it's just a phone camera behind a laser rangefinder.

Wolf advantages over F2: + ridiculously air efficient; + nozzle with no wobble; + you can easily fine tune the nozzle length; + adjustable speed of the nozzle forward movement (bb loading force); + nozzle & poppet movement timings doesn't depend at all on input air pressure, your engine will perform in the same way on 50 PSI and on 120 PSI; + different gun profiles in FCU with easy switch between your CQB, assault or DMR roles; + magnetic trigger and optical selector sensor (no fragile microswitches); + lower sound profile. ------------------------------------------------------------------------------------------- F2 advantages over Wolf: + cheaper than Wolf; + cheap and accessible spare parts - trigger board, FCU (P* TB - 30 EUR, FCU - 90 EUR, Wolf TB+FCU - 230 EUR, Programming unit - 85 EUR); + you can mount it in gearbox shells other than V2; + you can use it with bluetooth FCUs like Gorilla or Gate Titan II HPA. Performance wise there's no significant differences. They both shoot great.

@@NikolayDimitrovFisher Thanks!

Hi. No, no PTFE tape mod is needed. The white delrin nozzle isn't crucial, you can use the stock black v1 nozzle. The only mod needed is sanding down a 0.1 mm from the Flamingo lips because it's 15.5 mm long and ML Wonder that was used in MGW design is 15.4 mm. That's all.

If you have an old gen Prommy EG - get a black Begadi SHP5 (70°) or blue (Super) Macaron and use the hard concave nub with Maxx.

@@NikolayDimitrovFisher great! i dont know if my promy barrel its the old gen, but its EG for sure, i can find the super macaron blue, and the hard concave nub, you mean the metal one right?. i case of buying a craze yet maple leaf inner, what do you recomende me? (for the same build, F2, max model hop up and DMR build) thanbk you so much for the response!

@@TorksTube yes, exactly.

@@NikolayDimitrovFisher hello again brother!, i just bough a Rhop for my prommy inner 6.03mm, what bucking did you recomend me and what nub? i have the maxx model hop up and retroarms too, or you are still prefering the super macaron with the hard concave nub? thanks!!

@@TorksTube best bucking for R-hoped Prommy is flathoped Madbul Shark (red). For nub - the preinstalled 4 mm soft orange M-nub in Maxx.

The MTW is on a bench rest. There’s no movement. I prefer to test outside because I play only outdoor.

I can see the movement of the rifle in ur scope cam. And u dismounted the rifle for changing the Hopupunit. So what are u telling me?

@@stephger1925 with 35 mm lens every insignificant move is amplified in scope cam frames. Even the vibrations from shots. This is not a lab test. But for my purpose it's more than enough.

@@stephger1925 Why the criticism? I rather see testing in normal conditions. I use the Alpha with super MR 70 and black nub without R-hop in the standard MTW barrel. This weekend with 0.30 BB shooting arround 60m with out any issue. Do thinking of upgrading the barrel to a PDI 6.08

Yes, you need to cut the side wing of the bucking. The hopup works really well with ML Wonder or R-hop like GBB buckings.

No. It requires a unbridged barrel with AEG side cuts for the C-clip like Maple Leaf Crazy Jet, ML hybrid barrels or Stalker Morpheus. And it works only with GBB buckings.

@@NikolayDimitrovFisher would you recommend a stalker morpheus and gbb soft bucking over a silent industries with soft bucking aeg?

@@danielarturodebernardogome832 in my MTW Maxx MGW with Stalker Morpheus and Stalker R-hop patch and sleeve bucking (or Flamingo) works better than any regular AEG bucking. I avoid recommending anything. I prefer to post my results and let everyone decide for themselves if they like them and would like to try something similar in their replica.

