Here in Texas, we had a bad winter storm in Feb 2021. Over 246 people perished, probably more than all of Canada in the same timeframe. I bought a Firman tri-fuel, luckily on sale at the local Costco. I run it for 30-45 minutes monthly/month and a half. My concern is the question of how clean is the electricity produced. Do I need to buy some kind of plug to clean the electricity? To plug into the house outlet feeding my computers, tvs, micro-wave. Would need 4 or 5 if they are sold. Can't find such a product on Amazon. Just don't know the product name, if it exists. Would appreciate greatly any info you may provide. Thanks. Also, looking to install a soft-start on my 3.5 ton AC. Afraid our electric grid is so-so and summers are as hot and could get deadly as winter cold.
@thomasbowman21325 күн бұрын
I got a 86 I've been fighting that c clip so bad I bent it up. Lol. Do you think it will be alright without it? I have the big retaining ring in just not c clip???
@BryanHansen4 күн бұрын
The large c clip or the little one on the end of the axle?
@thomasbowman21324 күн бұрын
@@BryanHansen the little one on end of axle, the big retaining clip I got in. The one I didn't get was the small c clip that goes on right before the locker cap?
@BryanHansen4 күн бұрын
@@thomasbowman2132 You are good. I don't have the little c clip on there. I had the same problem on one of my axles.
@thomasbowman21323 күн бұрын
@@BryanHansen thank you and appreciate the video.
@patricknguyen6326 күн бұрын
I thought triple A pumps are made by Comet, an Italian company
@Curnow-pz2xt9 күн бұрын
Thanks. I've been scrambling my brain trying to figure this out.
@765outdoors9 күн бұрын
I had the first gen kilo 1000(BDX), loved it. But it disappeared. Used the BDX software on my 17mach2 and it was dead nuts on at 200 yards and the bullet was tumbling. The new BDX versions are insane
@RetroYamaha9 күн бұрын
That battery charger is actually design to charge a motorcycle battery with 3amps that big battery you was charging looked massive shorly more amps
@BryanHansen9 күн бұрын
@@RetroYamaha two amp trickle charge is very common for large batteries
@idsullymichaels13 күн бұрын
great video - would love an update! And would like to see the natural gas set-up as that's my plan...
@BryanHansen12 күн бұрын
@@idsullymichaels I will get one put together. It is a really slick set up.
@HUMVEEDUDE23 күн бұрын
THIS GENERATOR WORKS LIKE A CHAMP! WORKHORSE, STARTED ON FIRST PULL, USED FOR 10 HOURS AND ONLY USED 1/2 TANK! .....HERE'S THE NEGATIVE ASPECT, VERY LOUD!!!! LOUD, OTHERWISE I RECOMMEND THIS 100% GREAT GENERATOR ♡ JUST LOUD!
@juliusiannellathecarfella5517Ай бұрын
Good video
@Doughboy-818-Ай бұрын
If I’m running it and using strictly extension cords do I connect the cord it comes with then connect my extension cords to that?
@BryanHansenАй бұрын
You can connect them however you want. Makes no real difference.
@melindakenagy3145Ай бұрын
Hey Bryan, thanks for this video!!! I picked up SAE 10w-30 Honda genuine oil from Home Depot will that work?
@BryanHansenАй бұрын
Yeah, that should work.
@mikem9953Ай бұрын
I always ‘slosh’ some fresh oil in the fill hole and let it drain just like you do. I’m glad I’m not the only one. lol. Also, I slide in a cow magnet into about a foot of fuel line for when I have to go ‘fishin for bolts’. Thanks for the video, as I’m trying to go through this destroyed, no brakes, entire wire harness cut up, no fuses, neglected, rigged up, clapped out, grease pit of a 300 now myself and make it decent for the new girlfriends Nephew. 😖. “Just get it to run if you can” No, I don’t work that way! lol.
@brandonpidalaАй бұрын
Colin Cowherd is that you?
@mitmiller8898Ай бұрын
Answered a lot of questions! Much better than the manual. Many thanks.
@NCboy4LifeАй бұрын
One bottle should be good to use for both front and rear differentials?
@BryanHansenАй бұрын
Yes
@michaelpatterson76802 ай бұрын
Great video, thanks!
@bksduskmirror12502 ай бұрын
Can you install thin on the peak? My chimney come out right on the peak and cant find a flashing that works
@BryanHansen2 ай бұрын
Definitely can
@frankv642 ай бұрын
I wouldn’t even bother with draining the filter. Just take the whole thing off like a canister filter. You’ll save 10 minutes and won’t have to worry about that hose dripping and making a mess
@ellap82312 ай бұрын
Still doesn’t work
@alanrodgers41562 ай бұрын
Thank you for sharing how you setup the generator. I followed step by step, on you went about it! Really appreciate it!
