I replaced my CV boot four months ago after watching your video, and travelled quite a distance since. Never done this before, and found it is easier than I imagined. Many thanks for the video help.
@albasoldier8 күн бұрын
So , you managed to do this under 30 minutes? Under 1 hour? Ive seen these parts from bosch for 45€? The fuck the garage charging me 400€ for?
@2LittleDickieBirds20 күн бұрын
Great, straightforward instructions that helped me replace mine. Thanks 👍🏻
@ding57923 күн бұрын
Thanks bro
@brendonrutherford511828 күн бұрын
Interesting video & a job well done considering all of the various appropriate tools were not utilised for home instructional purposes!! (fine) However & of some concern was the fact that "NO SAFETY GLASSES" were worn, "NO NOSE/MOUTH FILTER"was used against the "POISONOUS" dust that was floating around in the atmosphere when the drum was initially removed??? Also as a new bearing was being fitted there was no hand/finger protection (gloves) from possible dirt/dust contamination etc, etc.!! I'm currently learning this stuff at a training institution & with respect, if my tutor had of caught me implementing this level of wokmanship he would have booted my arse forthwith & given me low marks & rightfully so!! Sure these aspects I've pointed out (& with respect) may not be absolutely necessary but they duly display a good & totally professional level of competence!! Might not have been the way Grandad used to do it but in line with modern vehicle servicing methods & practices, they are without a doubt the right & proper way to do this type of work!! Safety is "PARAMOUNT" & it doesn't matter if it is in the home or the workshop as it makes no difference to any resulting accident!! As we all have to learn whatever please accept this critique with grace!!! As a side issue, we also put wheel bearings that are to be inserted into a vehicle & try & leave them overnight (or even a few hours) into a fridge/freezer to cool the bearings & therefore make their insertion so much easier!! (it surely works as the buggers simply fly in) 😀😁😋😛👌👌
@austinemuz8Ай бұрын
Thanks. This video was a great help
@papastashАй бұрын
Soooooperb
@CarSales-cv3spАй бұрын
Hi please help me with the colour of the wires on the first coil pack Can anyone help with the correct wiring colour for my ignition coil on a yaris 1kr engine I have three wires comes to the first ignition coil(Drivers side) The wires are (red) (white) and (black+white) Please give me the correct function of each wire I want to change the plug.
@seve1564Ай бұрын
I have called the dealership to change the distribution and they tell me that being such an old car (1999) they will surely have to order the spare parts from an external distributor to find them. I take them there so they can put original parts on me, not what they intend to do.
@TS-gg9dkАй бұрын
OK, but what about the adjustment at the rear disc brakes? That is what I need to sort out.
@mhorakli7918Ай бұрын
Very good video 👍🏻, does have a serial number to fit or just should be the same year model?
@tubetales17982 ай бұрын
Great vid, thanks mate... top man
@adamwalker73382 ай бұрын
Hanx!
@theirishceltireland2 ай бұрын
Thanks ❤
@jezmadden70022 ай бұрын
Worked great, cheers !
@Biometric_Excalibur2 ай бұрын
Gracias
@MrSnookerballs2 ай бұрын
to much copper grease used on pads and silicone grease should be used on the pins. glad you didn't do mine
@jackmaddesty2 ай бұрын
Thanks. Have to change all 20 studs on my car. Wish me luck😀 Great video so thank you👍
@gary88663 ай бұрын
You forgot to tell people you've got to press the brake pedal on that particular model or it won't go off
@mohitl16973 ай бұрын
Not correct way. Handbrake lever in drums will be seized. JLV recordings has a good video addressing this
@user-jg5tb8qj5f3 ай бұрын
I hv Peugeot 407 when I drive he show me control pression
@user-jg5tb8qj5f3 ай бұрын
Hi am tshegofatso Monnye
@robbo-_-693 ай бұрын
Absolute legend for this , i thought the nut was attached to the rod end haha 😂
@SoulFoodEqualsMusic3 ай бұрын
Just great all around
@elishalandry8534 ай бұрын
Anyone what size that belt is? 1445mm or 1475mm?
@dailydad63354 ай бұрын
Havr to replace my cv joint the threads on my one destroyed after i hammered it out of the hub.
@joolzhud4 ай бұрын
Brilliant
@DigiKiller4 ай бұрын
Gonna be doing this tomorrow on a 1.4 8v, should be the same yes?
@gjc90764 ай бұрын
Wrong wrong wrong, this just tightens the shoes and can cause drag and drum faliure!!! To do it properly, you need to adjust the via the drum. READ A MANUAL!!!
@richardtaggart92524 ай бұрын
How much copper grease dust collection
@gregzmanson4 ай бұрын
Thanks for sharing, there doesn’t appear to be enough wire to cut the harness..
@carltonbigdawg5 ай бұрын
thank you
@alansanczuk16305 ай бұрын
It’s a how not to do this Job.
@alansanczuk16305 ай бұрын
You didn’t change the rattle clips, or if leaving in at least clean them out. Or check and grease the guide pins and rubber shrouds
@chrisshave71295 ай бұрын
Great content thank you!
@user-dq2gm6rw6j5 ай бұрын
V
@Tinez875 ай бұрын
What's the best way to jack up the TT? There only appears to be cut outs on the sills for the scissor jack that comes in the boot! Thanks
@teemotomcat10175 ай бұрын
Very helpful! Thank you!
@crazygeorgelincoln5 ай бұрын
Thanks again !
@antonychiloane4965 ай бұрын
Bra help here mine does not have spark at all
@amerhodzic50855 ай бұрын
Hi...please how can I set to have time and date on my radio Display in my passat 6?
5 ай бұрын
How about the inner cv boot?
@felixwoukec39025 ай бұрын
Works fine👌 Thanks
@win-win776 ай бұрын
Thanks!
@greenball96 ай бұрын
Good video
@mikew3706 ай бұрын
Brilliant! The best tutorial ever.
@oakgreenben58887 ай бұрын
Legend
@kevinmaynord54167 ай бұрын
How do you take the headlight lens away from the housing
@user-sf7kl9uh7k7 ай бұрын
Don't geease the slide pins with copper, use silicone grease.