2012 jetta car won't move, is saying solenoid D and C what would those be?
@niktgorszykazdylepszy495117 күн бұрын
Thanks for helping! I recommend it for all!!!
@AraratGalumianАй бұрын
Производитель Мерседес не смог изготовить качественную деталь.а мы пользователи б.у машин мучается
@asteknikbeyintamiriАй бұрын
Hi firstly thanks for your sharing . i ordered sensor from china aliexpress and i replaced but it didnt failed .normally my fault was p173500 .after sensor replaced fault exchanged the p175e00 . Is this problem related sensor or adaptaion ? Can you help about it ? If it not problem for you can you share link you ordered the sensor thanks
@MuxtorXajiyevАй бұрын
Здравствуйте вы какому городе?
@craigminca7446Ай бұрын
Great job mate. These jobs are great money earners. Thanks
@VladimirSokhinАй бұрын
I see blue lines not violet. What about others pins on pcb? May be you have schematic diagram?
@orumslv2 ай бұрын
Passat 2018 tdi with dq381, sensors changed with SMP 132-532. Basic settings done one time after replacement. Problem is that car gets error P176f clutch 2 closes unintentionally when put in reverse or when you stop when driving. Any suggestions? Thnx
@obliv10us2 ай бұрын
BIG SOUNDTRACK YOU GET THE THUMBS UP JUST FOR THAT.
@ralgor1002 ай бұрын
Excellent I am computer engineer, and repair laptops to board level, people don't understand just have finnicky this is
@AldubaiMohammed2 ай бұрын
How can I obtain the tools used in the pickup process, such as connections and devices?
@efficy86152 ай бұрын
Hi, can I use different part number ecu with cloning on golf mk7? Or it have to be same?
@mechasoft2 ай бұрын
if you have hardware with ending F, you can use only F, if you have E you can use E L N P but you must pay attention with newer revision - can be different.
@marvinmphaphuli38642 ай бұрын
Hi what flux is that please. Does it work on aluminium contacts that have oxidation layer?
@mechasoft2 ай бұрын
here are normall cupper contacts. We use standard Flux such as NC599
@marvinmphaphuli38642 ай бұрын
What flux is that?...
@prathipkumaratputharajah78123 ай бұрын
I am not going to solder it my hands are shaking I am going to give it to young geeza
@andersonbradock32843 ай бұрын
Boa tarde,vc conserta modelo da Mercedes b 180 2009
@noddy80643 ай бұрын
I have a dq500 back from reconditing however, If i travel 11 km from cold and it goes into emergency mode p173600 .on 3 separate trips all plotted with texa one common pid is oil temp 58 to 64 degrees . they had me carry out relearn basic settings this made no difference . They were talking firmware may need to be checked it's up to date . I feel they need to get of the fence and have me take it out again so they can fix it right the second time and replace the sensor for gears 246R as i can only drive in 1357 when in limp mode and get out and push it if i need reverse (go VW) 130966 km
@cedricduchateau33073 ай бұрын
Combien demande tu pour réparer sa
@twfig13 ай бұрын
Can we contact you to send the unit to you for repair?
@claudiolopesdias94534 ай бұрын
ONDE POSSO COMPRAR ESSE EQUIPAMENTO
@ismail91604 ай бұрын
Thank you for the information ❤
@sampler_ek4 ай бұрын
Is it possible that this sensor causes the car to jerk in first gear? There are no error codes
@mechasoft4 ай бұрын
check pressure values without starting engine.
@sampler_ek4 ай бұрын
@@mechasoft i Think it was lower than 0
@mechasoft4 ай бұрын
@@sampler_ekhow many lover? 0.05 or 0.5?
@sampler_ek4 ай бұрын
@@mechasoft when engine was started it was -0,08 but when not, i dont remember. I’ll go to car mechanic tommorow and then i will se
@mechasoft4 ай бұрын
@@sampler_ekIf engine was started and gearbox were in N or P, then values looks ok (if on both clutches you have similar values).
@user-nt1nn9br4t4 ай бұрын
Мерседес дерьмо а не машина!
@andreichesalin39904 ай бұрын
Ничего не видно . Тема ремонта не раскрыта
@MyMathex4 ай бұрын
how do you remove the cover?
@andreichesalin39904 ай бұрын
У WV мастера краешек чёрного корпуса выламывают и тогда есть возможность поддеть и начать приподнимать крышку отклеивая герметик. Спирт и фен в помощь
@MyMathex4 ай бұрын
@@andreichesalin3990 thank you
@benjeminotchabadino34005 ай бұрын
👍
@guillermohcc5 ай бұрын
If I send my part, can you repair it? where they are located?
@mechasoft5 ай бұрын
If you are 'gearbox repair workshop' and you have equipment and knowledge (how to dismount and mount) then we can help you. We are located in Poland.
@guillermohcc4 ай бұрын
@@mechasoft I'm from Mexico. and I have a small workshop with the necessary equipment to disassemble and assemble the transmission. but repairing the controller unit is a problem here in my country. can you help me?
