LOoks to me, like it would have been easier to cast large bricks out of the concrete and wet stacked them with mortar. All this post build work would be unnecessary.....i'm not convinced...
@SteveAddis20 сағат бұрын
Thanks for the comment. I have not cast concrete bricks at least yet or done mortar work. Cast bricks are solid for certain. Two extra steps compared to simply stacking like I did. I like a wall that can pass water through and not hold it back.
@SUCHKAALENA2 күн бұрын
Beautiful! How tall is this wall and how long is rebar? Should rebar go though the length to the bottom? How often to add rebar between each one?
@SteveAddis20 сағат бұрын
Thanks. Height is a 3-4 feet tall, supporting a little over 3 feet of stone to the backside. Rebar is various lengths as needed between 1 to 4 feet. Some sections full length, others just bridging. There should be rebar linking all bags, maximum two per bag to bridge and join. Thanks for the question!
@ecuadordave80766 күн бұрын
Great video. I am planning on a similar in the future so liked to see the how to tips and tricks.
@SteveAddis6 күн бұрын
@ecuadordave8076 That sounds good. I hope it turns out well for you. Take care!
@ryhol54178 күн бұрын
You’re probably going to need a few layers more.
@SteveAddis8 күн бұрын
Thanks for the input and comment!
@diameadozen10 күн бұрын
If you get a crack just fill it with cement
@SteveAddis9 күн бұрын
Thanks for the advice. Have a good weekend!
@mnmike688411 күн бұрын
How does cost compare per square foot for bags versus precast blocks? Didn’t show how to ensure full coverage on front bag edge. Did you tie the horizontal and vertical rebar? What effect.does the two paper layers have on bonding the rows together?
@SteveAddis11 күн бұрын
@mnmike6884 - It was less at the time doing this at about $1.85 a bag. Watch my improvements video to find out more details. No ties for rebar. Very few horizontals. Mostly verticals. The paper prevents true bonds. Where you punch holes through with the rods, it does connect at those points. Thanks for the comment. kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@YOUR-WORD-IS-YOUR-BOND12 күн бұрын
Cool
@SteveAddis12 күн бұрын
Thanks for the comment! Take care.
@YOUR-WORD-IS-YOUR-BOND14 күн бұрын
That's nice!
@SteveAddis12 күн бұрын
Thanks for your comment!
@benmiller335821 күн бұрын
Did you tie the horizontal and vertical rebar together in the curved section of the wall?
@SteveAddis20 күн бұрын
They were touching, yet not actually tied. Those horizontals were only to lock the courses and not connect. Thanks for the question.
@StarrGod69622 күн бұрын
This was a great idea, but the video sucks…. :/
@SteveAddis21 күн бұрын
Roger that. Thanks for watching!
@mrlariata929025 күн бұрын
Great idea I need to build a 2 foot wall because they had 4x4 timbers. I think I’ll go with these bags instead. Any suggestions of how deep you need to go with concrete bags for 2 feet for example, if you build a 6 foot fence it’s always best to go 2 to 3 feet deep. Is there the same concept for building walls with concrete bags?
@SteveAddis24 күн бұрын
@mrlariata9290 - Yes, all the timbers even railroad ties eventually decay when in contact with the ground at my place. 2 feet is a short wall. Depending on the soil, if it is soft, dig down to stable soils or compact it if needed, place stone base, compact. I would at least go down one course height if not more to be on the safe side. Lots of drainage behind it. Build it similar to other wall types. Watch my improvements video to get the best results. Thanks for the comment!
@mrlariata929024 күн бұрын
@@SteveAddis Thank you for the feedback.
@SteveAddis22 күн бұрын
@mrlariata9290 - You are welcome! Wish you success.
@smeargut180926 күн бұрын
free firewood
@SteveAddis24 күн бұрын
Yes, I guess it is! So much wood around here I never thought of that. Cut it up and let it float away. I still see parts still way down stream when I walk down the branch on a nice day. Lots of free rocks wash up here too!
@chrisyates157427 күн бұрын
crumble in 5 yrs
@SteveAddis24 күн бұрын
@chrisyates1574 - Don't know about that 5th year. Third year and it still looks the same in my followup videos. Thanks for your input! kzfaq.info/get/bejne/nKqbnZiYvZaxcZ8.html
@devon907528 күн бұрын
Rebar was a good idea to tie the sacks together. I'm afraid that without any geogrid and with how narrow the coarse aggregate behind the wall is this wall will want to tip really badly, especially with no improvement to the subgrade. It looks like this was uploaded quite a while ago, how has it performed so far?