@casonolson82532 ай бұрын
I put that 2in riser on my 24 khaos and the throttle and brake cables have a lot of slack left over. The wires for the heated grips and reverse on the other hand are stretched pretty tight. I'm gonna have to do some digging and try to find a zip tie to cut
@BryanHansen2 ай бұрын
I did cut a zip tie in mine.
@josephcatano47052 ай бұрын
That tool not being too deep is nice, my 3d printer nozzle swaps could learn a thing or two. Especially when you consider we have to change those nozzles at or close to running temp for proper fit.
@bridgei_boi2 ай бұрын
What is that socket called with the 4 teeth that was used on the lock nut
@BryanHansen2 ай бұрын
Spindle nut socket amzn.to/457gpcj
@tommymcdonnelljr15822 ай бұрын
Thanks so much man I got the same problem with mine
@bigred24552 ай бұрын
Convinced me! I want one now.
@hasanmamedov50342 ай бұрын
Thank you
@stevecornelius5042 ай бұрын
Dropped mine just like you did. Very delicate. Great Video!
@jeremylowe23093 ай бұрын
Once again, I’ve seen this just as a propane and lpg gas line review. Great vid but try the gas option?
@BryanHansen3 ай бұрын
All three options work. I did not want to put gas in it because I want to use this as an emergency back up.
@CaptainThirdGen3 ай бұрын
thanks. Had the same issue with mine right now. This fixed it. Great video
@RanveerJayani3 ай бұрын
Thank you for a great video. All the steps are nicely, explained, and easy to understand. I have a question regarding installation of this pump when I already have a water softener. Water softener is installed at the point if entry to house (I have one hose which is before water softener to plant waters). Would it still be all right to install this pump on the water heater or I need to install check wall just after the soft water softener ?
@BryanHansen3 ай бұрын
Same installation. Right at the water heater.
@RanveerJayani3 ай бұрын
@@BryanHansen if I don’t have a check valve after water softener, won’t the back flow from the pump to water softener cause any problems (especially during regeneration of water softener)?
@BryanHansen3 ай бұрын
No. The check valve for the temp you install under the furthest sink (part of the kit). The circulation pressure is very very low and creates a loop at the tank NOT the entire house system. (The loop is just in the hot water line). I have a water softener And you’ll be fine.
@phuha43553 ай бұрын
Hi, the pump circulates through the crossover valve. What if for some reason, the crossover valve being blocked, will the system be over pressured? I don’t see anyone install a hammer arrestor or a relief valve. Thank you!
@BryanHansen3 ай бұрын
It’s very low pressure so no, it wouldn’t cause a problem
@gimmefuel72683 ай бұрын
Man THANK you so much for the video. And thank you for actually SHOWING the steps instead of just “glossing” over everything like most KZfaqrs do. 🤦♂️ Would you happen to have a video on “ removing” the spindle bearing & associated seals as well?? Thanks again 🙏🙏
@BryanHansen3 ай бұрын
Sorry, I don't have a video on it.
@gimmefuel72683 ай бұрын
@@BryanHansen did you also replace your axle seal, or was yours okay?
@BryanHansen3 ай бұрын
@@gimmefuel7268 mine was actually brand new. Full disclosure, I don’t know exactly why my axel sheared off the way that it did. My nephew had borrowed my mountain truck and I think turned the wheels too far and it caught the leaf spring and that’s why it snapped it off. It was a weird break. That axle still and spindle bearing was three months old.
@gimmefuel72683 ай бұрын
@@BryanHansen I was asking because I’m going to be replacing the u-joints on mine ,so figured I may as well replace the spindle bearing & outer axle seal while I was in there. I’ve already replaced my hubs & wheel bearings/ races previously.
@milfjey3 ай бұрын
hey man my oil dipstick is stuck inside how do i take it out
@BryanHansen3 ай бұрын
The plastic yellow or black one?
@milfjey3 ай бұрын
@@BryanHansen it’s a dewalt 4400 psi it’s grey no too long of a dipstick
@milfjey3 ай бұрын
@@BryanHansen broke off the oil cap and went inside i just don’t know what to do
@milfjey3 ай бұрын
@@BryanHansen you there?
@BryanHansen3 ай бұрын
@@milfjey I would probably look at an ez-out to get it out.
@mikegriswold67803 ай бұрын
Hoping this will work for me as well. Then just happened to noticed I know you. What a coincidence!
@BryanHansen3 ай бұрын
Ha! Small world, hope you're doing well Mike!
@mikegriswold67803 ай бұрын
I'm doing great Bryan. I hope all is well with you and can confirmed this worked for me too. My unit isn't even the same but operated similarly.
3 ай бұрын
Can you please clarify for me what oil you used. In the video you are using the bel ray 80w transmission oil. But the link you have in the description is for the bel ray 80w90 hypoid gear oil that is clearly labled hypoid (not transmission). Is there a difference in the two or is it just that they changed the bottle lable to say hypoid? Thanks for your info! The 80w transmission oil bottle says it's good for wet clutches. The hypoid 80w90 gear oil in your link says it's not recommended for wet clutches. Which one is the right one to use?
