Probably better off just getting the p1s? Has anyone experience
@Craftknights3D5 күн бұрын
The p1s wasn't out when I made the video. I recommend getting the upgrade kit or straight out buying the p1s
@PixelForgeLab5 күн бұрын
@@Craftknights3D Really ? you think is not worth it doing the Vision Enclosure ?
@Craftknights3D5 күн бұрын
Depends. The Vision enclosure ist cheaper and works Just fine. The p1s upgrade ist higher quality but also more expensive.
@PixelForgeLab5 күн бұрын
@@Craftknights3D that's ok then, as long as it works the same and it's cheapr ;) thank you
@samh-smith29314 күн бұрын
@@Craftknights3D Macht sinn! Danke 🙏
@theo300010 күн бұрын
Elegoo PLA+ works for me. Zero problems, great prints, inexpensive. A winner.
@diy_wizard15 күн бұрын
Danke, genau den spühspachtel habe ich auch und bin gerade dabei ihn zu benutzen ^^
@tobyk_804518 күн бұрын
Just use car wax
@chilloutsweet260119 күн бұрын
Does this work for PLA
@Craftknights3D18 күн бұрын
Acetone does not work on PLA. You can use spray filler and sand the model to remove layer lines.
@TheSimonarneАй бұрын
I wanna see foccacia cooked in a 3d printer that would be fun
@gw1814Ай бұрын
Asking the real questions here! :D
@michaelstraughn3465Ай бұрын
So you need a laser cutter, 3d printer, 3d resin printer, to upgrade your P1P?
@Craftknights3DАй бұрын
There are kits that you can buy and you can always outsource the laser cutting.
@hcpitcherАй бұрын
When steak. LOL
@CatBennyАй бұрын
You have just earned youself a new Subscriber... :) ... with an Mk4, some eggs, rice and a high electricity bill :D Worth it! (und Backpapier ;)
@kaizadkotwal12Ай бұрын
when is the baking vid coming out
@Craftknights3DАй бұрын
Soon!
@AndrasBuzas1908Ай бұрын
Baking in an enclosed printer 🤢
@yesyesno4521Ай бұрын
missed opportunity of 3d printing a fork
@Craftknights3DАй бұрын
Damn, you are right there!
@williamhai3717Ай бұрын
Fantastic video.
@davetjock1814Ай бұрын
I think you took the lay in layer lines a little too literally!! 😀🐣
@GordonFeeshmanАй бұрын
I love this video! Very funny and underrated! It was very interesting to see how the food was cooked, and whisking it with the nozzle was smart. I also found it very funny how you changed the site.
@Craftknights3DАй бұрын
Glad you liked it!
@YumiMattАй бұрын
I Agree, the quick code change in dev is so cool to make it look real. great vid. steak steak.
@lsg1EntertainmentАй бұрын
Can you paint after acetone smoothing?
@Craftknights3DАй бұрын
Sure. But you should apply a plastic primer before you paint it. If you don´t apply a primer then the paint will not adhere properly to the plastic.
@lsg1EntertainmentАй бұрын
@@Craftknights3D I see, that would also be a way to dull the shine.
@Craftknights3DАй бұрын
Exactly!
@Shojiki64Ай бұрын
The plastic bin is important. Do not use a bathtub
@Orbitechaerospace2 ай бұрын
here in Brazil the cheapest filament is around 18$ (the Elegoo),(obs: the creality one is 25$ +10$ of shiping)
@Andersenjonas2 ай бұрын
Where do i find that test print?
@justthat692 ай бұрын
Well, i have a lot of PP because i drank 2 gallons of water.
@dustinwhite52262 ай бұрын
Brand new out the box - both homing switches don’t work
@thePavuk2 ай бұрын
I expected that all wires will be white... for the sake of insanity
@reviewguyofficial3 ай бұрын
i bought a filament for like 7 dollars it was good I have some videos of the prints they are good a
@microcontrolledbot3 ай бұрын
Looks very cool
@pyroignis33054 ай бұрын
I just got elegoo pla+ having trouble with it warping and leaving thick springs hanging I'm areas
@theo300010 күн бұрын
215 is the sweet spot for me.
@jordanarellano80584 ай бұрын
What's stopping you from just using q dremel?
@1supertec4 ай бұрын
I use elegoo exclusively for PLA as its a great price and it prints really well also easy to get it off Amazon next day 👍
@SlowRkers4 ай бұрын
I've bought something similar, though from what mine showed we need to print it using ABS due to heat resistance properties. thus far using PLA is there any issues?