@SteveAddis28 күн бұрын
Yes, I see what your are saying. I thought about the long end tipping in. Yet it is doubtful it will tip out because of the curvature and the solid clay behind it does not move. I was so tired of digging it out due to that hard clay factor. Yes, I would have put in geogrid or tiebacks like you said, if it were soft soil. The stone is minimal and only drains behind it. It might have used more stone. So far it has not changed and seems to be draining very well. It has a french drain in front of it. If it were to change, I would post it for sure and let you know. Thanks for your good input! Take care.
@smeargut1809Ай бұрын
Such a good idea, and you can use different color cement bags like white, I love it.
@SteveAddisАй бұрын
Thanks for your comment. Most were grey yet some were brown. Yet it was unknown until later when the paper was off.
@smirking8457Ай бұрын
Looks great. Is there anyway to treat the concrete to help it last longer?
@SteveAddisАй бұрын
You can always coat it with liquid concrete as I did at the base. A few comments said they saw this done before lasting over 30 years and more. I planned to stain seal with color later. Please watch this video and it explains what I did on the third wall. Thanks for the question! kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@SteveAddisАй бұрын
@smirking8457 - I don't know of a treatment other than coating it with liquid concrete as I did in the lower areas. I was considering a sealer stain combination. They hold up well. Here is the video that might give you some ideas. Thanks for the question. kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@giii7599Ай бұрын
If you only went 2 to 3 feet high would you use rebar?
@SteveAddisАй бұрын
Hi. I might not for a low wall. Things to consider: Is it affected by moving water flow such as a stream. Is it prone to vandals removing what you built. Does it support a soft or often wet soil behind it. Do you want it to be permanent or non permanent. Non permanent, lock it with rebar between the bags forming keys in some areas. Thanks for your comment.
@giii7599Ай бұрын
@@SteveAddis How did you handle rebar if you have to stop for a few days?
@SteveAddisАй бұрын
@giii7599 - I would always leave the rebar sticking up so that the rebar was bridged when I started again. I did not worry about connecting the rebar, just bridging the bags every where and using the longest when possible. Please see this video I made to help you you ideas of what I did. Take care! kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@jon_dough_gets_itАй бұрын
@STEVEADDIS great lets talk, can we do a quick call for tips and tricks, this is awesome
@SteveAddisАй бұрын
@jon_dough_gets_it - Yes we can sometime. I need to put a contact form on my website soon. I don't post numbers on YT as of yet. Did you happen to watch my improvements video and the updates videos? This video has most of the tips that I did not address in the previous videos. If you are doing walls like this, I would like to know your ideas or thoughts as well. Thank you much for watching. www.stevenaddis.com -Improvements & Methods: kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@jon_dough_gets_itАй бұрын
@SteveAddis yes after watching this I found your improvements video, very helpful! This tips and tricks answered most of my questions. Awesome videos brother!
@SteveAddisАй бұрын
That is good. If you have any more questions, just let me know. I should add it to the future list. Thanks!
@claytonsimplot9554Ай бұрын
How do you mix the bags. Just turn them end over end or flip the bag side to side?
@SteveAddisАй бұрын
Yes, that is basically how I do it. Usually from the factory it is mixed fairly well in the process of combining, yet aggregate will settle in spots. So mix them well, rolling and end to end. It just take a lot more time for sure. Tape the bags on the top at stopping points. Good question. Thank you for your comment.
@roths7Ай бұрын
I actually love this look. You did a great job. This was done at our city park, along a runoff creek at least 30 years ago....and it's still in great shape. Could you tell me how mch a pallet of this cost? and how many pallets(and how many bags are there per pallet) did you actually end up using? Lastly, what was the overall length of the wall you built?
@SteveAddisАй бұрын
Thanks. Good to hear that they hold. I heard the same from other comments. I believe 70 to a pallet, and if I recall 512 bags. The wall was about 70 feet. In the description I places some information. Be sure to watch the improvements video if you do it. The walls are better made now. Take care. $947.20- (512 Bags x $1.85)+(Rebar & Taxes)(Currently $3.04/bag QTY 70 at Lowe's.)(This was by volume and with discounts and prices may vary.)
