Trung Tran

Пікірлер

@lamvlog951 11 күн бұрын

mong bạn rep cmt mình nhé , mình cảm ơn bạn

@lamvlog951 11 күн бұрын

Mình thử thay cell pin cùng kích cỡ bằng pin khác vào , mạch nó khóa pin lại luôn pin 8.4v đưa vào mạch ,điện áp ra chỉ có 0,8v , không biết có cách nào để bẻ khóa được không bạn , vì mình lỡ mua 2 cục pin lipo mới về thay thử , giờ bỏ thì uổng quá

@jatinkhirwal8363 4 ай бұрын

Best ❤

@user-mk2cz8zr7e Жыл бұрын

What have you wired into the C terminal?

@tuhin7ryt Жыл бұрын

Hello , I've canon battery . I want to use a powerbank output of 5v 2a and send it to a step up converter then make is 7.5v-8v . will it work ?

@TrungTran-uh8mn Жыл бұрын

i have use Step-up converter and when i take the photo seem like voltage drop and the camera stop working you might want to use Quickcharge 2.0 powerbank with Quickcharger trigger module and use 1 or 2 diode in series to have 8v at output for stability

@tuhin7ryt Жыл бұрын

@@TrungTran-uh8mn Thank you so much brother for your reply . I've tried with power bank and a boost module but it is nor worked . then i tried two lithium ion battery in series to give 8v still camera says that change the battery pack . Then i attached original lithium ion pack of battery it says 100% capacity and camera is running full ok . then i connect two lithium 18650 battery and connect them with original battery pack like one lithium and one original one side and other side one original and one lithium 18650 so when i connect it with the camera it says battery low . still i did not get it why its happeingn . hopefully this reply could help others . Thats why i am sharing my experience with LP-E10 battery . If you found any reason why its not working please share with me . and now i orderd new battery pack but still i am searching for solution . Thanks 💕💕

@TrungTran-uh8mn Жыл бұрын

can you send me some photo of PCB inside the battery if it's smart battery we need to do more step [email protected] facebook.com/leotranphotographer whatsapp: +84923071997

@tuhin7ryt Жыл бұрын

@@TrungTran-uh8mn I glued inside but i will send you picture for sure 💕💕

@giuliolabarbera6542 Жыл бұрын

hello, I need to do the same in a EN-EL7 , how i can do this? whitch component i need to replace whit wire?

@TrungTran-uh8mn Жыл бұрын

you can directly connect 8v to battery output terminal however to keep the PCB with output contact i must do that

@j03lPe Жыл бұрын

Hi. How you did it? Can you make a tutorial?

@josemiguelherrerapalacin2816 Жыл бұрын

Can the dummy battery send energy if I put it on a charger ??

@hardeepsingh-im5rg Жыл бұрын

Can u show clearly again we can't understand what u do plz

@ibrahimzayed7700 2 жыл бұрын

dummy batter when i buy one from amazon Is it safe for the camera? or not can u tell me plz

@1994guardian 2 жыл бұрын

congrats for you video my friend. i have tried your trick and it is working fine on 1080p but since i set the camera to record 4k it turns off when i hit the record button. Any idea. the input voltage is 8.1v.

@TrungTran-uh8mn 2 жыл бұрын

maybe it's voltage drop have you measure input voltage while recording

@dronowicz 2 жыл бұрын

Hi. I did as in your video, the battery started and shut down once. I think it's stuck, the camera can't see it at all. What should I do? Do you have a way? Thank you

@TrungTran-uh8mn 2 жыл бұрын

did you remove battery protection IC

@dronowicz 2 жыл бұрын

@@TrungTran-uh8mn I removed the IC and connected the pins as in the video. The solution to this problem: I connected a 2s lipo battery to the board and connected the camera to USB charging. After 24h, the camera started up. I now have a new problem, the camera without the lens works, but with the lens on it keeps restarting in a loop. Have you had such a problem?

@TrungTran-uh8mn 2 жыл бұрын

@@dronowicz have you try another battery never charging battery by usb after this mod because remove battery protection IC may cause over voltage charge

@seiichisatoshi9192 3 жыл бұрын

cảm ơn bạn !

@denciotv7213 3 жыл бұрын

can you show what the exactly do

@socstudio9639 3 жыл бұрын

mình cũng đang có 2 quả pin hỏng mà mạch của nó hơi khác của b. cũng nhìn thấy con ic đấy rồi :)) định mai làm thử xem sao :)) cơ mà mình nối thẳng vào 2 cực ra của mạch luôn đc ko hay qua mạch kia nó an toàn hơn ?? mình dùng pin f970 để làm nguồn :))