2 жыл бұрын
Пікірлер
@user-nt1xz6qn8x 2 күн бұрын
Excellent work, what kind of epoxy did you use, JB Weld? Can it be assembled without it? Why cut brushes in the lathe?
@francisalaeze6541 3 күн бұрын
Can it be fix
@paulocesardias847 3 күн бұрын
Qual a marca desse alicate
@youragronk6208 7 күн бұрын
Now to remove it?
@joshuacurry6073 8 күн бұрын
How do you install the spring that holds down the brushes?
@crnogor 9 күн бұрын
Majstore , postavi bi jedno retoričko pitanje . Ako bi se snažni anlaser 24 V preradio za konstantan rad - Alu rebrasto kučište , aksijalni provrti kroz njega za protok rashladne tekučine , ventilator za hlađenje . Pored toga ležajevi , pametna elektronska kontrola okretaja . Ako recimo on vuče pri pokretu motora 300 A staviti limit na 250 A pri max broju okretaja . zanima me , dali bi se brzo potršile četkice i eventualno kolektor ? Lijep pozdrav i sretan rad !
@hendyadheeva666 10 күн бұрын
iam the iron man
@josemolinadesales9936 10 күн бұрын
Hey my friend! What is the bearings model?
@pahadimamgain5397 15 күн бұрын
6.4 FS
@Iosif.dumitru01 16 күн бұрын
Hi, could the starter engine could be the cause for a slow starting 2.0 bkd engine?
@federicomahora2902 17 күн бұрын
Jedna ręką to sobie możesz zwalić konia
@Alexandre-iq8lp 17 күн бұрын
🇵🇹🇫🇷impec bon boulot 👍
@alihamdullah1296 18 күн бұрын
adamsın reis
@user-ih9ze8if5p 18 күн бұрын
👍👍👍
@pyme495 19 күн бұрын
You must be getting paid by the hour. I counted 12 squeezes of the crimper. And even then, it's not right. 😃
@magnum357225 26 күн бұрын
Svaka cast majstore, profi rad 💪🏻
@francescomosca6947 28 күн бұрын
Why change it? It seems it does not have clutch inside…how to diagnose a faulty one?
@Seboja 27 күн бұрын
In order to change the bearing, I have to remove the pulley :D
@francescomosca6947 27 күн бұрын
Thank you for the clearance, just asked becouse after changing poly v belt kit (belt and tensioner 20k km ago),my main tensioner start wobbling and my first tought was alternator pulley…so i checked and saw this one welded….first time for me …and i assume that if is welded and had no clutch inside,should be not this the problem. Thanks again for asnwer👍
@fernandoaceituno2022 Ай бұрын
Donde compraste el repuesto de puente de diodos
@x3r9g6 Ай бұрын
too many steps and isn't that a female connector, not a spade/fork
@mushahid_sheikh Ай бұрын
How much cost of this tester
@zhouzhou-sx5by Ай бұрын
You can try my machine ，crimping terminal
@Johnny99993 Ай бұрын
That is nou a spade connector. It is a female quick disconnect.
@jauniusnaujikas7504 Ай бұрын
Russian style Kak dlya selskoj nestnosti
@M_cfr Ай бұрын
Slm bu açıklayıcı bilgiler için teşekkür ederim Regülatör sağlamlık testi nasıl yapabiliriz
@M_cfr Ай бұрын
Yağı çözdüğünüz sıvıyı nerden bulabilirim teşekkürler
@SpikesMavic Ай бұрын
Excellent vid tanks you, but I wish you would use some dissposable gloves when working with all that crap on them !.
@KofaEdition-xd1yq Ай бұрын
Hargadenamu
@tobias8488 Ай бұрын
😂😂😂🤦♂️🤦♂️🤦♂️
@hbwproductions Ай бұрын
Is it ok if I put in an English comment here?
@OTZOLOTEPUNK 2 ай бұрын
Un mal crimpado al terminar la tarde.
@menthol-bonbon1726 2 ай бұрын
Where can I buy that type of pliers?
@genayacenko8180 2 ай бұрын
номера если можно плиз
@tomeks7775 2 ай бұрын
Which model of car has its types of ac compresor?
@Seboja 2 ай бұрын
VW Golf 4 1.9 TDi
@tomeks7775 2 ай бұрын
@@Seboja thanks
@trendafilgechev2219 2 ай бұрын
How many Watts is this soldering iron? 🤔
@user-in8hd2jc3k 2 ай бұрын
❤❤❤❤❤❤❤طريقة عملك تعجبني كثيرآ ❤❤❤❤يباركك الرب في عملك اريد أن أعرف عن نوعية سائل التنظيف هل هو السيترو مع تقديري وإحترامي لك
@alanstewart3425 2 ай бұрын
⭐ *PromoSM*
@xDarkmoonrising 2 ай бұрын
This is exactly what I needed thank you!
@ShakirAuto067 2 ай бұрын
Good working bro 😊
@DJV94022 2 ай бұрын
Postroch kaborch
@colinkohli3044 2 ай бұрын
nice clear video using only basic tools and a soldering iron......also teh detail on removing and replacing teh C ring on teh Bendix shaft was really cool....
@user-in8hd2jc3k 2 ай бұрын
❤❤❤❤❤❤أكثر من رائع
@marius4668 2 ай бұрын
Hello. Can you tell me please from what piece could be the sound like rubbing stones?
@Seboja 2 ай бұрын
May be 1: Bad bearings 2: The rotor will touch the stator
@marius4668 2 ай бұрын
If rotor is touching the stator could be seen from outside with engine on?
@Antsummerfield83 2 ай бұрын
Did this have a 10mm bolt inside not a torque? I have 2019 308 1.5 bluehdi and I have the tool socket for the spline but inside there is no t10 it’s a 10mm bolt. I can not find any tool to get his off as a 10mm socket will not fit through the spine socket I’m so confused as I’ve never seen a clutch pulley bolted on with a 10mm hex bolt
@khalidmehmood-544 2 ай бұрын
Good work
@fredsalter1915 3 ай бұрын
That DACTEM is gold!
@dadalifeview4327 3 ай бұрын
Thanks for this video. Good job👌
@ShakirAuto067 3 ай бұрын
Good work Sir 😊😊😊😊😊😊 support me 💯👍
@ramizyabac3256 3 ай бұрын
Güzel iş çıkardınız. Tebrik ederim. :)
@yash1152 3 ай бұрын
well, at least i got to know the proper name for this crimp. now i can hone my search.
@abhiatholi615 3 ай бұрын
Nice job