What is the dimensions of the cord ?thickness wise thanks

Since when did engineers forget screws exist.

Awesome

One week after replacing the battery it becomes the same as before.

Torque Specs?

Thank you. For $40 I can try to salvage an otherwise great pair of buds rather than buying a new pair and making more e-waste.

Thanks a lot. Great video

I managed to break the flat cable while removing the old battery. Did I permanently damage my headphones?

I have a craftsman 917.255520 I can’t find what aftermarket belt should be used 38” deck

7:50 as others have pointed out, don't don't do that, you risk breaking the ribbon (as I did...). You can just remove the battery without disconnecting that ribbon anyway. Hope my failure helps someone at least.

Most of the assemblies will come out with the removal of the four bolts on each side holding the steering assembly in place. Much easier splitting the assembly on the ground and reinstalling the entire thing back. Hard on the back working as you did. Also did you check the bushings on the turning bracket? Much easier to replace off the tractor. Grease is the key to keeping the steering working. The torn part of the old assembly probably rusted onto the outside and just ripped the sheet metal apart.

Many thanks for this video! Was easy to do this way. And it fixed my problem!

Nice job.

Ribbon on mine broke when I tried to disconnect from the circuit board. There was some glue attached to it near the 45 degree turn. Headphones still worked with about 30 minutes per ear, but definitely one is garbage now. I would advise to gently detach the ribbon from the glue somehow first, then attempt to disconnect the ribbon, as I think the glue is what did mine in. Edit: Fwiw, I read this ribbon controls ANC in full or partially, so the headphone will still work but will not support ANC.

Exactly what I needed to see. Thank you

Thanks for the video. I would like to add that you could separate the two halves enough to remove the battery without disconnecting the cables and you might have to lift the spring contacts slightly to establish positive contact with the replacement battery.

I have the ys4500 having trouble getting it on the last pulley any ideas???

Gasket flip if it still leaks is a good idea. Installed one this morning and same thing happened. Tons of videos showing no leaks after first install. Thanks for posting.

Thank you! earned a sub!

nah i ain't doing that. i just bought an iem and call it a day

Excellent

And let me also add that my earbuds were out of warranty. This was a problem from Sony. It was caused by an update they did to the buds that caused this problem so they fixed it even out of warranty.

So much technology in these little things. It's amazing. I love my wf-1000xm4. Had them for almost 2 year's.

Anybody that has the first line of the wf-1000xm4 will probably have the issue. Contact Sony and explain the problem. They WILL help you .

I just got mine back from New York from repair. They are working as they were New again. Sony shipped to and from and fixed for free. A downloaded update caused this issue of not holding a charge for more that 5 minutes each side. Sony took care of the problem for me. Thanks for the vids

i was literally holding my breath lol nice job

Just buy a new one, they are pretty cheaper

Thanks for the video. My left earbud has recently stopped working - any idea how I can work out whether it's the earbud itself or the case before I start taking the earbud apart?

So, after watching a couple of these videos I noticed that they put a lot of extra cord in the umbrella. So, I decided to start by checking the top end of the umbrella to see if the cord was still accessible there - and yes it was! At the very top, over the pulley, I could see the cord still there. So I turned the crank and loosened the cord more to allow me to pull the cord out further to push more of it into the end. I had to fish it back through the end cap (as I had to glue it in place a while ago because it kept slipping off and that's how the cord got abraded in the first place). I just used a crochet hook - worked like a charm. Then all I needed to do was pop the end button off, remove the broken piece and replace it with the end of the remaining cord. Thank you for this video! You saved me a lot of time, frustration - and money!!

Mine just got water damage? What can I do?

whats that daisy chain of bolt size check kit you have?

The magnet below the battery fell off and stuck with the battery, what should i do

Not sure that was particularly helpful. At the beginning it was a whirlwind of pulling clips of pins. But, which clips, which pins. Eventually it seemed you have to remove the mower deck, but that was not obvious!

One of my turn signals fell off and I have two wires hanging out. I bought a new set that has two wires with bullet connections. I just wrapped the wires around the bullet connections and nothing happened. Do I need to put a bullet connector on the wires? The other side turn signal is working so I don’t think it’s a bad switch. Thank You for any advice.

Fantastic video - I was able to use my cooking hob instead of a heat gun to open the case and detach the board from the battery

Sony is such a shit company to not take responsibility for this failed product. I hate that I spend $300 and was only able to use it for a year.

i just replaced my batteries i think i did it right thanks for the instructions

Just put a new one on

you could have used that vice to close the washer around the ball joint and then just smacked the top of the ball joint while the vice supported the washer. Not a good idea though as the washer is a thin piece and it will wailer out fast.

Thank you. I didn't want to risk it using a heat gun, so I just used a razor blade to cut the adhesive on the case. I think it could be done without removing the ribbon cable there's enough slack.

Replacing batteries with a new one will resolve the draining issue? As some users have complained the issue still persist may be a motherboard causing draining issue

They refused to provide a free kit. They charged me $49.50 plus shipping. My set was only about three years old and cost over $300. One would think this company would be responsible for their inferior mechanism.

Can you just disconnect this to stop it from clicking if you don’t have the turn signals hooked up?

Same problem here .. no Sony anymore

Was this the fix you did after you put the new blinkers on the back and it started solid without blinking. Cause that's what happened to mine. I put new blinkers on the back and now they're all solid. I'll try a new relay.

Did you ever fix the issue of them not blinking? I'm putting on aftermarket taillights. And having the same exact issue that stays solid. Did you ever figure it out? If so, please let me know, is it just replacing the relay?

Thank you very much. Definitely going to give a shot!!!

Awesome video. I've just repaired one of my earbuds with your tutorial. I'd just add a note to say to open the earbud after applying heat, I've applied pliers, VERY gently, pressing on the sides where the parts are glued, not on top of the main surfaces. That allowed it to have a slight opening from where I could slide through the rest and separate the parts. Put some fabric where the pliers are pressing to avoid marks on the surface of the plastic. All this very very gently and it's working as new. Thanks.

What exhaust does he have shoot

How do I know which wires go to the turn signals?