@BryanHansen3 ай бұрын
Definitely want the Hypoid. They changed the bottle.
3 ай бұрын
I understand that. But is the transmission 80w you used in the video actually hypoid or not? I bought the same bottle in your video a few months ago and just put it in my three fourtraxs yesterday. But realized the bottle didn't say hypoid on it so looked at your video again to make sure I got the right stuff. I did get the same stuff you are using. But if you look it up the 80w transmission oil says it is for wet clutches and the gear oil says it's not recommended for wet clutches. So, is the 80w transmission oil you used in the video hypoid oil or not? Do I need to change my fluid again with the bottle that is the 80w90 hypoid gear oil or is the 80w transmission oil like the bottle in your video OK?
@BryanHansen3 ай бұрын
The 80W or 80W-90 that I linked to (the one in the video and the one I mention) are BOTH hypoid
3 ай бұрын
Thank you for clarifying for me! I was bummed thinking I used the wrong one. @@BryanHansen
@texasproud56123 ай бұрын
My problem is what battery will fit in the spot beside the main battery, I bought a factory battery and it's to big.
@BryanHansen3 ай бұрын
I had the link in the description. This is the one that fits. amzn.to/3WgzgPE
@EasyAim13 ай бұрын
We use Haslet Roof Top platforms. A lot less cutting, it seals great, and actually looks good.
@sanpansam79773 ай бұрын
Excellent demonstration. Very helpful indeed.
@stevedolby78803 ай бұрын
What diff oil would i use for a 2002 honda trx450 also is the trx the foreman or do i have a trx frame and foreman plastics i just recently seen it says trx 450 on the frame
@BryanHansen3 ай бұрын
Either way, same oil. Make sure you can get the fill plug out first before taking the drain plug out. amzn.to/44eFNMx
@stevedolby78803 ай бұрын
Very good tip lol I remember striping the one on my big red thank you
@stevedolby78803 ай бұрын
Also would you know how much to put in. Not full tp the top right?
@BryanHansen3 ай бұрын
@@stevedolby7880 if it is like the 300 there is a "fill to port" on the front that was a 10 mm bolt and the rear was fill until it comes out the fill hole.
@stevedolby78803 ай бұрын
Okay thank you that helps alot. I am also doing the shift motor and shift angle sensor as my electric shift don't work I don't know were to start so gonna replace the shift angle sensor. If there's any info on that you can give that would be great. I'm not sure if I just unbolt and bolt back on or if there's things I need to worry about and adjust
@afishkind123 ай бұрын
Same here ... I was about to buy another one just now.
@gordonstockton68503 ай бұрын
Very helpful thank you..
@warwickcathro26504 ай бұрын
What do you do if the gap between the ridges is narrow enough so that the Dektite boot blocks the flow of rainwater to the gutter on a nearly flat roof?
@BryanHansen4 ай бұрын
Install it in a diamond configuration to help it not block the flow of water.
@smokey84004 ай бұрын
Nope CO carbon monoxide is slightly lighter than air and diffuses evenly throughout your garage
@mudmonsteroffroadfilms95084 ай бұрын
What year and model is your truck
@BryanHansen4 ай бұрын
85 k20
@jayyhq92894 ай бұрын
What 10 amp fuse is the one that will show blown ?? In the fuse box
@johndrewek32414 ай бұрын
You should’ve put it like a diamond shape the other the water don’t have a damn it goes around it
@BryanHansen4 ай бұрын
If you watch the video, I explain why I didn’t
@markbell75734 ай бұрын
awesome video, wish I had seen this before i took off the skid plate but at least I saw it in time to get the right oil, i was going to do what you said and stick some gear oil i had already. SUBSCRIBED!!
@markcooper854 ай бұрын
I just bought one for my work truck, we have gps’ trackers on trailer and truck so it’s been kinda draining my battery’s. I was wondering that once the correct settings are selected, will then default to them? Because I’ll be unplugging and plugging in the truck every night, I don’t want t to worry about making sure it’s set to correct settings. I want to come home, plug in truck and walk away, what’s your thoughts?
@BryanHansen4 ай бұрын
Personally, I’m your situation I’d install a Noco 5. amzn.to/3U5vdEj
@markcooper854 ай бұрын
@@BryanHansen I seen a video on them, looks like you just plug and go. Thanks for your input! I’m running dual battery’s, I was reading that I should connect one postive to one battery and the negative to the other battery?
@BryanHansen4 ай бұрын
@@markcooper85 I run a Noco 5 on my diesel on just one battery and it tops both off just fine. I don’t split the posts like you’re describing.
@mikekings5054 ай бұрын
did you check them all? You could have 2 bad ones?