@mikegrant80314 ай бұрын
Shhh your gonna drive the price up
@xj770HUN5 ай бұрын
I would like to make a cosplay. But i fear some parts will scrape to each other, and at the "contact" paint will be removed. Any idea how to make more durable? More clear coats. Like matt varnish? Also do you have experience with spray putty? Will it scrape off easily? I need smooth surface. Thanks for any help!
@Craftknights3D5 ай бұрын
You can use spray putty to remove layer lines. You just need to prime it before painting and seal your paint job with a sealer. I recommend acrylic sealer (its available in matt and glossy). The primer and the sealer will keep the paint from scratching or peeling off but you will always have some wear in areas that rub against each other.
@xj770HUN5 ай бұрын
@@Craftknights3D Thanks! I was thinking about multiple layer of sealer coat is better for durability?
@TommyHoughton5 ай бұрын
Awesome video mate, love how it turned out! My workspace looks the exact same when I'm working on something haha. Cheers
@sarahmarieartstudio105 ай бұрын
This is so helpful
@peterpeter56665 ай бұрын
recently i tried different filament other then the bambu . I was suprised how well sunlu , giantarm, and polymaker pla print. I was especially impressed with the Giantarm silk pla . very shiny and smooth prints. I tried the blue gold and silver. The silver did not print as nice as the gold but very close
@tek90583 ай бұрын
i bet bambu IS sunlu filament. last time i ordered sunlu filament for 10€/1kg it was delivered in a bambu cardboard box. there are more reports just search for it.
@youtubehandlesuxАй бұрын
Bambu filaments are just repackaged sunlu.
@peterpeter5666Ай бұрын
@@youtubehandlesux can you prove this? cuz i suspect the same. i purchased a roll of orange sunlu for a project and it looked exactly like my bambu orange.
@aroncheek50925 ай бұрын
I'm still learning about slicers and have only just got my first printer, now I know my way around my printer and fixed a fault from factory I'm able print from start to finish now and I'm just about to get through my first reel of the anycubic standard pla , I have got through approx half a reel of the sunlu matte white pla and they both gave me good results. My printer is the anycubic Kobra 2 neo and apart from a tensioner nut that serves one of the guide wheels for z axis being put the wrong way around my Kobra is performing well, I'm impressed with it so far I was going to send it back until I diagnosed the fault
@RichM19675 ай бұрын
I bought Elegoo Rapid PLA for my Creality K1C -- It works better than the creality filament. Usually I don't need to gluestick, and the prints adhere nicely to the bed, and it pops off the bed with no residue. Residue should have been part of the test as cleanup is essential too.
@ainttakenanyshit5 ай бұрын
This "OK" review could have been GREAT, IF ONLY you used a honeycomb mat that would ACCURATELY show the good cutting performance of this unit. IF I were to take the time to review a laser unit, you can be damn certain that I would want to publish a video that I could be proud of and that would show the best results it was capable of... So there....
@Craftknights3D5 ай бұрын
I reviewed the laser as it would arrive at your door step. And it comes without a honeycomb plate.
@GaryMcKinnonUFO6 ай бұрын
Thanks for this, i'll try the acetone route since i have some. I've read many bad reviews about PVB filament so i'm not eager to try it.
@bobbygranito94756 ай бұрын
Very helpfull, thank you I am new at working with 3D printing so this was a big help.
@ruibernardo-hm4ou6 ай бұрын
Does the acetone method work with PLA?
@Craftknights3D6 ай бұрын
No.
@nebuchadnezzar476 ай бұрын
cool build but that print quality as absolute dogwater wtf... this thing prints worse than the cheapest ender 3 clone in existence
@johnwatrous30586 ай бұрын
How about sand blasting the PLA?
@Craftknights3D6 ай бұрын
If you have the means to do so. But you might loose some fine details.
@JamesRamsey-rg4ty6 ай бұрын
Where did you get that particular torture test piece from? I've seen variants, but not one with spikes.
@shaunimcgarva3296 ай бұрын
you can mix uv resin and baby powder too uncle jesse shows this and i do like it
@kylerathdesign6 ай бұрын
Is that filament tester available for download somewhere?
@maxbrinker93336 ай бұрын
Geeetech is really cheap stuff I don’t know how you managed to pay that much for it. It’s good for the price but it’s not great.
@chanakya_neeti_16 ай бұрын
What is this ABS, PLA, or PETG type of filament the fish one
@Craftknights3D6 ай бұрын
ABS
@bbrendon6 ай бұрын
so whats the tldr?
@krich1067 ай бұрын
I always assumed this was more due to the 3d printer and settings used. I don't own a 3d printer.
@Craftknights3D7 ай бұрын
You will always see some layer lines. Even in resin prints (barely visible).