JD D105 Replacing the Secondary ( Variable Speed) Pulley using Zip Ties and other work PT.1 REVIEW

Рет қаралды 41,252

3 жыл бұрын

My friend gave me this really nice JD D105 with only 225 hrs. He hadn't used it in years because his General Transmission secondary pulley had gone out. Apparently it was not worth repairing but I am going to give it a go. Enjoy the video.

Пікірлер: 46

@ryancarraway3896 2 жыл бұрын

Ive seen probably 30 videos on this and this one was the only one that was helpful. Thank you

@fixinitproductions2464 2 жыл бұрын

Glad it helped!

@mitchellgalloway9345 2 ай бұрын

A lifetime of knowledge, makes it look easy 😎

@sladeoriginal 2 ай бұрын

nice! after cleaning the caked on grass and dirt every year I prepped all the rust like you did, then I painted it with graphite paint. nothing sticks to it now.

@Travelwindows999 9 ай бұрын

Great help, defined my problem exactly. The process steps and kit part number are very helpful. Thank you.

@nancymelendez85 3 жыл бұрын

Way to go! Great work 👏🏼

@Mrpaponte 2 жыл бұрын

what a great job congratulations 👏 👍 thanks for the video well explained video

@philliphall5198 Жыл бұрын

Well done and it’s as good as new now

@Sarah_Swede Ай бұрын

Very nice, helpful info.

@rodneybrown2422 Жыл бұрын

Perfect. Thank you!

@philliphall5198 Жыл бұрын

I tryed the zip tie trick and works great, just scratch up hands and arm a tad No big deal and hour and half done

@ruthbaum1958 2 жыл бұрын

Awesome job💪

@fixinitproductions2464 2 жыл бұрын

Thank you.

@leaulentille2764 2 ай бұрын

Excellent video. Thanks. Subscribed.

@ethan5.56 2 жыл бұрын

Great video. About to tackle this project as well

@fixinitproductions2464 2 жыл бұрын

Good luck!

@el_ingeniero_87 2 ай бұрын

Best video!

@nickgarcia4610 11 ай бұрын

Good stuff

@sammiemohammed476 2 жыл бұрын

Wow totally awesome I enjoyed that! As a girl I’m staying away from D105 though!

@fixinitproductions2464 2 жыл бұрын

Right on!

@tneville24 2 жыл бұрын

How did you remove the bottom part of the variable speed pulley?

@brucer1220 11 ай бұрын

This is awesome for D 105

@viralswim 13 күн бұрын

So Im in the process of replacing mine, I notice on the new set there is a hex shaft, when the two pieces are put together, the upper does not spin, they lock together as and spin as one piece. This might be correct, if it is what is the point of having a bearing on the shaft?

@jamessteele8000 Жыл бұрын

I’m confused to as the how the washer and the screw attach to the top of the pulley?

@jeffbornes3986 Жыл бұрын

Nice Job! I wished that I work as fast as up do :D

@philliphall5198 Жыл бұрын

Yea but I’m 72 and took 1 1/2 hours to complete it

@danm400 3 ай бұрын

@philliphall5198 glad to hear that! I am 65 and about to do mine today.😂

@davidlaws1438 23 күн бұрын

What the heck kind of a world are we living in when you take your equipment to a repair shop and they say, ehh, that things not worth fixing.... this country has gone to pot 😢 I took my engine to a local shop for a simple repair and he kept it for a month no call nothing, I told him to just keep it 😅

@philliphall5198 22 күн бұрын

Don’t buy any brand with the plastic trans period 😊😊😊😊 Most shops charge for 5/6 hours labor 😢

@philliphall5198 Жыл бұрын

Fact is every 100/200 hours expect to replace it, that’s what I see happening in our shop Just cheap crap Green doesn’t mean Good anymore folks Buy from a dealer is smart 😊

@Travelwindows999 9 ай бұрын

Mine failed at 163 hours.

@danm400 3 ай бұрын

Mine just blew the spring cap off at 201 hours. Found a kit with the pulley, spring, cap & screw on Amazon for $26.

@ScottOstr 2 жыл бұрын

Why won't my D105 go into high gear? I replaced the pulley but not the belt. Sadly, the existing pulley looked fine.

@bubbleslong9599 2 ай бұрын

I'm having problem with my belt my pulleys are good the belt is brand new and it just pops off

@philliphall5198 Жыл бұрын

Remove all the inside cover on brging and you’ll save time and money, plus down time during busy Season

@richardw4132 7 ай бұрын

Great video!! What are the initial driving symtoms before the transmission pulley fails? I have over 200hrs on my JD130 lawn mower. I just replaced the main drive belt. I have noticed there is less and less power while going forward or in reverse. When I raise my foot off the gas pedal it seems to regain some power but not much it then gets slower and slower. Would the transmission pulley be a likely culprit?

@danm400 3 ай бұрын

@richardw4132 mine just failed at 201 hrs. That little screw broke or fell out and the metal cap disappeared in my field. When you say "less power", do you mean less speed? The short belt around that pulley can wear out and cause less top speed. But try this: Take a blow gun and try to clean every bit of grass off the top of the trans. From all angles. It builds up under that pulley and in the linkage. When my top speed slows down, that always helps.

@stevendoe1555 2 ай бұрын

Hey man I'm in the process of doing this right now and need help is there anyway possible I can call you? If you have the time or if you can help me answer a couple questions on here I would appreciate it

@jorgecampos31 Жыл бұрын

How long did this repair last without it coming apart again?

@philliphall5198 Жыл бұрын

Average is 150 hours

@nancyvu1833 2 жыл бұрын

Can you show me how to take out the bottom pully.

@fixinitproductions2464 2 жыл бұрын

I would have loved too but I sold the mower. If it wasn't for that I would make a video for you.

@sandiespyrou2941 2 жыл бұрын

I had trouble taking out the bottom pulley too. After I pulled the release bar the back and placed the tractor in neutral, it came out right away.

@chrisflores5226 2 жыл бұрын

What is the belt size

@fixinitproductions2464 2 жыл бұрын

Hi there and thanks for watching. The OEM belt number is GX20072 or an alternative belt would be GY20570. They can be found at Lowes here is the link www.lowes.com/pd/John-Deere-42-in-Deck-Drive-Belt-for-Riding-Mower-Tractors/1000594523?cm_mmc=shp-_-c-_-prd-_-sol-_-google-_-lia-_-146-_-moweraccessories-_-1000594523-_-0&placeholder=null&ds_rl=1286981&gclid=Cj0KCQjwpf2IBhDkARIsAGVo0D3KAodfmA6fKGirMBDOIokqKQDrA1QAQOKQHNT91OXpm0b6aWwUv2QaAsk_EALw_wcB&gclsrc=aw.ds Also the specs on the correct size belt are 1/2" x 103.875".