just made me me confident af, love it, KZfaq is the dad I never had

@jeremyraeber4234 3 жыл бұрын

Lmao

@ohiovalleysoftwashrestorat6760 2 ай бұрын

i have the edou 20 inch will these fit that size?

@aaronorluck7632 2 жыл бұрын

Great video. 6302 bearing. For mine, I used an S6302-2RS, stainless with two rubber seals. $6 each (2 required) on Amazon.

@cwallcw 7 жыл бұрын

Great video, thanks! I appreciate that you added the comments.

@jeremyraeber4234 3 жыл бұрын

Thank you

@TheButtshd 5 жыл бұрын

This was very helpful thank you

@jeremyraeber4234 5 жыл бұрын

You are welcome

@berniemac8413 Жыл бұрын

Great video! Where did you get those pliers from?

@jeremyraeber4234 Жыл бұрын

Home Depot believe it or not.

@gabrieladjei5174 Жыл бұрын

Upon pushing the bearings back into the housing, he should have never hammer it back in. You just end up scratching the inside. Just apply little grease inside the bearing housing and outside the bearings itself and it should slide in like butter. Also apply small grease between the first bearing and the second as you pushed them done on the piston if you like to call it piston. It will work flawlessly. Thank me later

@chrischappell7117 5 жыл бұрын

Good video, that swivel looks like the same one on the GP Hammerhead, the BE, Whirl A Way and a couple others, in your opinion is it the same swivel? Thank you.

@jeremyraeber4234 5 жыл бұрын

I've finally was able to view the ones you mentioned in person and yes its swivel.

@jeremyraeber4234 5 жыл бұрын

Same swivel

@garysides4116 5 жыл бұрын

Are there any o-rings to replace? How does it seal water in? Do you have to take 4 cap screws and locknuts off? I am about to tear a 20" one apart.

@jeremyraeber4234 5 жыл бұрын

There are no o-rings. All the water goes threw the very center casting. The outer casting then clamps around it. Yes the cap screws and lock-nuts had to come off on this model. The failure in the design comes from not having sealed bearings, and not having the ability to grease the bearings. I hope that this helps you in your repair. Keep on fixin.

@gabrieladjei5174 Жыл бұрын

No my friend. There’s O ring to replace inside the house and a small one at the very bottom of the housing.

@HouseWashingRick 4 жыл бұрын

Jeremy, the ring you pulled out at 2:10 do you know what size it is. I brought mine and no store around here in my area has one.

@jeremyraeber4234 4 жыл бұрын

I don't. Try going to Fastenal they have every size.

@HouseWashingRick 4 жыл бұрын

@@jeremyraeber4234 ty bud

@mab123080 5 жыл бұрын

I like that background music.. who? Would this same concept apply to simpson surface cleaners?

@jeremyraeber4234 5 жыл бұрын

It will on the 20", but not on the 15" wand connect.

@mab123080 5 жыл бұрын

Jeremy Raeber yeah I have the 20” similar to that except I can’t get the arms where the tips connect off the main shaft below where the bearings are. On yours it’s one long bar. On mine it’s two pieces. I can’t find a diagram anywhere. Do some have Allen keys or refers threading?

@HouseWashingRick 4 жыл бұрын

Is this a Mi T M surface cleaner?? My beavis locking up on me on a job right now and I don't know how to fix it

@jeremyraeber4234 4 жыл бұрын

Yes it is.

@jeffheidenreich6131 3 жыл бұрын

What is the bearing number?

@sandspritpark 3 жыл бұрын

Deep groove bearings?

@jeremyraeber4234 3 жыл бұрын

Just a sealed ball bearing bearing.

@victorjordan3876 Жыл бұрын

On my lanz surface cleaner the rotating rod falls out.oes the clip stop that

@memphismania32 3 жыл бұрын

thank you....did yours lose power when it went bad

@jeremyraeber4234 3 жыл бұрын

It did . Then it froze.

@fendertree6624 3 жыл бұрын

What size are those bearings

@jeremyraeber4234 3 жыл бұрын

42mmx15mmx13mm

@chefington0217 5 жыл бұрын

What size bearing are they do you have the number.

@jeremyraeber4234 5 жыл бұрын

42mm×15mm×13mm

@xxdeedee 5 жыл бұрын

U didn't Evan grease It u wrongun

@jeremyraeber4234 5 жыл бұрын

That's because you don't grease sealed bearings. That's why they are called sealed.

@xxdeedee 5 жыл бұрын

@@jeremyraeber4234 so they never get greased then. They can't last long

@memphismania32 3 жыл бұрын

@@xxdeedee why be rude to someone whos trying to be helpful?

@jeremyraeber4234 3 жыл бұрын

No they don't. Google sealed bearings and read. Call the manufacturers.