@mechasoft4 ай бұрын
Yes, please contact with us via email: [email protected] or via WhatsApp +48666377744. Rafal
@user-pw9er8xm1o5 ай бұрын
Добрый день ! Как можно с вами связаться. Шкода Кадиак 2017г 117000 пробег дизель. Также причина пропадают четные передачи и зх
@user-bi1wd6ig1z5 ай бұрын
Please, sir, if you can send us where we can buy this sensor, because it is available on Ali Express, but I am not reassured
@edwin801697795 ай бұрын
what I should to do if I get this error P175E00 after changing these sensors...
@mechasoft5 ай бұрын
Perform basic settings ;)
@sazimam5 ай бұрын
Would yo share a video of HOW TO open the cover, please ?
@mechasoft4 ай бұрын
pry off the lid or cut it ;)
@diagauto46896 ай бұрын
It doesn't work. After two or three months the same problem returns
@mechasoft6 ай бұрын
probable causes: Faulty, low-quality sensors. incorrect installation (overheating). undiagnosed primary defect of the gearbox (hydraulics), which leads to damage to the TCU’s sensors.
@HellaNooBs6 ай бұрын
Get the OEM sensors
@quadriabubakar70957 ай бұрын
Hello,i got these two codes after scanning, is the VGS faulty? 0766 An open circuit has occurred in the control loop for componentY3/9y4 (CVT) torque converter lockup clutch control solenoid valve 0776 An open circuit has occurred in the control loop for componentY3/9y2 (CVT) secondary control solenoid
@Daniel-qs8ec7 ай бұрын
great video, but is there a specific way of getting that goo off the PCB? i have a few broken wires on both sides and a broken cap.. its a pain in the ass to remove all the goo though.
@shimon24768 ай бұрын
What ks the price to repair one of rhe input speed sensor arms on the tcu?
@hunkenpunken8 ай бұрын
WHAT COMPANY in Europe has these refurbished to buy? We have a Mercedes B170 2009 that we have to fix this gearbox problem. Please give suggestions here. We are in Sweden but can import from any country.
@NicholasRiviera-Dr8 ай бұрын
Great video. What is the gel stuff called that covers the circuit board (under the cover) and how do you remove it?
@unaibilbao52228 ай бұрын
great video, thank you very much. Where can I find the presure sensors part numbers??? Or where can I buy them??? thank you
@sazimam5 ай бұрын
Search for SMP132 all sensors are the same. Cheaper ones lasts only 1000km , original ones are for rest of the life of VSG vehicle, means 100k km approximatelly - tested on several cars already. Original part number is not available since the VAG does not sell these pressure senders separately. Price of the whole mechatronic computer is as low as 10USD for the factory quantities so there is no reason to repair such mechas. Cheers
@as1fh8 ай бұрын
Hi, I bought a brand new mechatronic unit for my vehicle and have performed basic settings but sometimes the gears stop working and can see error codes P176B and P176C. Should I try basic settings again? There is also option for ‘Initialisation of clutch friction coefficient after mechantronic change’ but I’m not sure about that
@tordherflower9 ай бұрын
nice video,plz help me someone,i cant improve soldering tips to connect the wires......how to do...thanx
@abiodunadeyinka9 ай бұрын
What is the solution to a drive Authorisation fault 051300
@mechasoft4 ай бұрын
If not whole eeprom overwritten with 0xFF then possible solution is rebuild eeprom. If whole overwritten (all data lost) only new unit is solution.
@gaijins309 ай бұрын
Hey great video, from a mechanical point of view, what parts are required from a DQ250 to a DQ381 conversion apart from TCU, DSG box etc?
@qassimnooraldeen91179 ай бұрын
Good job 👏
@user-vv9du8zo9q9 ай бұрын
bonjour je souhaiterais acheter votre soft mais es que vous auriez une base de donné pour effectuer les réparation sur divers de calculateur?
@habibizhafranzhafran83439 ай бұрын
Apakah anda permah mendapatkan fault terperature sensor transmission
@habibizhafranzhafran834310 ай бұрын
If i do it ...what after treatment need instal sofware like that...or ready to used
@sazimam3 ай бұрын
Ready to go immediately
@xhaferkrasniqi905110 ай бұрын
hi thank you very much for the video, i have a question, when one of the sensors is damaged, is it neseseru to change both of them or only the one that is damaged? thanks
@sazimam3 ай бұрын
Only the damaged one
@habibizhafranzhafran834310 ай бұрын
Inside the box why very much fluid what thats normal... And after do this what you use glue for closed the box... What the box sterilized from fluid or no problem if fluid come in the box from indonesia
@habibizhafranzhafran834310 ай бұрын
What treatment for opening cover...very hard...
@phantom700X11 ай бұрын
If the unit doesn't have canbus communication . Wakeup error. Only 100mA on bench. Do you can repair it ?