Thank you brother! This video was dope loved the music. Very helpful

So Im in the process of replacing mine, I notice on the new set there is a hex shaft, when the two pieces are put together, the upper does not spin, they lock together as and spin as one piece. This might be correct, if it is what is the point of having a bearing on the shaft?

What the heck kind of a world are we living in when you take your equipment to a repair shop and they say, ehh, that things not worth fixing.... this country has gone to pot 😢 I took my engine to a local shop for a simple repair and he kept it for a month no call nothing, I told him to just keep it 😅

Very nice, helpful info.

nice! after cleaning the caked on grass and dirt every year I prepped all the rust like you did, then I painted it with graphite paint. nothing sticks to it now.

I'm having problem with my belt my pulleys are good the belt is brand new and it just pops off

Excellent video. Thanks. Subscribed.

A lifetime of knowledge, makes it look easy 😎

You make it seem so easy unhooking these wires is nearly impossible.

Hey man I'm in the process of doing this right now and need help is there anyway possible I can call you? If you have the time or if you can help me answer a couple questions on here I would appreciate it

Best video!

Someone shorted everything out it’s not the mowers fault it’s the operators like every other think wrong.

Great video!! What are the initial driving symtoms before the transmission pulley fails? I have over 200hrs on my JD130 lawn mower. I just replaced the main drive belt. I have noticed there is less and less power while going forward or in reverse. When I raise my foot off the gas pedal it seems to regain some power but not much it then gets slower and slower. Would the transmission pulley be a likely culprit?

Wish i had watched your video first. The harness pissed me off so bad i had to step away because i found myself daydreaming of cutting off all the wires to pull out the motherboad box.😂

Where are you guys ordering the motherboards from? I have the same power issue. Sounds like an LG recall that needed to happen but didn't.

All you had to do was bend that down or cut it. You need to do Governor mod with zip tie

Glad I found this video, got my board fixed and washing machine running, thanks for the video!

VERY WELL DONE, GOD BLESS

Great help, defined my problem exactly. The process steps and kit part number are very helpful. Thank you.

Bad idea! This engine as build, is designed to run at a maximum RPM of 3600. Running faster than that, can cause the ignition magnet to come off of the flywheel doing irreparable things to the engine! This happened in my case. The glued-on magnet came off of the flywheel and broke the coil and its cast mountings, loose from the engine! Now I am SCREWED!

Thank you, thank you, thank you. Our machine wouldn't turn on and I did what you said by unplugging the washer and holding each button down 5 seconds and plugging it back in. Praise God it worked. You saved the day!

This is awesome for D 105

bro called the washer a computer

Good stuff

You need to put a small spring on the screw to keep tension on it so it wont move once you set it.

I got questions for you i have the same truck

First off - great video! - just finished reinstall and am doing my first run. Next - dude you must have gorilla grip fingers! I ended up carefully using a pair of small channel locks. I found a slight wiggle, side to side as you pull sees to helps. Another thing that helped me get the controller to a "easier" working position was to squeeze and push in the blue plug from the back of the machine - it will let you pull the wires out of the way a bit. Again great job and thank you for postiing!

Fact is every 100/200 hours expect to replace it, that’s what I see happening in our shop Just cheap crap Green doesn’t mean Good anymore folks Buy from a dealer is smart 😊

Great short video thanks

I’m confused to as the how the washer and the screw attach to the top of the pulley?

Remove all the inside cover on brging and you’ll save time and money, plus down time during busy Season

excellent, just got a new LG washer 2yrs old, only needs that same board

How long did this repair last without it coming apart again?

Nice work bringing this unit back to life! I still can't figure out why the new cam fixed the starting issue. The old one didn't have any defects that I could see in the video.

ok you forgot to mention the most important thing. part number where is it located mine is almost the same but the numbers "3357" are different mine EBR32268007 IS THIS THE PART NUMBER OR WHERE

I just snipped the tab off so the screw goes over the tab. I was lazy haha I just had to take the air filter element off to get my snips in

Perfect. Thank you!

Does that board control the temperature as well?

Amazing work, my washing machine has the same problem, I have check everything and tried every trick but it looks like is the mother board which is very expensive

I tryed the zip tie trick and works great, just scratch up hands and arm a tad No big deal and hour and half done

That throttle stop and engine governor are there for a reason! 🤦

Could have just cut off the threads...

Truth is I think the repair shop was trying to steal his mower for nothing and fix it later Crooked people

Well done and it’s as good as new now

Good information 👍

Great video! Was easy to follow. I did these steps and got the gov removed but now when I’ve got throttle full out it backs itself off then re-engages. Any advice on what could be causing and how to fix?

Nice Job! I wished that I work as fast as up do :D

So i brought a new motherboard just came in yesterday plugged everything back up put a load I. And the same thing happened again midway thru it cut off and won't cut back on 😩 any idea as to what it maybe maybe??

I just had to buy a new engine for my ct200u i just installed it it tops out at 20 if I remove the Throddle screw will it cause any damage?