Thanks. I'm glad you found it helpful 🙂

Have you considered something like this? amzn.to/3W4rHLs

Thanks Guy 👍

Thanks for commenting, but by this stage, most/all of the grime that causes swirl marks should have been washed off. If you don't believe me, think about how a DA polisher works 🙂

Take the measurements using the setting you normally use. I'm not trying to recommend an optimum %PIR or foam thickness as these are subjective. The video shows how you can work out the %PIR for any setup.

Thanks for the great feedback. Enjoy your coffee 😃

Thanks Jacqui 🐈‍⬛

Thanks Alan. I'm glad you found the video useful 👍

Try using a penetrating spray e.g. WD40 between the (non)opening window and the frame. Spray it into the gap between them and leave for a few minutes before trying to push the window open. You might need to try this several times if it's been stuck for a long time. Good luck 🙂

That's great. Any fairly strong, thin object that fits into the gap will work 🙂

Thanks for the great feedback. There are a few other K4 videos on my channel which you might find helpful.

@@bigtedshome already watched and subscribed!! 😊

@@wondrousjaguar8907 Thanks 😊

Thanks for the great feedback 🙂

The detergent should be pulled up by the partial vacuum caused by the water flow through the nozzle. If the foam flows into the nozzle when it is upside down then this indicates that the nozzle is not blocked but you probably have an air leak. The first thing I would check is that the suction hose is attached securely to the nozzle and not damaged. Check also that the tank is screwed tightly onto the nozzle.

Good question. There's lots of conflicting advice if you google it. I prefer to use a window vac but if I was going to use a pressure washer on my windows, I would turn the pressure down and use a wide spray pattern. This explains what can happen if you get it wrong: Pressure Washing Windows? Bad Idea! www.windowworldofboston.com/pressure-washing-windows-bad-idea/

Looks good to me. Use the same setting as you used to take these measurements, then you will know that the 4% PIR is correct. If youbwant to lower the cost, you can always use a lower PIR if your car isn't too dirty.

I'm glad you found it useful 🙂

Thanks Kayleigh. I hope your Dad gets a beer or two for doing this 🙂

@@bigtedshome Absolutely! 🍺

Full details of the battery featured in this video are here: www.eurocarparts.com/p/lion-063-car-battery-3-year-guarantee-444770631

The one I installed came with a micro sd card

You're welcome 🙂

Thank you. I'm glad you found it helpful 🙂

It should be under warranty. It may be different in other countries, but in the UK, if you register it, the K4 now has a 5 year warranty

It's OK unless you can't get directly underneath the surface you want to clean.

Sounds like something different if nothing is working in the bottom oven. I would check if the two ovens have separate fuses first

@@bigtedshome remarkably I sorted it by setting the cooker's clock, the circuit had tripped, once the clock was set it worked as normal

@@ourtwotube Fantastic. Well done 👍

Enjoy your coffee 😁

Watching how easily you just pop yours in it’s making me think there’s something missing or just not right with the gun connection.

@@1791Tom You have to pull the black collar on the connector all the way up towards the gun before pushing the hose fitting in

@@bigtedshome I have measured the hose fitting and the insert inside the connecter and the hose measures at 9mm and the insert is 7mm. I think the gun must be for a different type of pressure washer.

@@1791Tom If that's the case, you should send it back. Amazon returns are very easy, I drop mine off at the local petrol station.

You need a connector like this on the end of your garden hose: amzn.to/4c440bD It then pushes onto the water inlet (towards the bottom LHS as you look at the yellow front of the K4). Hope this makes sense 🙂

Thanks Neil 👍

Nice one, I hope it works well for you. I would be tempted to run a hose down from the second floor though just to wind them up 😂

Thanks Karl. I'm glad you found it useful 🙂

I upgraded to the 10m braided rubber hose shown in this video: kzfaq.info/get/bejne/ldOAf9qTspPapoU.html It came from a company called direct hoses. There are direct links to the hose in the video description and in the comments.

That's not good. Did the repair shop say why they thought it was tripping the mains?

Thanks Dean 👍

Thank you 🙂

Thank you 🙂

Thanks Ben 👍

Thanks Deanne 👍

I've just used mine to trim the front hedge. Had it nearly 3 years now and have been very happy with it.

It's probably just water that's splashed over during the rinse cycle. It won't drain unless the water level gets higher than the max level marker. At this point, the Pythagorean syphon will start and empty the compartment.

Thanks Philip 🙂

Thanks Mandy. I'm glad you found the video helpful 🙂

I'm lending my K4 to a friend at the weekend, so I'll check this when I'm showing her how to use the machine.

@@bigtedshome thank you 🙏

@@Fraptor-co9bq I've just checked. The pressure reading on mine is also on medium when the patio cleaner is running

Thanks Mike 👍

Thanks Cliff 👍

Thank you 🙂