Repair mechatronic VAG DQ500 Clutch Position sensor K1 and K2 10666 10668 P1735 P1736

Рет қаралды 62,249

Mechasoft

Жыл бұрын

Diagnosis and repair VAG TCU 0GC/0DE mounted in DQ380/DQ381/DQ500 gearboxes.
10666 10668 P1735 P1736
mechaprog.com

Пікірлер: 75

@craigminca7446 Ай бұрын

Great job mate. These jobs are great money earners. Thanks

@GigiBeleaDK Жыл бұрын

Well done ! :)

@LARSDIAGAUTO Жыл бұрын

Merci poto 👍🤝🙏💪🛠️❤️🌹🌷✌️😚

@as1fh 8 ай бұрын

Hi, I bought a brand new mechatronic unit for my vehicle and have performed basic settings but sometimes the gears stop working and can see error codes P176B and P176C. Should I try basic settings again? There is also option for ‘Initialisation of clutch friction coefficient after mechantronic change’ but I’m not sure about that

@qassimnooraldeen9117 9 ай бұрын

Good job 👏

@hugosolis9300 4 күн бұрын

2012 jetta car won't move, is saying solenoid D and C what would those be?

@AmyCMass Жыл бұрын

Amazing video, thank you. What's the usual operating temperature of the gearbox fluid, please? Mine is showing an average of 90c

@mechasoft 11 ай бұрын

Its ok

@shimon2476 8 ай бұрын

What ks the price to repair one of rhe input speed sensor arms on the tcu?

@xhaferkrasniqi9051 10 ай бұрын

hi thank you very much for the video, i have a question, when one of the sensors is damaged, is it neseseru to change both of them or only the one that is damaged? thanks

@sazimam 3 ай бұрын

Only the damaged one

@Harry-tw7gu Жыл бұрын

Hi, thank you very much for this helpful video! Is there anything you have to do after changing the sensor? Like an adaption or teach the TCU?

@mechasoft Жыл бұрын

Basic settings ;-)

@filipkollar1365 4 ай бұрын

What if basic settings are not possible to perform after the sensor change? Thank you@@mechasoft

@mechasoft 4 ай бұрын

@@filipkollar1365 Try several times up to success, try to erase all learned settings and try again. After every retry you must perform fully 'shutdown', so ignition full of, wait few seconds and start again.

@asteknikbeyintamiri Ай бұрын

Hi firstly thanks for your sharing . i ordered sensor from china aliexpress and i replaced but it didnt failed .normally my fault was p173500 .after sensor replaced fault exchanged the p175e00 . Is this problem related sensor or adaptaion ? Can you help about it ? If it not problem for you can you share link you ordered the sensor thanks

@user-pw9er8xm1o 5 ай бұрын

Добрый день ! Как можно с вами связаться. Шкода Кадиак 2017г 117000 пробег дизель. Также причина пропадают четные передачи и зх

@sanderhawkins533 Жыл бұрын

Hi, thank you for the video. What would be the symtoms of the pressure sensor not working. Would the tcu shift poorly ? My rs3 gears 1,3,5,7 all seem to have issues.

@mechasoft Жыл бұрын

Possible but best way to check that is make full diagnostics.

@sanderhawkins533 Жыл бұрын

@@mechasoft 👍 Thank you!

@abachannel903 Жыл бұрын

Good work, what type of solding wire you are using in order to resist to the engine high temperature?? Thanks

@mechasoft Жыл бұрын

Temperatures higher than 120-130 degrees in gearbox destroy everything other... so in this case, your wires are not important.

@noddy8064 3 ай бұрын

I have a dq500 back from reconditing however, If i travel 11 km from cold and it goes into emergency mode p173600 .on 3 separate trips all plotted with texa one common pid is oil temp 58 to 64 degrees . they had me carry out relearn basic settings this made no difference . They were talking firmware may need to be checked it's up to date . I feel they need to get of the fence and have me take it out again so they can fix it right the second time and replace the sensor for gears 246R as i can only drive in 1357 when in limp mode and get out and push it if i need reverse (go VW) 130966 km

@triplemarrano Жыл бұрын

What kind of soldier do you use? An special one?

@mechasoft Жыл бұрын

Standard tin

@user-bi1wd6ig1z 5 ай бұрын

Please, sir, if you can send us where we can buy this sensor, because it is available on Ali Express, but I am not reassured

@unaibilbao5222 8 ай бұрын

great video, thank you very much. Where can I find the presure sensors part numbers??? Or where can I buy them??? thank you

@sazimam 5 ай бұрын

Search for SMP132 all sensors are the same. Cheaper ones lasts only 1000km , original ones are for rest of the life of VSG vehicle, means 100k km approximatelly - tested on several cars already. Original part number is not available since the VAG does not sell these pressure senders separately. Price of the whole mechatronic computer is as low as 10USD for the factory quantities so there is no reason to repair such mechas. Cheers

@lorisbello6352 Жыл бұрын

Bonjour le capteur K1 correspond au vitesse R-2-4-6 ou c’est le K2 ?

@MaLaiMo312 Жыл бұрын

Bonjour le capteur K1 correspond à la vitesse 1-3-5-7, K2 correspond à R-2-4-6, je suis Taïwanais !

