Hello Mister Kiwi Rider, I am curious about fuel capacity after lifting the gas tank, Increased or decreased ? FXBB has small gas tank, any changes could affect riding range.
@MisterKiwiRider23 сағат бұрын
@@silverrambo1508 I noticed around 10 to 20km range deficit with this set of risers
@silverrambo15083 сағат бұрын
@@MisterKiwiRider Thanks for reply. I'll think about this mod to my Street Bob.
@BSThaGawdzBrassnDruMSektion3 күн бұрын
Think my mirrors just aren't meant t I b flipped smh
@BSThaGawdzBrassnDruMSektion3 күн бұрын
I love the mirror flipped but couldn't find a good angle for the left mirror. Couldn't see shit smh
@christiandouglas77716 күн бұрын
What if you just kept that portion of the exhaust off? It’d just be much louder
@MisterKiwiRider6 күн бұрын
@@christiandouglas7771 possibly unbearably louder. It would likely have a higher pitched crack type noise
@YesSir347 күн бұрын
A hole saw drill bit does the job too.
@thepurplecat59759 күн бұрын
I found this video to find out how to remove the baffles. I ain't putting any quieter ones in lmfao why would I want a quiet bike never mind a quiet HARLEY???????????
@thakery572015 күн бұрын
Back in 1990 I had a Sporty and the way the baffles were in the sliencers was a joke - just a plug midway the length of it.... so I took the silencers off and put a broom handle in one end and banged it hard on the ground, the welded in bung just came out real easy. My current bikes (2006 Sporty and 2010 Dyna) had a similar thing but the Catalyst made that a bit of a problem so I bought an extended drill bit ( that's just a drill bit fitted with a shaft to extend it) of the right diameter off ebay and drilled the baffle plate out, stuck it in the other end to put a big hole though the catalitic converter thing and hey presto, pipes that breath and you can see through them ! They are less restrictive and still fairly quiet and best of all it's cheap - a Harley dealer in London showed me what to do.
@norcal871816 күн бұрын
Looks good bud 👍🏻 might have to get me a couple.
@enigmajester66616 күн бұрын
I love this helmet.
@perryedsell311918 күн бұрын
Hi, did you ever fit the forward controls? If so, how was the riding position with the combination of Hollywood bars and forward foot controls. I'm thinking of doing something similar.
@MisterKiwiRider18 күн бұрын
@@perryedsell3119 I did fit them, yes. I'm glad that I did the forward controls. It was an ok riding position but I eventually went to 14 inch apes which was a fantastic riding position with the forwards.
@fatsquirrel255420 күн бұрын
Pipes are in a stupid location can’t mount bags with that rear cylinder pipe that high. But how else is Harley going to sell aftermarket parts🙄
@DonutLord3222 күн бұрын
That is definitely on the bucket list. Im planning on going down in January 2025
@DonutLord3222 күн бұрын
I'm going down in January next year and looking forward to it. It's been a bucket list item since I started riding about 3 years ago
@exoprasta26 күн бұрын
What’s the part number?
@MisterKiwiRider26 күн бұрын
@@exoprasta check this comment section. I don't recall off hand but I have posted it on another comment 🤟
@dennishardy440228 күн бұрын
Love my hd batt tender . I no longer have a hd but the tender which can be changed from lead to agm to li ion batteries is great as I have all 3 on different bikes. Always attached to some batt and has not failed in almost 3 years.
@kingcrumpetАй бұрын
Thanks mate. Just what I was wondering from across the ditch
@shresthaNiyuktaАй бұрын
❤
@wyattwells5810Ай бұрын
Thank u man, I was contemplating between drilling the hole out or cutting the quick detach parts and I'm definitely gonna cut
@davidmurray9193Ай бұрын
Will this work still with EU Harley's, bought a 2022 street bob and it has four O2 sensors on the exhaust two front and two at the rear and in the same situation want short shots at some point (stage one) but money is very short right now
@MisterKiwiRiderАй бұрын
I wish I could help but I just don't really know sorry
@davidmurray9193Ай бұрын
@@MisterKiwiRider no worries I'm confused why Harley put the senors on UK models, they know were going to get shut of the OEM exhaust lol
@harriperkio5773Ай бұрын
Some years ago I made 'inside tube' 500mm long from SS net, with 3-4mm holes and wrapped with ceramic wool... The noice came down around+20-27db, depending on length of the tube.. I could not feel any difference on the power.. yet neighbors were extremely happy..
@sc66glide2 ай бұрын
Ok... Yes i know this post is 3 yrs old, but i just put 14's on my 2003 softail, and i love the flipped mirrors look, but all i can see is my armpits.😂 Any suggestions? I want to keep them flipped, but i also want to see behind me, lol TIA!
@MisterKiwiRider2 ай бұрын
Hahaha, I totally understand. I had to get the mirrors with the longer arms and angle the mirrors more vertically than horizontally to overcome the same problem
@michaelgilmore9772 ай бұрын
Is your bike fuel injected or carb? I have a efi fatboy but have heard conflicting info on doing this.
@MisterKiwiRider2 ай бұрын
Yes, fuel injected
@AllenWayne1852 ай бұрын
Couldn’t you just cut them on the bike?
@MisterKiwiRider2 ай бұрын
I personally wouldn't but hey, if you've got the skills and confidence, go for it 👍
@theodavies87542 ай бұрын
Super Q aren't good if you have cams with bigger than stock overlap. On decel reversion popping in the pipes spits back into the inlet/carb. Yes they leave low end torque but it's not good to lug at low revs. 500 miles in will be a lot louder under load. Getting them back out after the plastic has melted is a long job. There is no shortcut to digging the fiberglass out with a hooked wire. GLOVES..... Outside. Really, the glass fibre dust will make everything sparkly for weeks. Next time I would definitely take my advice.