@adelaferreira4575Ай бұрын
I am reading some of the comments and I wonder what a professional would say about this,in my opinion ,if you have a ton of money to spare ,go ahead and improvise ,but it doesn’t look like it will hold like a block or rock retaining wall,concrete works well when mixed with water as you use it ,but I may be wrong…
@SteveAddisАй бұрын
You make a good point.Thanks for the input. For myself: My cost being less than 1k US dollars was not a ton of money. Labor was free, what some do in the gym. Most past comments regarding price were similar to yours, yet some said for sure this saved thousands and this might have cost 15K or more. My cousin and uncle and previous generation are in the concrete business told me I saved a fortune on my head wall build. Now, concrete bag prices are up, yet so would yards of concrete, forms and such. So, yes definitely count the cost. I needed my culvert wall done because I was tired of the washouts. And, at the time of these builds contractors were too busy in my area. Then I thought, why not do the wall the same way. Though not perfect, this was the result having learned more from this wall when doing the next as shown in my three year update video. Again, thank you for the comment! Take care. Steve
@SteveAddisАй бұрын
Another good point you made for sure. On the point of this wall holding as well as as block, rock or concrete. It is not as durable as mixed concrete, yet it easily beats block or retaining wall blocks in mass, density and structure. I cut corners on tiebacks, so it is not perfect. Yet I am sitting on a hard clay hill that will never move in my lifetime. A couple of KZfaq comments were made that the person has noted that these walls are still standing well after 40 years. Thanks again for your input and comment. Food for thought. Take care!
@roths7Ай бұрын
@@SteveAddis Our city did this to a runoff tiny creek at least 30 years ago. It's still looks good and is going strong
@SteveAddisАй бұрын
That is good to hear. Thanks for the info!
@unfortunately_mortalАй бұрын
looks good
@SteveAddisАй бұрын
Thanks. It did turn out good. Not really planned, just turned out this way.
@vica153Ай бұрын
Culvert wall definitely did its job. Looks like you need to do a small section of concrete for the driveway above the culvert, so when it overflows the water simply goes over the top and doesn't damage anything.
@SteveAddisАй бұрын
Thanks. Yes you are correct. For now I placed geofabric and rip rap over that area on top a layer of 53 mix that washed away. Thanks for your input and comment!
@vica153Ай бұрын
I think the bags look better than standard formed wall, but your install is so thorough its almost as much work as doing standard concrete forms and you can get inserts to make the formed walls look like rocks. The bag walls are holding up ok after a few years, but you can see cracking/crumbling already. Have you thought about spray some sort of sealant on the exterior to keep it from crumbling as quickly? This seems like a method that is fine for small projects, but not ideal for larger walls.
@SteveAddisАй бұрын
Yes you are right it could have been formed. At the time no contractors were available. Yes I thought of that. I did coat the bottom area. Now most of the cracks were formed in the process of bags stretching. I tape them now as in the enclosed improvements video. Some commenters said that they have these walls doing fine after 40 years. Yet we will see. Thanks for your input on it. Take care! - Improvements: kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@chesterschzckАй бұрын
Working on one now
@SteveAddisАй бұрын
That sounds good. Saved a lot of money and did it the way I wanted it. Did you watch the improvements video? Just in case you need the link: kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@FrenchConnectieАй бұрын
Thanks again Steve! 💪.....
@SteveAddisАй бұрын
You are welcome @FrenchConnectie! - Take care.
@tactical-crashАй бұрын
No idea why this was in recommended but good job. Now I want to see a project on diverting water from sides into the first culvert (3:50). Kinda looked like the road would be washed out quicker at the moment with the amount of water.
@SteveAddisАй бұрын
Thanks for your comment. It is close to the road.
@mnniceguy2011Ай бұрын
can you remove the stupid music?