@@NikolayDimitrovFisher have been trying lately the 4UANTUM new aeg bucking. Getting pretty good results 7x7 cm grouping at 30M. Will be for sure trying what you told me, as I already have the m4g…

You can order it from McMaster - www.mcmaster.com/5109K31/ and cut the piece you need. And you have to modify the stock arm to glue the nub. It's the same nub that comes pre-installed in Maxx M4W/MXW/MGW. photos.app.goo.gl/9HY1Dyf29rvGNHLQ9 photos.app.goo.gl/HdRde2W1tG9tTpPi9

FPS and accuracy wise - it's slightly better than M4E.

@@NikolayDimitrovFisher is it a noticable difference like you see it when shooting, you see it with a chrono or how much?

@@marcoviebrock1550 i wouldn't say it's noticeable that much to substantiate spending 90 EUR for it if you already have a good working combo. Definitely M4G shows more consistent FPS readings on chrono. Also with M4G and GBB buckings you have more predictable and flatter shots. IMHO the only AEG hopup combo that can compete with M4G is R-hoped barrel with flathoped Madbull 'red' in M4E. But R-hop is PITA for install and fine tuning.

On this field there's no MED for up to 1.7 J and most of the engagements are on 20-30 meters. 0.32s are more than enough for this.

@@NikolayDimitrovFishercan you do a gameplay with the silent hop aeg I really want to see what it’s like

@@UTTPwillFAIL my next video will be with SI Alpha in this build.

@@NikolayDimitrovFisher thanks I’m hopefully gonna buy it soon

Redline SFR

Cool!!! ☺️👍

Yes. Not so good in applying consistent hop effect as the soft M-nub. I had too many random vertical flyers.

It's not actually an open bolt mode. More like an AEG mode - the F2 nozzle is forward biased and cycles to load the bb after the trigger pull. I can easily achieve consistent accuracy with Cbof and properly tuned dr (return to battery delay) setting since the hopups are designed to work with this mode.

I consider adding ENG subtitles in my future videos

So now I don’t know what to do. It’s not working. Trajectory must be laser at least 70 meters. It goes 40 and then goes wrong. Velocity stable

@@OleksiySynergy the trolley position in MGW/M4G hopups is aligned with the patch of the GBB bucking in unbridged barrel. The crucial things for accurate shots are the lips resistance (especially for HPA where the nozzle loads the bb with more force compared to the bolt action snipers), the consistent nub pressing and the consistent bb placing inside of the bucking before being fired.

Yes. Without cutting it you can't fit the bucking. And you need to sand a little from the X-Range lips so you can lock the C-clips. Modify bucking is ~16mm long. Maple Leaf buckings are 15.4 mm.

Yes. Without cutting it you can't fit the bucking.

@@NikolayDimitrovFisher did you install the small brass ring before putting the bucking in? I found it made it difficult to get the barrel clip on

The ring that comes with the hop up

@@acecustombuilds no, the brass ring is for Maple Leaf buckings. Flamingo is 15.5 mm, 0.1 mm longer than ML Wonder that was used in hopup design, so you may need to sand just a little bit from its lips if it's too difficult to lock the C-clip.

In my experience - the ability of M4P to be fine tuned to the nozzle length *and* magazine bb entry in wide variety of M4 receiver + not stock shell combos that are typical for custom HPA setups. Performance wise they're the same.

It's just a camera behind a laser range finder.

Phone camera behind a laser range finder.

It's not a tombstone nor a fallen heroes memorial.

@@NikolayDimitrovFisher so its still kinda disrespectfull then

@@BarrieBuskruitZV He literally says it's not a tombstone NOR a fallen heroes memorial. So it's just a stone with some text on it. Chill out.

I like it. It works pretty good with Flamingo, with Stalker SR-hop and Modify X-Range buckings and T.N-T TR-nub 70°.

Little silicon on bucking but be careful and keep it away from the lips. It will help bucking to slide effortlessly into the hopup.

I don't have ML MR 2023 GBB/VSR but i could use other good buckings. I'm thinking for a while about tests on 1.1 J. It would be interesting to see the results although I rarely play on our CQB fields and we're limited - we can use up to 0.30g bbs.

