What if your using a 220 wire and you don't have a neutral wire
@AskTheElectrician3 күн бұрын
A 220Volt circuit may be protected against ground faults by installing a GFCI Circuit Breaker properly sized for the circuit wiring.
@SOCORROGM10 күн бұрын
Thanx 😊
@AskTheElectrician8 күн бұрын
Welcome 😊
@charliely971313 күн бұрын
Thank you very much.
@AskTheElectrician12 күн бұрын
You are welcome!
@anthonylawlor913014 күн бұрын
Nice .79 cent outlet!!!!!
@LIGHTEMUPELECTRIC18 күн бұрын
What if there is no joist?
@AskTheElectrician17 күн бұрын
Use a Spanner Bracket and Box to go between two joists, or install a a block of wood between two joists and install a shallow metal box.
@stephenly767120 күн бұрын
Thank you sir
@AskTheElectrician19 күн бұрын
Your Welcome!
@madellinevega331324 күн бұрын
does the hot black wire go into the load or line of the GFCI?
@AskTheElectrician23 күн бұрын
The Line side.
@pthomas578626 күн бұрын
If it's in a metal box can I ground it to the box
@AskTheElectrician24 күн бұрын
If the metal box is grounded with an approved ground source then yes, you could attach a ground wire to the grounded metal box.
@nyotauhura7412Ай бұрын
Thank you. I don't have a bare ground. I have a green ground. Your video is very informative. So much so that I have decided I need professional help.
@AskTheElectricianАй бұрын
Glad it was helpful!
@rrrr6863Ай бұрын
Wonderful explanation and practical examples given.
@artistledАй бұрын
@AskTheElectrician - I read that you can connect/add a ground wire from the receptical to a copper drain pipe, kinda like what you simulated in your video. Is that ok to do or dangerous and not advisable and against code?
@AskTheElectricianАй бұрын
Great Question! Attaching a ground wire using an approved ground strap to a continuous metallic cold water pipe that originates from a metallic cold water source, such as the water company, is one method of grounding a receptacle outlet in an older home.
@artistledАй бұрын
@AskTheElectrician thank you for your kind reply and confirming. Truly appreciated! 🙏🫶
@AskTheElectricianАй бұрын
Your Very Welcome - Have a Great Day!
@irvingrabinАй бұрын
Hey, in your bathroom you got two pairs of wires. Most likely one of them is a line, another a load. You can easily check which is which and use GFCI to protect a load. Instead you connected them together. Which means that any short-circuit on the load outlets would go to the breakers, rather than being caught by GFCI itself.
@AskTheElectricianАй бұрын
Yes, that is One example of how an outlet circuit may be wired and have GFCI protection for one specific outlet.
@davidweber6024Ай бұрын
Why do HWH typically use bare wire connections with wire nuts vs a screw terminal (similar to a breaker)?
@AskTheElectricianАй бұрын
Good question! Maybe because it would cost more?
@davidweber6024Ай бұрын
@@AskTheElectricianthank you for taking the time to reply to my question. This baffles me especially if you follow the supplied wires in the junction box of the hot water heater down about 18” to where they screw down to a terminal at the upper element/thermostat. Seems as tho you could eliminate an extra splice by running the 10/2 right to the terminal. The most convenient would be a nice terminal block in the upper built-in compartment of the water heater, but like you said… it would add a little extra cost. Personally… I would find it well worth the money.
@davidweber6024Ай бұрын
@@AskTheElectrician I asked a buddy of mine that is an E 1 and his only explanation was the cost factor as well.
@cqueen7739Ай бұрын
I removed 2 hallway light fixtures in my hallway. Each had a single- light bulb. I replaced each of them with a double light bulb in the fixture. I turned on the power and the light will not turn on. There is power running from the hot wires and the light switch. I'm not sure why the light is not coming on. Please help
@AskTheElectricianАй бұрын
The wiring connections should be checked.
@sobercrimson4659Ай бұрын
Is that the proper rotation?! Honest question
@AskTheElectricianАй бұрын
Rotation?
@extinctjedi3658Ай бұрын
Is it normal for the water heater to have 12 gague wires that hook up to 10 gauge power wires? I'm stuck at this step, I'm switching from a gas water heater and using a former ac power line that is 10-2 wire from a dual 30 Amp breaker. It feels strange to me that the water heater has 12 gauge wire to meet my 10 gauge. Is this normal?
@AskTheElectricianАй бұрын
#10 gauge wire should be used for a 30amp circuit.
@Dr.M.VincentCurleyАй бұрын
You go ON AND ON about irrelevant things. Just say, Do this, or DON'T DO THIS, don't just keep giving reason after reason. Aside what you might believe, most of us are smart enough to understand the REASONS why to do or not to do something, stick to the facts so we can get through this and other videos so we can get a full encompassment of what this task entails.
@AskTheElectricianАй бұрын
Thanks for this - but keep in mind that not everyone has the same level of knowledge or understanding out here, therefor I try to explain as I go, and actually it has works out very well. But Thanks just the same, I will keep this in mind!