@Deltax15192 ай бұрын
Does this fuck up your 2 year warranty with HD?
@MisterKiwiRider2 ай бұрын
Only if I was trying to claim on the pipes themselves
@dennishardy44022 ай бұрын
If you dont have fishing line weed eater nylon works good too.
@BarbaritoAdolfo7773 ай бұрын
horrible sound
@imwhiteFTW693 ай бұрын
Do you need a tuner when removing baffles or since it’s before the o2 sensors I’ll be fine without a tuner? I’m assuming with a full exhaust obviously need a tuner. But what about this
@MisterKiwiRider3 ай бұрын
I didn't find that I needed a retune. There wasn't any noticeable change in performance
@jaccar32113 ай бұрын
Totally agree had some straight throughs on a sportsters and couldnt take the racket on a long ride, so returned it to standard, stopped all the poping as well.
@andrewkitchenuk3 ай бұрын
That air cleaner design is ridiculous, 100% style over function. First job is to replace it with the HD Ventilator flat cleaner.
@TheGorefeast6663 ай бұрын
Showing some love from The Native Nations Brotherhood we support the cause
@mikegrowgreens91253 ай бұрын
apparently you HAVE TO
@geralddreher91063 ай бұрын
I really thought about putting apes on my Lowrider ST but opted for risers instead. Seeing yours makes me wish I'd gone ahead with the apes.
@Zliminator77453 ай бұрын
I have a Bagger, impressed by the performance of the FXDR, I do think the air cleaner,exhaust and turn signals are butt ass ugly though...I had a Kawi ZL1000 before I bought my FLHTI, only good part of the Kawi was it was fast as hell....I love my bagger, it could use a little more balls though...lol!
@h.d.mech.mortenson20984 ай бұрын
Great job. I have the same bike and my old bike was also a Street Bob lol. I hated its stock exhaust as well. It’s silly that we have to spend more money to get a better sound especially after breaking the bank buying new bikes. You can also wrap the fibreglass mat with Saran Wrap as that’s what my mini grenade baffles had on them.
@brandmotivo4 ай бұрын
great video.... really helped me out do mine. thanks
@garydalton15424 ай бұрын
Eh just don't have that classic twin cam sound
@gerardwhitehouse-tedd65894 ай бұрын
Hi, can you tell me how many hours it took total to complete the bar change ? Chur
@MisterKiwiRider4 ай бұрын
About 4 hours 🤟
@anthonylingard72484 ай бұрын
love the look and the sound of the short shots but i find myself always worrying that my boot is going to melt on the pipe why they made them drop behind the the foot peg and not in front got me baffled
@dennisharrison47444 ай бұрын
I think taking it out putting it up in my house is better last longer I can get 4 or 5 years out one but leave it in the garage on a battery tender it won't last 1 season that's a AGM battery
@baylystruck66435 ай бұрын
This is what my concern was, and I’m considering the low profile oval air cleaner to swap. I’m having my forward controls put on this week
@acim22285 ай бұрын
but doesn't going to a 2 in 1 pipe kill the warranty
@MisterKiwiRider5 ай бұрын
Mods here in NZ don't automatically kill the warranty. Depends on what the warranty claim is and what caused it
@acim22285 ай бұрын
total spaced sorry brah big island you right
@maakatipa46135 ай бұрын
Hey Mate, gidday from a fellow Kiwi living in up state NY. Yeah just got me an intruder 800 for next to nothing, but it has short side cuts with no baffles, so it's pretty efing loud. Still have some ceramic baffle material from when I did up a vintage 1979 Honda Cm400 2 into 1. Was just checking out what other brands guys are using when your vid popped up ! Enjoy life there in God's own , cos I tell you what mate, it's phuking crazy here in the states.
@JSMotorbiking-mo8tb5 ай бұрын
Great jOB! My last two Bikes, I have not installed and aftermarket exhaust i have done exactly what you did. On my 2023 Indian Sport Chief is modified into shortys, is only loud on cold start then the sound changes after reaches normal temperature , i aslo inserted The GP baffle to help with some back pressure.
@irf8885 ай бұрын
Hi. Excellent video thanks. I've not seen the inside of the stock baffle so not sure if this is feasible, wondering if you think I can use a very long drill bit and drill through the baffle to get a straight through hole? Regards.
@MisterKiwiRider5 ай бұрын
Yes, you absolutely can 🤟
@Sandman04115 ай бұрын
I onced got pulled over by a cop in a bike, instead of giving me a ticket he wanted to race 😅
@MisterKiwiRider5 ай бұрын
😆👌 Nice!
@davedunkelberger70505 ай бұрын
You can use a dremell tool and just grind the weld off the baffle and pull it out
@filoIII5 ай бұрын
Take a dremel to those curb feelers.
@michaelneumann93266 ай бұрын
Hey Guy … where i can get such a bag for the handle bar ?? Greetings from germany
@MisterKiwiRider6 ай бұрын
Hello, that bag is a Harley-Davidson brand tool bag. You can get them from your H-D dealer 🤟
@infini19706 ай бұрын
Good to know this can be done. Out here I will risk loosing warranty and honestly I think the V&H mini Grenades will be worth the price. Just got the bike and don't wanna cut up anything.