Great tools indeed, i use them daily and with coolant you can even bring up youre feeds slightly😊 With kind regards to my Ustad from belgium..👋
@CNCMACHINIST.2 жыл бұрын
Thanks a lot Cim Bom 🙂. We use air cooling because it increases the tool life a lot.
@weldmachine2 жыл бұрын
A Very Nice Machine to have in Any Shop. Definitely beats any Live Tool Lathe.
@seimela2 жыл бұрын
INCREASE YOUR LEADOUT FEED
@cassimvorajee28472 жыл бұрын
Assalamualaikum, brother Harun.
@m.i.b73133 жыл бұрын
Neden sıvı soğutma kullanmadınız
@SGIABC3 жыл бұрын
That's pretty amazing stuff. We have a tendancy in our shop to get most of the material removal accomplished before hardening to reduce machine time. But I could see in certain applications when precision is of upmost importance you would want to do it this way in one setup. That is if this material isnt already pre-hardened from the steel yard. :)
@legesupra42753 жыл бұрын
this is not a good demo for SECO tools you need to show off DEPTHS OF CUT and removal rate with carbide endmills!!!!!!!
@alessandrosantuari44343 жыл бұрын
Is a 62hrc material dude
@alessandrosantuari44343 жыл бұрын
Is fast believe me
@legesupra42753 жыл бұрын
@@alessandrosantuari4434 so basically hard milling:?
@ramazancolak31052 жыл бұрын
Do you not see the chips he is making.?
@legesupra42753 жыл бұрын
so slow
@HungNguyen-bd2ky3 жыл бұрын
62 HRC
@ramazancolak31052 жыл бұрын
He does not now the material...
@claudiugalea30383 жыл бұрын
What controller does the Machine has? It moves smooth on the 3 axis toolpath with the ball endmill🤟
Merhaba Ozan Bey. Iki CAM sisteminide kullandın ve kesinlikle EDGECAM tercih ederim. 18 senedir kullanıyorum ve birçok kişiye kısa sürede programı öğrenmelerini sağladım. Ara yüzü çok kolay ve sürekli yenilikler eklenen bir sistem. Bunun en büyük nedeni ise edgecami bünyesindeki bulunduran teknoloji devi HEXAGON. NXCAM büyük bir sistem ve alışması zor ve ağır. Seçenekleri çok fazla olunca kafa Karışıklığı yol açıyor. Ayrıca dynamic (edgecam da waveform olarak adlandırılıyor ) Milling/turning opsiyonu o kadar iyi değil . Bunu yaptığım testler sonucu Söyleyebiliyorum. Ama NXCAMIN en büyük avantajı ikisi bir arada cad/cam sistemi olması. Edgecam için İstanbul’da Metropolsoft Bilgi Teknolojileri Aziz beyi size tavsiye ederim
@Ozan_Gul4 жыл бұрын
@@CNCMACHINIST. ilginiz için teşekkür ederim hocam dediklerinize katılıyorum.
@christiannunez80314 жыл бұрын
What happen to 3:00? Why it stop feeding
@CNCMACHINIST.4 жыл бұрын
We have changed the feedrate
@dedinurhandoyo91714 жыл бұрын
Amazing..
@harezy4 жыл бұрын
12:12 tip went but they skipped that, lol. The flats at the end what a waste of time doing it like that 24:00 min mark. Are they manual chucks?? . What a lovely quite machine and shop tho
@yamakasi-d33024 жыл бұрын
Excuse me for this cnc machine name?
@CNCMACHINIST.4 жыл бұрын
YAMAKASI it is a DMG MORI DMC 1450V
@yamakasi-d33024 жыл бұрын
@@CNCMACHINIST. Thankyou verymuch
@legesupra42753 жыл бұрын
@@CNCMACHINIST. you need to be a little more aggressive with your machine, man
@keithhasafastcar4 жыл бұрын
Speeds and feeds?
@haotang22054 жыл бұрын
Why dry run ?
@Zukovec4 жыл бұрын
the fotage is speed up
@CNCMACHINIST.4 жыл бұрын
It is played in real time.
@jchelm19794 жыл бұрын
9:00 some very impressive plunge milling with a very long arbour on that tool. But completely unnecessary as it's a 5-axis machine. Simply index the machine and machine from the side using a shorter more rigid tool!
@CNCMACHINIST.4 жыл бұрын
Yes you are Right. But this part is for a open house meating to customers. What we want here was to show also our vibration damping holders in action. Not every body has 5-axis machine so this part was made for also for 3-axis machine owners. To make it short it is a Demo :)
@CNCMACHINIST.4 жыл бұрын
Machinist i Will use my long damping holder with finishing tool
@DiegoWorlitz4 жыл бұрын
Is it steel?
@CNCMACHINIST.4 жыл бұрын
Diego W. Yes it is
@pradeepm95354 жыл бұрын
Are they cutting with air ? Bcos they never used coolants
@back2mind4 жыл бұрын
high feed tools always run without coolant. the insert would break from thermal shock. air can be used to get rid of the chips but it doesn't really cool down the tool.
@jchelm19794 жыл бұрын
@@back2mind high feed tools do not always run without coolant. You can run high feed tools in aluminium and you would absolutely need coolant! Do not forget coolant does more than just cool, it serves 2 other very important jobs. It lubricates and it clears swarf from the cutting face. With the case of cutting steel, you do not need to lubricate the cut, the heat is removed with the chips and the air blast removes the chips that is why it is cut dry. Thermal shock absolutely plays a role with the use of coolant but it is only part of the answer in this case
@back2mind4 жыл бұрын
@@jchelm1979 trochoidal milling in aluminium with coolant is definitely new to me, the companies around here and most videos I've seen so far never use coolant with this kind of tools. might be possible that there are a few aluminium sorts that need coolant but in general they run without.