@VOLTRONDEFENDER44402 ай бұрын
You could stil use a gfci for non wet environments it will still provide protection
@AskTheElectricianАй бұрын
Yes
@timmcnulty9852 ай бұрын
Can you convert a new 4 prong stove to the old 3 prong style. Mine comes through the floor and there are only 3 wires present.
@AskTheElectrician2 ай бұрын
It depends on the specific stove that you have. What does the Installation manual say.
@guillermogomez8652 ай бұрын
Wow , excellent video , well done explaining stet by step , I’m really impressed, well done
@AskTheElectrician2 ай бұрын
Thank you very much!
@BF-rn3oz3 ай бұрын
This video was excellent. Thank you so much!
@AskTheElectrician2 ай бұрын
Thank you for watching!
@lequang22963 ай бұрын
Crystal clear Thanks for sharing Like % Shared
@AskTheElectrician3 ай бұрын
Thanks for watching!
@dennisp43953 ай бұрын
I have a 240V dual element 28 gal tank. I have a line coming into it coded Black /white/ground. There is a red & black wire from the tank. Which color from the tank is connected to the black wire coming in, and the white wire coming in.
@AskTheElectrician3 ай бұрын
As noted in the video - when the incoming black and white are the 240volt wires, they connect to the black and red wires of the water heater, respectively.
@Victor-7794 ай бұрын
Thanks for the video. I know this may be a code question so mileage might vary. Running the wire from the ceiling to the tank, or alternately, from a junction box to the tank, does it have to be shielded with the metal tubing as you've shown or can we just run the wire as is, with plastic sheathing still on, right to the tank?
@AskTheElectrician3 ай бұрын
The wire should be protected using an approved method, typically metal flex and connectors.
@Victor-7793 ай бұрын
@@AskTheElectrician I'm going to use a liquid tight flexible plastic sheath, used for outdoor applications usually. I just don't like the idea of a metal sheathing for electricity.
@21847835gАй бұрын
@@AskTheElectricianA video by a self described inspector stated that BX is not appropriate. Is there another flexible metal jacketed type of product? I’ve seen a few websites that don’t offer much help in differentiating.
@domenicoramazzini82084 ай бұрын
Hi Dave - new subscriber... great videos and thanks for sharing your knowledge. I have a 240v line wired directly to an oven tower. Doing a little remodel and need to extend it so i can run it to a diferent location via the attic. The way i have done it in the past is by using the rught junction box, cliping, stripping and then joingin with wire nut, taping and securing wires in junction box, with ground wire to ground/green screw... Seems to work just fine, many places ive looked at say you should rewire from the whole line from fuse box. Whats your take? Im in Texas btw and ive looked at code and its a little confusing since home was built in 1979 Thanks in advance for your input.
@AskTheElectrician4 ай бұрын
If the splice is done according to code with the method and the approved components, then a splice would be fine.
@AbigailSanchez-kc6eh4 ай бұрын
Question. Disregarding the interlock switch,would it matter where the the generator breaker is installed? Say if you put it on the middle ,it will still power all circuits because thats how electricity flows ,essentially like water,correct?
@AskTheElectrician4 ай бұрын
Electricity works in both directions, regardless of the location of a circuit breaker. The concern when connecting a generator is to install a device that will turn off the utility power source before the generator power is turned turned on. An approved transfer device that is installed properly will ensure safety as required.
@AbigailSanchez-kc6eh4 ай бұрын
@@AskTheElectrician ah ok got it. Thanks for answering 😊
@MrMrremmington4 ай бұрын
Being that your is tutorial, you should have demonstrated connecting the wires into the back of the receptacle proper attachment, testing security that it doesn’t pop out just so people have a full description of how things are actually done.
@AskTheElectrician4 ай бұрын
Thanks for the tip
@GabrielSBarbaraS4 ай бұрын
How about a lockable disconnect close to the hot water tank. Is that required. ?
@AskTheElectrician4 ай бұрын
Personally I think a disconnect is a great idea, however since a typical water heater is a permanent installation with (almost) no parts to service, up to now the NEC does not require a disconnect.
@stevenv21904 ай бұрын
Should there be a disconnect on the wall near the water heater?
@AskTheElectrician4 ай бұрын
Personally I think there should be, however since a typical water heater is a permanent installation with (almost) no parts to service, up to now the NEC does not require a disconnect. Note that the newer hybrid water heaters may require a disconnect.
@rhess104 ай бұрын
Good stuff. Nice explanation. Your website isn't working though. I would love to download the guide you mentioned.
@AskTheElectrician4 ай бұрын
What happened? make sure the url you are using is correct: ask-the-electrician.com Hope to see you there.
@haerfgvbag70504 ай бұрын
Thank you brother
@AskTheElectrician4 ай бұрын
Your Welcome!
@sjorgezamarron35744 ай бұрын
This video is excellent, well explained... Thanks a lot...
