I need help with a project. I need to convert a led with 4 wires to 3 wire connector. I got an electric scooter that had leds that had 3 wires. I want to install a led with controller but it has 4 wires.
@zeus73232 ай бұрын
This way worked so well but when I tried connecting the other LED onto the wires the light connected to the battery but it won’t light up the second LED strip I connected 😭
@poolsinfinite70552 ай бұрын
My Focus!
@ParkerHale063 ай бұрын
Thank's Wire Guy, very helpful
@WireGuyGlobal3 ай бұрын
Your Welcome Parker 🤙
@wamseekrishna3 ай бұрын
Thanks for the Video Sir
@WireGuyGlobal3 ай бұрын
Your welcome my friend :)
@robcruzh4 ай бұрын
Need to remove Center dash speaker first if equipped
@user-tp9ms1jf4p4 ай бұрын
Just a quick thing I've found... soldering from the inside out is easier than across. If you solder the inside wires first (red and green), then you won't have to crossover the other wires to solder the other two.
@sunseeker84574 ай бұрын
Personally I didn't watch this all the way. Interesting video. But the voice echo and background music together was off putting. You need a body mic.
@BigBodyPresence4 ай бұрын
Didn’t know you had to tin the wires first, thanks for the video!
@WireGuyGlobal3 ай бұрын
This makes it way easier for the wire to stick to the led
@Polarcaine5 ай бұрын
What can I do if my solder keeps undoing itself when I slightly bend it.
@ThreePhaseHigh5 ай бұрын
I can safely say your camera was out of focus
@user-fh7hn7pk7i5 ай бұрын
Thanks
@user-rj1qt3en7o6 ай бұрын
What a struggle! Thanks for the video👍
@OFCIFR7 ай бұрын
I did, but they ended up shortcuiting each other, I threw the strip in the trash and bought others to practice, my biggest issue being that I need to make a u turn
@PortalFPV9 ай бұрын
I tried this with 2 of the smaller pry tools with zero sucess. Bought a better set that had that larger tool. Still a PITA but eventually had they pull force needed to free up the dash. Just remember those are straight pins and out with all your might repeatedly
@grillmeisterflash9 ай бұрын
my solder wont stick to the led stripe what could it be?
@abdalqadr110 ай бұрын
❤❤❤❤
@ryanwormuth359610 ай бұрын
Anyone know what eeprom to remove to unlock it?
@RicardoMartinez-ne1re11 ай бұрын
Thanks helped a whole lot I appreciate people like you
@SkipRoGlo11 ай бұрын
What about the plastic coating over the copper connectors? Does the iron melt through it?
@Pablo4535 ай бұрын
It did on mine.
@sasquatch416011 ай бұрын
My touchscreen is not responding. Can u suggest any repair?
@onlymans165 Жыл бұрын
Does the dealer need to unlock the radio with a code??? Someone told me that
@galaxophone Жыл бұрын
After wasting about 20 pixels and 5 connectors, this is the video I needed ^.^ Thanks for making it! Will report back after I try this technique.
@theallinstalleresp9864 Жыл бұрын
Thanks for your removal!
@oxonomy2372 Жыл бұрын
How are these not shorting? It seems like you get the solder covering both the green and yellow pins at 5:03
@officialreniidon854 Жыл бұрын
Where is the rest
@justfor8550 Жыл бұрын
what temp thoooo
@NickzAndMikz Жыл бұрын
Hot
@ToastedBread_ Жыл бұрын
People recommend 325-350C
@retailpale Жыл бұрын
Yea but what about the power... that seems like it'd be the most important part
@egrstga255tga255 Жыл бұрын
Great video bro! Helped a lot!
@nmdesertrider Жыл бұрын
Kick ass video, straight to the effing point! 5FuckingStars!*****
@pierrehamelin5514 Жыл бұрын
I am really distracted by the poor camera focus
@Evermysticdesigns Жыл бұрын
what temperature on soldering tool ? it heats through the wire instantly , something i cant get :(
@bpatters69 Жыл бұрын
Thanks. Great video. To heat the heat sync is a butane torch too powerful?
@jk12428 Жыл бұрын
Good stuff Dude! Thanks🌟
@billjones7608 Жыл бұрын
what temp is your iron set at?
@CLAYTONCHAN1 Жыл бұрын
Thank you for sharing your ideas. Very helpful.
@paulmatakovich9096 Жыл бұрын
Do you know if you can swap the analog controls/knobs for the digital version
@PotatoDrummer208 Жыл бұрын
So what the hell do you do when the solder refuses to stick to the copper pads? Because I cannot get the solder to stick to the copper AT ALL
@WireGuyGlobal Жыл бұрын
Try a lower temperature. Start with 200c that usually fixes it
@jespero94 Жыл бұрын
What temperature do you use? I find it easier to tape the led strip to the table so it Will lie completely still and not move
@SGhiacy Жыл бұрын
Nice
@eldrugoalex Жыл бұрын
Would this give you access to the recirculation actuator? I would be better than remove the entire crash pad main assembly
@paintremedies4216 Жыл бұрын
Thank you so much
@mustaqahmed1863 Жыл бұрын
Nice. Meny thanks
@benreavely4891 Жыл бұрын
Exciting I think not. Exciting is something that happens when you skydive.
@brucemontgomery8136 Жыл бұрын
unable to find the products you used on ebay any help would be appreciated tytyty
@WinningTrades4U Жыл бұрын
That’s a terrible solder demo omg 😂 Delete this vid brah
@WireGuyGlobal Жыл бұрын
Thanks for watching Champ 😉
@djlykaen Жыл бұрын
Just did a few myself, quick tip to make sure nothings shorted out with a multimeter on continuity before putting on the heat shrink
@stubbydnutz Жыл бұрын
Will this work to submerge them in a pond?
@orhanozcelik3325 Жыл бұрын
Thank you dear friend
@hardcoregamerro81 Жыл бұрын
Thanks for the video. Had to put my cruise control back in.