@jchelm19794 жыл бұрын
back2mind firstly video's generally run minimal coolant with aluminium for cinematic effect. Secondly trochoidal milling is not magic. Aluminium needs lubricating! It sticks to carbide like shit to a blanket! You're clearly not a skilled and experienced engineer!
@CNCMACHINIST.4 жыл бұрын
Yes we use Air for cooling
@Wmbhill4 жыл бұрын
This was a perfect machining video, very well done sir. Thank you for posting it.
@ecogames71654 жыл бұрын
29:30... Whats that? xD i like to moving moving xD
@steveprice7664 жыл бұрын
I'm not convinced about your machining strategy.
@allancnc4 жыл бұрын
I am sure Harun can make that piece much faster and better, this is just for showing at an open house at DMG i think, not sure. Its a big expensive workpiece, not cheap steel.
@dgin194 жыл бұрын
Коту когда делать нечего...
@jimsvideos72014 жыл бұрын
This seems like efficient paths, although the OD turning could use a little work to break up the long stringy chips. Also on the slotting op on the back side you could rotate the slot so it points down and so the chips fall out.
@staysheep8004 жыл бұрын
Your spindle sounds like an angry Hornets nest lol
@Muz9943 жыл бұрын
It's the sound of the air coming out of the air nozzles. The spindle on these machines (especially at low rpm) is pretty much dead silent.
@SuicideKang4 жыл бұрын
I tried reaching into my screen and and moving that air tip
@dopihead2 жыл бұрын
GET IT IN THE HOLE!! lol
@claudiugalea30384 жыл бұрын
what machine is this?
@khaihuynh85594 жыл бұрын
Perfect
@mustafademir72304 жыл бұрын
Vay be 3 eksen kullanıyorum efsane makineymis bu 👏👏👏
@jasperverbunt29515 жыл бұрын
Very nice job!
@draja76255 жыл бұрын
seco carbide endmill cutter part code number plz
@CNCMACHINIST.5 жыл бұрын
JS554100D3C.0Z4C-SIRA and part number 02810479
@JekaMandra5 жыл бұрын
on ali express those tools tungaloy named do it well too for low prices. 50Hrc? no problem for AH725.
@christophercolumbus8944 Жыл бұрын
lol aliexpreess
@CNCMACHINIST.5 жыл бұрын
Hi I used Cam software Edgecam . Cycle name is waveform and tools from Seco Tools 554L100
@ramvinayak51535 жыл бұрын
What is the cost of endmill
@danhnguyenvan36785 жыл бұрын
Can you tell me what sofware you program? from: VIETNAM Feelling sorry english can't be good
@danigroza25625 жыл бұрын
Hi my friend,one question,how is made the program for milling spiral outside to inside
@CNCMACHINIST.5 жыл бұрын
Hi Dani It is made by Cam system. Edge Cam Wavefrom
@christophercolumbus8944 Жыл бұрын
@@CNCMACHINIST. do you have instagram ?
@elWieslaw5 жыл бұрын
And how many pieces will work like this ?
@andy79905 жыл бұрын
i guess 1 :D
@CNCMACHINIST.5 жыл бұрын
When we drill a start hole in the center instead of i helix in the video, then we kan make 30-40 parts like this
@kabeladel45305 жыл бұрын
these new toolpaths are better than the old method
@vincomens5 жыл бұрын
Awesome part. Could be a little more aggressive with turning. Sandvik capto tooling would compliment this machine well.
@multiHappyHacker5 жыл бұрын
material?
@TabSeco-oh6rd6 жыл бұрын
DISCMiILLING VS HSS 加工比較動画
@meepk6336 жыл бұрын
Anyone know who this tool is made by? I couldn't tell.
@CNCMACHINIST.6 жыл бұрын
Hi Michael McDonald Do you mean the tool supplier or?
@meepk6336 жыл бұрын
I'm sorry. I was being sarcastic. The name of the tool maker was flashing on screen the whole time. Sometimes in multiple places. It was just a joke. My bad.
@Tsripper697 жыл бұрын
Thats not a DMC 1450....i think it´s a DMU75
@CNCMACHINIST.4 жыл бұрын
Correct :)
@christophercolumbus8944 Жыл бұрын
@@CNCMACHINIST. mono block or duo block ?
@CNCMACHINIST. Жыл бұрын
@@christophercolumbus8944 mono block
@ahmethalitmancar7 жыл бұрын
TÜRKİYE'den selamlar Ellerine Klavyene İşçiliğine sağlık Ustam.
@Nathan-mg7ho7 жыл бұрын
first 2 turning ops seemed to take forever
@hienaz7237 жыл бұрын
I'm kind surprise when you used shell mill to cut part in z axis direction . What kind of toolpath is that? What percent of step over ?
@rashesthippo7 жыл бұрын
Plunge milling
@CNCMACHINIST.7 жыл бұрын
Hien AZ Hi , it id plunge milling and my stepover is 10mm. Regards Harun
@thghy75167 жыл бұрын
very good......
@skumfuk-41807 жыл бұрын
This video is porn ;) I feel so excited when I see this video :D
@sleddarcheddar8 жыл бұрын
lolwtf...using a grooving tool to face at the beginning
@sleddarcheddar8 жыл бұрын
obviously I post in haste...now I see why, avoid tool change and move straight to next face grooving/turn op.
@Sketch19948 жыл бұрын
Also grooving tools are the most versatile tools having a great reach and a very thin stem...They just aren't that rigid. Edit: It's not even the same tool. The first one is a right hand face grooving tool with a curved support under the insert while the second is a straight round insert tool.
@fredrezfield16292 жыл бұрын
@@Sketch1994 it's called grooving tool for GROOVING