@AskTheElectrician4 ай бұрын
You are most welcome
@johnmurphy96884 ай бұрын
Great video. Thanks for sharing your knowledge. Im learning
@AskTheElectrician4 ай бұрын
Glad to help
@onlyulee8665 ай бұрын
I'm not electrician if I have a motor call for 40 amps and at my breaker box it has 50 amps breaker can I just change the breaker to 40 amps breaker
@AskTheElectrician5 ай бұрын
What is the motor used for and what is the circuit wire size?
@onlyulee8665 ай бұрын
@@AskTheElectrician it's for the air handler I'm taking out the old ones. It has 8 kw with the breaker size 50 amps 6 awg wire .
@AskTheElectrician4 ай бұрын
The size of the breaker may be reduced to conform to the motor specifications.
@LIGHTEMUPELECTRIC18 күн бұрын
Yes, assuming the wire size is 8AWG
@raetrelinski5 ай бұрын
Can you use a GFCI switch/outlet combo with this wiring?
@AskTheElectrician5 ай бұрын
a Combo Switch Outlet will protect the same way, however it will only protect the single outlet.
@onlyulee8665 ай бұрын
What the breaker size for range. It call for 11.3kw
@Ioang405 ай бұрын
Great video! I have a question - I have a 3 wire dryer outlet ( 2 hot -white and black and 1 bare wire ) . My dryer(2016 model) has 4 prong cord. Would replacing the 4 wiire cord with 3 wire be acceptable for my dryer ?Will it cause any problems? Thank you !!
@AskTheElectrician5 ай бұрын
You can only use a 3-wire cord if the dryer manufacturers manual states that you can, otherwise it will require a 4-wire cord.
@ronlytel28215 ай бұрын
I have a situation where 4 ungrounded outlets are in a series. Do I need to put a gfci in every recip box, or just the first one?
@kjon99fm5 ай бұрын
How does one verify which wire is hot and which one is neutral (using a multimeter)? Also...if you don't want to GFCI protect any outlets downline, you wire the GFCI with line and load wires into the line terminals in the back of the GFCI outlet only?
@AskTheElectrician5 ай бұрын
Wiring may be verified using a voltage tester with one lead attached to a grounded source, such as a grounded outlet box or switch box, or a continuous metal water pipe, then testing the wiring to see if one has voltage. Yes - if GFCI protection is not needed for downstream outlets, then the wiring you have described should be connected to the Line side of the GFCI.
@kjon99fm5 ай бұрын
Thank you!@@AskTheElectrician
@stephshome70495 ай бұрын
What if all outlets in the home are 2 prong with no ground? Is there a way to fix this without having to rewire?
@AskTheElectrician5 ай бұрын
Yes - If a ground wire is needed for a grounded appliance cord then a ground wire may be installed to a copper or galvanized water pipe that is in the same location, using an approved ground clamp. Otherwise continue to use the two prong outlets. Install GFCI Outlets where they are required even if there is no ground wire available - they still work and are code compliant.
@84751431175 ай бұрын
I HATE older homes like the one I grew up in with NO grounding...
@AskTheElectrician5 ай бұрын
They just need a little TLC and upgrades to make them great again!
@cavsnake136 ай бұрын
thank you!
@erikhamann5416 ай бұрын
Really nice video with clear pictures and explanations, I can’t wait for another project so I can see another video as good as yours! Thank you
@josephuspetaway3576 ай бұрын
This is by far the best video I have reviewed for installing an electric water heater. Thanks.
@AskTheElectrician6 ай бұрын
Great to hear!
@mando17836 ай бұрын
Great video I have questions
@rigosandoval2826 ай бұрын
greats informacion o please keep made more video .
@AskTheElectrician6 ай бұрын
Thank you - I am making more videos for you!
@randychilders63666 ай бұрын
Not sure of the format to formally ask a question, but here goes; Hi. I have a portable AC unit that is tripping the breaker. The breaker has "15" on it so I assume it's a 15 Amp breaker. The AC unit has a specs sticker and states: Current Consumption is 10.8 A. Besides the AC unit, there's a laptop and ceiling fan running. Is it as simple as replacing the breakers with a 20 Amp breaker?
@Imsierrabound6 ай бұрын
Some older homes from the 50’s and 60’s have a shared ground wire running to the bathrooms and kitchen, but the ground is combined with the neutrals in the sub-panel (sub-panels of this vintage typically did not have a ground running to the main panel). I’d say in this case it’s OK to use the ground wire when adding a GFCI outlet and the homeowner should consider a sub-panel upgrade or add a bonded ground bar in the sub-panel with a ground running to the main or metal water pipe (main panel of this vintage were typically grounded to the water pipe entering the home).
@andrewtoth98766 ай бұрын
Thank you. You are very good at covering salient points related to the GFCI. I just protected my family with your assistance. Bless you!
@AskTheElectrician6 ай бұрын
Thank You - I'm Glad it was helpful for you and your family!