Or you can get the regular stack on gun cabinet. It doesn’t say ammo on it and you can stack it full of ammunition and it doesn’t advertise and it’s just as good.

Thanks for the video! I’ve had two of these Kayme covers now. Just wondering what you went with recently and if you’ve found a better one?

Can I use this product on ceramic coated cars

I thought this was a joke video 😆😂😂😂

I got here because I have a 302 HO that a previous owner put in my 1966 F-100 pickup. I thought a GT40 was an old Ford race car, one like at the Simeone Museum in Philadelphia. I'm 76 and forgot some of what I did to set the lifter preload in 2020 not long after I bought this truck. The specs for setting the preload to about 20 pound torque are confusing, different amount of turn from 1/4 to 1 full turn, but not consistent in opinion. After the heads were machined before I received the truck the stock pushrods were not long enough, so I had bought 6.300 and used different shims to set preload, from .020 to .040 inch shims. I want to do this again following firing order this time rather than other techniques. It is a little noisy since I changed oil recently.

Do you still have this car ?

Where did you get a 2 inch lift spindle? All I can find is a 3 inch lift spindle and it appears that when installed it raised the front too high such that the rear would be lower than the front.

What a moron. Buying a car that needs to keep topping off oil.

Great video

About to have this device

you save more cash upfront but you will actually pay more in the long run buying online. I have 5 year warranty and free replacement on new parts through the dealership.

I'm very surprised at your 70 MPG RPM number... I swapped axles in my 81 Capri when I put the T5 behind my 351w interceptor engine... at 70 mph I had 2000 rpm with 308 gears and factory size 16 inch wheels (GT wheels from a 92, my cousin's... lol) Is your car an automatic? Biggest problem I had, and how I ended up with my cousin's 16 inch wheels from his 92, were the brakes. the 11 inch front rotor and 9 inch drums were only good for about 70 mph once.. and that's 70 to 0 or 140 to 70... that car was incapable of 140 - 0 in one stop. My cousin put the SVO brakes on his, because after we put the Whipple on his, it would outrun the brakes every day of the week. Had the MAC shorty 351 conversion headers, off road H pipe and 2.5 dynomax mufflers with the polished stainless LX style tailpipes, sounded great!

Agree the getting the pinch bolt out and spreading is key! I’m on day 2 and getting it back on is a FN bastard

Not the same for Gen 5

I ordered one and I just got it and it looks thin and cheap, it doesn't look nothing like the one on amazon , it looks like it will rip at first wind.

dude exhaust is almost worthless until you yank those 4 cats out. runs better and sounds way better

Stock alternators are weak!

Will I need an alinement after I replace my oem one to lowering spendel

Wish my $130k sticker panamera had a back up cam. Like how tf did the original owner not spec a camera in on a high spec car

Hey Mike, I have a question, I have a 2010 panamera 4s, my oil temperature, and coolant temperature, have been rising, I'm trying to locate the oil temperature sensor, any advice?

The left over o rings are for the float valve , and the fuel inlet pulls out , the mid body has 4 tiny o rings.

So it was bought as a 7-8 year old car, with less than 20k miles? I think the costs are reasonable for a Porsche, however given the total miles i would hope not a lot has gone wrong. Great vid btw.

you can upgrade the air intake the throttle body the exhaust system and there are some good race chips

Hm

I found the "new" drain plug to have the same problem, almost wouldn't thread in properly, so I reused the old one.

Hm po

Do you still have this car? How about a six year update?

They all last 1 year.

I’ve owned a Macan for 6 years and outside of standard maintenance I’ve had one expense….a new battery. That’s it…runs like a champ.

when you ralied to say flowmaster , i unfollowed and deleted

Thank you for showing the brake in process people forget to mention it and it so important. Thank you for the tutorial im doing mine tomorrow.

Well at least the car cover took the UV rays instead of your paint!

Ive heard the convertibles really twist

Thanks for the instructional video Mike..my take down lever was worn also..Your video was short,to the point & helpful. Cheers.

use MAP Gas...

Holley efi system is a must too

Thank you 🙏 Worked flawlessly on mine and the idling has gotten so much better

Great work Mike!

Thank you for the information, do you know of a website that I can use for Japanese car parts?

That appeared to be a piece of hand rail for stairwell .

That’s what my uncle would call a roughin drop.

Thank you for sharing your experience. I want to buy one. My concern is the air suspension system. Other videos on that says its very expensive to fix when it breaks. How is your air suspension? Thanks again

That wouldn’t be the issue if it doesnt have a mass airflow sensor

Actually it's very cheap!

Rear tubular control arms are almost a must

I have code P055600 what this is??

I have questions my car is porsche panamera 2014 my hybrid system is not working sometimes I show engine check but sometimes work

I have a 2021 turbo S daily driver and i love it! I added exhaust intake and tune and she makes 900hp

All these need is CAI exhaust and a tune and its well into 8-900hp

My 2011 yz250f 4 stroke has fuel comming out of the overflow hose , it wont start, with new fuel , oil, and air filter,what do you think cause this to happen ??