@anouaryazid3310 Жыл бұрын

Thanks for this helpfull video, i tried to replace K1 taken from damaged TCU, but same problem, P173500, problem can provide from another thing ? or just the sensor K1 ? thanks

@mechasoft Жыл бұрын

Perform „basic settings”

@GarageNation353 Жыл бұрын

Hi. I wonder can you help. I've recently carried same repair. I now have both values the same with no pressure. When I select the gear in the car the pressure rises to 1.8bar, fault code p175e is logged for clutch unintended closing and a gearbox warning comes up. Clutch K1 pressure drops to 0. Thanks

@mechasoft 11 ай бұрын

Perform basic settings

@carloscanalesoffen 8 ай бұрын

Hi, I have the same problem you describe (fault code p175e after changing pressure sensor and working ok for 2 weeks), did you manage to solve it with @mechasoft answer of performing basic settings or another alternative?

@GarageNation353 8 ай бұрын

@@carloscanalesoffen If it was working ok and now it's not. Recheck pressure values in case your solder has broken

@boots-dx7tn 8 ай бұрын

Hello I have replaced both pressure sensors and now they stay close to 0 bar and now error code P175D and P176E. Which software/procedure should I use to reset DQ500 at factory setting please ? The VCDS basic settings of transmission dont solve it. Thanks.

@GarageNation353 8 ай бұрын

@@boots-dx7tn When you select gears does the pressure rise to 2.6bar and the goto back to 0 and bring up your pncodes?

@marvinmphaphuli3864 2 ай бұрын

Hi what flux is that please. Does it work on aluminium contacts that have oxidation layer?

@mechasoft 2 ай бұрын

here are normall cupper contacts. We use standard Flux such as NC599

@edwin80169779 5 ай бұрын

what I should to do if I get this error P175E00 after changing these sensors...

@mechasoft 5 ай бұрын

Perform basic settings ;)

@orumslv Ай бұрын

Passat 2018 tdi with dq381, sensors changed with SMP 132-532. Basic settings done one time after replacement. Problem is that car gets error P176f clutch 2 closes unintentionally when put in reverse or when you stop when driving. Any suggestions? Thnx

@ananstar-tx2gk Жыл бұрын

Hi ,what name gauge pressure?

@mechasoft Жыл бұрын

It is gauge included in typical hand pressure / vacuum pump. Nothing especially accuracy.

@AnNuurBudiUtama Жыл бұрын

what is the name of that sensor? i want buy on ali

@mechasoft Жыл бұрын

Pressure sensors for DQ380/DQ381/DQ500 0GC,0DE

@kavamahangaalainfranck1258 Жыл бұрын

Possible to get thos esensors

@mechasoft Жыл бұрын

Yes "my friends" sell them. Look on popular markets such as ali... If you need original you must look for mechanically damaged TCU's.

@bogdanionescu1050 Жыл бұрын

@@mechasoft name a friend who sell it

@sampler_ek 4 ай бұрын

Is it possible that this sensor causes the car to jerk in first gear? There are no error codes

@mechasoft 4 ай бұрын

check pressure values without starting engine.

@sampler_ek 4 ай бұрын

@@mechasoft i Think it was lower than 0

@mechasoft 4 ай бұрын

@@sampler_ekhow many lover? 0.05 or 0.5?

@sampler_ek 4 ай бұрын

@@mechasoft when engine was started it was -0,08 but when not, i dont remember. I’ll go to car mechanic tommorow and then i will se

@mechasoft 4 ай бұрын

@@sampler_ekIf engine was started and gearbox were in N or P, then values looks ok (if on both clutches you have similar values).

@user-yw8dj8kp2p Жыл бұрын

hello bro can you tell me referance senor ? i have this error P173600

@mechasoft Жыл бұрын

Check pressures and everything will be clear ;-)

@reparatiifrigiderebucuresti Жыл бұрын

I changed the sensor, and is not function. The pressure is 0, and the gearbox enter in error immediatly.

@mechasoft Жыл бұрын

Maybe new sensor is faulty or you have weak joints.

@reparatiifrigiderebucuresti Жыл бұрын

@@mechasoft , new error is P175E00

@reparatiifrigiderebucuresti Жыл бұрын

Thank you very much for this video. Problem was resolved, whith your help,. The gearbox was reset at factory setting and adapting and now is ok.

@boots-dx7tn 8 ай бұрын

Hi, I'am exactly in the same case: both new pressure sensors stay close to 0 bar. Which software/procedure did you use to reset DQ500 at factory setting please ?

@alexandrsmirnov4551 4 ай бұрын

Same story here. I changed K1 and transmission immediately enters fault mode not allowing to run basic setting "dure to safety". Pressure readings are zero. How to factory reset it?

@diagauto4689 6 ай бұрын

It doesn't work. After two or three months the same problem returns

@mechasoft 6 ай бұрын

probable causes: Faulty, low-quality sensors. incorrect installation (overheating). undiagnosed primary defect of the gearbox (hydraulics), which leads to damage to the TCU’s sensors.

@HellaNooBs 5 ай бұрын

Get the OEM sensors