@SteveAddisАй бұрын
Yes, that would be a silent version. Like the old films. I will do that on another video. :)
@clsanchez77Ай бұрын
Thank you for showing this with PVC. Seriously. Digging a French drain and hauling rock is a lot of work and I get angry when I see people go through all of this effort and then use the stupid corrugated and perforated black flex pipe. You do not need the top holes; 2-holes at the 8 and 4 positions is adequate. Also, would have put cleanouts on both lines. Finally, your sanitary tee looks like it was installed backwards, but should not make a difference for this application. 3:40 now that is a properly sized culvert. If this is on your property, do yourself a major favor and place some rock on both sides of the pipe, and both on the upstream and downstream discharge ends of the embankment. The soil holding your embankment will thank you later. 6:00 that little hydraulic jump at the entrance of the metal culvert tells me you have a turbulence issue at the head and can result in erosion beneath the culvert. Can't tell with the water, but if this is not rock armored under the pipe, please do so. Very beautiful wall and would hate to see it undermined. I would go 18" deep with a mix of 9" to 15" rock. As an alternate you could also do an apron with the concrete backs to match your wall.
@SteveAddisАй бұрын
Thank you for this great information and input! I will consider these options and possibilities. Always good to have an experienced second person observation.
@Mr.cookie789Ай бұрын
Absolutely the best quality! Amazing
@SteveAddisАй бұрын
Hey, thanks! I tried to cover the bases on this one. Forgot to show the critter screen on the exit pipe. I might have gone deeper, yet I did not want the creek backing up in it.
@justsain3236Ай бұрын
why does the pipe have holes in the top; surely you'd want the on the bottom at an angle.
@SteveAddisАй бұрын
Hi. It's a three hole pipe. Two are at the bottom. 8 and 4 o clock positions. Thanks for the comment!
@SteveAddisАй бұрын
This shows the pipe description used in another video. Thanks. kzfaq.info/get/bejne/jr11lqaIkqzRZYU.html
@aaronbaron3155Ай бұрын
This is quality. Shows everything without someone yakking😊
@SteveAddisАй бұрын
Thanks - Should have included the end pipe protector. Take care. :)
@drumswest5035Ай бұрын
How do you ensure the concrete is properly mixed to achieve its psi strength, or are you just relying on the dead weight of the bag?
@SteveAddisАй бұрын
The only thing you can do is mix the bags by rolling them end to end side to side, just in case the mixture is separated. It will never be the PSI strength of a true slump pour. Dead weight is a plus compared to some landscape block that is porous. Hopefully through continuing hydration over future years will produce formation of hydrated calcium silicate crystals which continue to grow binding, interlocking, filling particulate thus further strengthening of the concrete at a slow rate over time.
@wb3603Ай бұрын
im looking at doing this on a smaller scale, how is it holding up?
@SteveAddisАй бұрын
Doing very well. Have not touched it. I have a three year update video. This video might be give some tips or suggestions before you start. Wish you much success! kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@Big0verallsАй бұрын
Has anyone tried this same method as a pathway? I have to get across a small ravine to be able to access our back pasture that we can no longer access because the adjacent property that was family property for over a hundred years has been sold. I was thinking of having one layer five bags wide to get a width of 8’ (actually 95”)and then like 48’ long. It would be four pallets I believe if 42 bags is a full pallet. Then driving say 4’ of 1/2 rebar through each bag or at least the outside bags into the soil to keep it from washing away. Which I don’t really think it would but my brother in law is afraid it would. Just looking for a good way to make access that won’t break the bank.
@SteveAddisАй бұрын
I am not sure of what you are attempting. Yet I have a couple of similar situations with intermittent streams I wish to cross with a mower without building a bridge. Sometimes it get a major wash that would go over a bridge, yet most of the time it sets idle. My plan: The upstream will be dug down to not allow the flow to undercut and compromise it all. The exit will angle down and be dug down as well, so as not to be back cut by the wash. Place geofabric down then bags. Hopefully rock and soil deposition in the front will protect it from undercut. Streams change and unless it is a straight run, it may not do the job depending those changes. Eventually the rebar might rust away, yet there is basalt and fiberglass rebar available. Steel rebar will handle rocky soil better. I will be placing rebar in the sides of the bags to lock them together, forming a offset grid pattern. Hope you have success.
@MrZambrano101Ай бұрын
People in Oaxaca, Mexico build houses using this technique. 😅 Build an entire 3 bedroom, 2 bathroom, plus living room, kitchen, and garage for under $15k....
@SteveAddisАй бұрын
@MrZambrano101 I would would like to see that. Interesting. Thanks for posting this comment!
@godfreydebouillon88072 ай бұрын
Hi, thanks for the info! Hoe does the cement get wettened in the bag? Is it strong enough doing it this way?