@@NikolayDimitrovFisher To be fair I'm in the UK so full auto limited is 1.1j while DMR is 1.88j and bolt actions are 2.32j so I was interested if the you could get the same range as DMR and bolt action on 1.1j with a heavy 0.48g bb. This is theoretically possible but would be nice if its true in the real world as well. On the bucking I wanted to know if the the Maxx unit can put in the GBB bucking that have the extra rubber sticking out like the Maple Leaf MR GBB/VSR bucking, or if you would have to shave it down, or it just doesn't fit as I cant find definitive answer even after asking Maxx directly as i would be looking to buy one if you can as the big flat r-hop on bridgeless barrels is amazing. Thank you in advance.

@@NikolayDimitrovFisher Update I will have the gun (MTW Unleased 7inch) very soon with the Maxx MGW, using Maple Leaf 220 mm Crazy Jet 6.04mm with the Maple Leaf MR 2023, using 0.48g bbs. I let you know how it goes after 20th July.

@@NikolayDimitrovFisher Managed to get my build done and tested on the 20th. MTW unleashed, Crazy jet barrel 220mm, MR Hop rubber 50 (green) VSR with the MAXX MGW Hop unit. Using 0.48g at 1.07j I was managing to get an effective range of 70m about max range of 80/85m on a non windy day.

@@aston4736 sounds very good. How was the accuracy?

What program?

I could make one in near future.

Honestly, i wouldn't spend 100+ EUR for a new barrel & bbs just for the sake of testing :)

Ако за всяка тежест на топчета АЕГ-то е с оптимално нагласен обем на цилиндрова група и цев - да.

Yes, also the same if you throw the bb at that speed with backspin :)

There's no doubt about that :) The question is "is the heavier bb slower than the lighter, all other things (joules) equal?"

Ye bro my friend had 80 more fps than me and I still had more range than him with .28s he’s using .20s at 350 fps and me at 275fps

@@UTTPwillFAILjoule wise it was just 1.15(0.2) vs 1J (0.28). No wonder the 0.28 were better :)

@@tatkoairsoft2146 no that’s not 1 joule it was 0.93

Both ML Crazy Jet and Hybrid barrels will work with Maxx MGW hopup.

Yep. R-hop is crucially dependent on bucking lips tension and nub softness and even pressure. With Alpha i have good shots trajectory only with 50° or softer nubs.

Yes. Better than Maple Leaf and on par with Flamingo, SR-hop or Modify X-Range.

Gbb or aeg you mean?

@@danielarturodebernardogome832 GBB one.

@@NikolayDimitrovFisher do you like aeg one?

@@danielarturodebernardogome832 Not really. It's not better than Maple Leaf buckings.

Flathoped Madbull 'red' or black Modify Baton Ryusoku.

MGW is a new Maxx hopup for Wolverine MTW that uses GBB buckings with hybrid barrels.

It's not mine. This guy owns it and did the conversion - www.youtube.com/@milennikolov8484

No significant difference in accuracy between 6.05 and 6.08. Maybe 6.08 is less affected by dirt and bb residues inside of the barrel.

What barrel would you recommend to buy pdi 6,05 300m or 6,08 300m

I use PDI 6.08 in both of my HPAs, so... :) And try it with R-hop patches from Snipetor or Faceless Sniper.

Definitely worth it. It's much easier to have a good consistency, accuracy and grouping with GBB buckings than with the AEG ones.

@@NikolayDimitrovFisher Also,I am planinng to do HPA DMR 2.8 J with 0.45 g. Is 6.15mm 500mm barrel an overkill?

@@user-ye7jt8wz9n probably yes.

@@NikolayDimitrovFisher Up to what bore should I pick my barrel?

@@NikolayDimitrovFisher Also have a question will it fit MWS window barrels?