@SteveAddis2 ай бұрын
You are welcome. I water them gradually, then when they set some, then water again. Once they set, I keep them wet for a few days. Paper bags stretch and sometimes this allows the top bags to form separation cracks, so tape the bags to prevent this stretching to hold the paper form. They seem to be getting stronger as time goes on. Watch this for more explanation. kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@Archangel-pd1rn2 ай бұрын
And thus Machu Picchu walls were made...
@SteveAddis2 ай бұрын
Those walls are really wonders of this world. kzfaq.info/get/bejne/ZryIZ7SnmtvUlXk.html
@ShawnRector2 ай бұрын
You could’ve done it way cheaper if you would’ve just gone to a concrete plant, they have molds at the concrete plant where they dump the extra concrete after the day or after the trip into a mold, making a block and then they sell those concrete blocks for dirt cheap… incredibly dumb video
@SteveAddis2 ай бұрын
@ShawnRector Thank you for the information. I need to check that out. Yet this only cost me less than 1K. Thanks :)
@captainkayakdiver66932 ай бұрын
What is the update of your concrete bag project? Is it holding up well?
@SteveAddis2 ай бұрын
Holding up well. I left it as is to see how it would do freeze thaw cycles. Here is the status playlist for you if you want to watch. Take care. kzfaq.info/sun/PL9Umhla0HdWIQzpyjblVRyG2cj7XSCs5Z
@user-oc7uq8ue7t2 ай бұрын
Thanks joe.
@SteveAddis2 ай бұрын
You are very welcome!
@joestrait62912 ай бұрын
Dam wish I'd seen this a year ago! I have the same thing but had a wall poured and cost me lots the wall is cracked and missed shaped like yours way better!
@SteveAddis2 ай бұрын
Thanks for comment. Sorry to hear. - I guess a commercial level wall pour (not thin wall) works. You have no idea how many contractors laughed at my builds with all their thoughts without ever having done this. Been done for many years / decades ago and still holding. It is no laughing matter when when you pay the contractor 20 times my cost. :)
@lieblee30632 ай бұрын
Can I do this for my seawall by the lake?
@SteveAddis2 ай бұрын
I am not sure. I will use it on a creek (with cloth behind it) to attempt to prevent it from taking out a trail, on a curve. I may be okay, because I do see blue clay in the bottom of the creek. Yet the concern is it gets undercut or back cut. So the bottom and ends need to be back set to prevent this. Do your research and look how sea/lake walls are designed and think it through very well.
@melindakantner92023 ай бұрын
Are all bags laid side to side, do any bags run front to back? How long are the sections of rebar and is it 2 rods of rebar per bag? You do phenomenal work! I subscribed! Thank you for your videos.
@SteveAddis3 ай бұрын
Hi. Side to side vs front to back depends if you do setbacks. The culvert wall I did both to interlock them, especially on the top of the culvert 80lb bags were used to overlap two 50lb bags locking the rebar. I tried to use 3.5ft to 4ft rebar on the wall and longer on the culvert. Two rebar per bag locking like legos. Thank you for your kind words and for the sub! It was a pleasure to do the vids. Take care.
@jayviz3 ай бұрын
How does your back feel?
@SteveAddis3 ай бұрын
Lol. Pretty good thankfully. It was not built in a day for sure! Lift properly and carry at the waist, makes it a little easier.
@ronaldphillips87503 ай бұрын
How long does it take to set up?
@SteveAddis3 ай бұрын
Over night, then keep it wet for a while, and rain will also help.
@ronaldphillips87503 ай бұрын
@@SteveAddis Thanks for the reply and doing the video.
@justsaying55493 ай бұрын
How do I drive the rebar into the bags?
@SteveAddis3 ай бұрын
I used sledge hammers. Good question.
@Taylorina8X4 ай бұрын
When doing this method does it all have to be done in one shot or can it slowly be added on in segments?
@SteveAddis4 ай бұрын
Segments best for large wall so bags do not stretch too much. Please see this vid. Thanks for your question. kzfaq.info/get/bejne/qruclpSCx5ulZ2g.html
@kristymissy59804 ай бұрын
What kind of bagged cement do you recommend? Quick set or regular?
@SteveAddis4 ай бұрын
The lowest cost which is likely ready mix, purchased bulk to save cost.