Hi does the man truck use numbers on wire instead of color code
@RelectrikRepairs2 күн бұрын
@@johnmacharia4154 All MAN trucks have codes/numbers on wires.And they use 3 colours most..brown for the ground, white and pink.
@johnmacharia41542 күн бұрын
Hi am requesting if you know wire color code is good to mention so that i will learn am am following most of your videos.thanks
@RelectrikRepairs2 күн бұрын
@@johnmacharia4154 thank you very much!I will mention every wire colour or code.🙏
@johnmacharia41544 күн бұрын
Hi i would like to learn this job
@RelectrikRepairs3 күн бұрын
@@johnmacharia4154 Thank you for your comm.If you will keep watchin my videos,you will learn a lot!🙏
@kashiftalib55485 күн бұрын
New model 😁😁😁😁😁
@RelectrikRepairs4 күн бұрын
@@kashiftalib5548 yes..it's an euro 7🤣
@jeffogle98235 күн бұрын
I drive a dafcf85 510 with a 18 speed roadranger manual dont have any electrical problems!
@RelectrikRepairs5 күн бұрын
@@jeffogle9823 that's great!Wish you many miles without problems🙏
@hacking_tutorial7779 күн бұрын
80 503 lock 😊
@jawadpapay444713 күн бұрын
We need to learn your experience , not for listen to music , plz do not do the music . We can't listen to you
@RelectrikRepairs12 күн бұрын
@@jawadpapay4447 Thank you for your feedback.I will make some changes.You can also whatch this video (same topic) :kzfaq.info/get/bejne/addkacpirZPOgX0.htmlsi=mhj-oiIpsMpQKVX2
@kylehoughton257816 күн бұрын
Hello sir I have a problem with a Man tgs 33.360. I have no rear brake light. Just wanted to know where is the brake switch located
@RelectrikRepairs16 күн бұрын
@@kylehoughton2578 Hello.First check under the hood in the top right connector box, if you have power on wire 43 300 when brake pedal is pushed.Also check all the abs and zbr fuses.If not some of the MAN trucks brake light switch location is typically situated near the brake pedal.
@gurpreetsingh-bv1is19 күн бұрын
Hi I have man 2014 TGM Automatic.It Is showing some time gearbox ecu also creating bit noise from the place of clutch booster. When I restart or restart after some time. It’s disappearing. May I know. What will be the issue.
@RelectrikRepairs19 күн бұрын
Hello.First you will need a diagnose.The bit noise appears because clutch booster cannot engage, and the can be from the pressure plate,pressure bearing or clutch booster.So just to be sure you need to make a diagnose on the gearbox.
@gurpreetsingh-bv1is15 күн бұрын
@@RelectrikRepairs thank you so much
@FreddyMassawe21 күн бұрын
Ok boy
@FreddyMassawe21 күн бұрын
Ok boy
@alvesthegreat24 күн бұрын
Sir you are brilliant 👍
@RelectrikRepairs24 күн бұрын
@@alvesthegreat thank you🙏🙏🙏🙏
@GRZEGORZWODZUАй бұрын
👍
@JosephAgyei-ih7wjАй бұрын
Good
@hawaartochanel36Ай бұрын
What about when N is playing what to do pls
@RelectrikRepairsАй бұрын
That happens when the gearbox doesn't have sufficient air or the slave cylinder has a problem.
@RelectrikRepairsАй бұрын
Faults codes appear on the ins. Cluster?
@CHIEFNYANHANDAАй бұрын
Thanks
@kassimismail6127Ай бұрын
Thanks a lot
@mihaelatruta4738Ай бұрын
Thank you for sharing ❤❤
@megdaranisrl2339Ай бұрын
Where we can donate some money for sharing your work? ❤
@RelectrikRepairsАй бұрын
Thank you for watching.You can buy super thanks or in my channel bio you can find other ways.🙏
@mihaelatruta4738Ай бұрын
Thank you❤
@StepIn-tl7dpАй бұрын
Good work God bless you
@RelectrikRepairsАй бұрын
Thank you very much🙏🙏
@user-km9vu9mw5yАй бұрын
What type of device do you use for inspection? I want to buy a truck inspection device
@RelectrikRepairsАй бұрын
I use Launch x431 and autocom 2020 but i recommend Launch tester.You have way more options and its advanced.Also it works with some tractors and heavy duty machines.
@user-km9vu9mw5yАй бұрын
@@RelectrikRepairs Which category supports trucks from?
@RelectrikRepairsАй бұрын
@@user-km9vu9mw5y All trucks,man mercedes volvo daf iveco scania renault and many others
@user-km9vu9mw5yАй бұрын
@@RelectrikRepairs Which category is in Launch?
@RelectrikRepairsАй бұрын
@@user-km9vu9mw5y Launch x431 is a medium-superior tester for all trucks
@muguladaniel6362Ай бұрын
Am requesting to erase EBS codes in TGS using cheap auto com scanner.
@RelectrikRepairsАй бұрын
Yes,you can erase most of them
@user-mx6dn4rq5oАй бұрын
❤❤❤good
@azuzkharef2293Ай бұрын
Good
@PH-Truck-MechanicАй бұрын
good job!what tester are you using?
@RelectrikRepairsАй бұрын
Thank you very much.I'm using a Launch x431 and also autocom 2020
@PH-Truck-MechanicАй бұрын
@@RelectrikRepairs thank you!
@alvesthegreatАй бұрын
If this valve block is there.... Will it show on the dashboard.... I have 2008 MAN TGL 7.150.. D0834 engine ZF gearbox ... When I'm in first gear it shows 3rd on the dashboard... When I'm in 3rd gear it shows 6th gear on the dashboard....
@RelectrikRepairsАй бұрын
Ussualy when this is happening it s because an electrical fault.A bad sensor inside the as tronic module,if it s about automatic gearbox.If its manual gearbox the problem is from the valve block.
@alvesthegreatАй бұрын
@@RelectrikRepairs hello... Not seeing a valve block
@RelectrikRepairsАй бұрын
@@alvesthegreat The valve block is that one wich has a round plug.On the top of the gearbox.
@IbrahimMuhammedmusa-ct8gdАй бұрын
❤
@plummer537Ай бұрын
Can you please send me your phone number
@christianmusa3265Ай бұрын
Do one video of actros
@garycook67172 ай бұрын
Happend to me a couple of weeks ago. Lucky there was a VMU on site and mechanic broke into MAN truck for me
@muguladaniel63622 ай бұрын
My software brought no short cut.what can I do.
@RelectrikRepairs2 ай бұрын
Tell me more,what do you need to do?
@riccardoo.56802 ай бұрын
Bravo
@jalelsaidi38272 ай бұрын
Plz im looking for the wiring diagram for DAF CF85-410
@RelectrikRepairs2 ай бұрын
In the edc connector you need to have power on the red wires,with the ignition on and 60 ohms on the twisted wires (plug connected) .120ohms disconnected
@jalelsaidi38272 ай бұрын
@@RelectrikRepairs all is okay But no signal but stilll no output signal to starter But when relay G426 disconnected the engine will be cranks but not started
@RelectrikRepairs2 ай бұрын
@@jalelsaidi3827 That means the edc is not fully powered on all wires..if it cranks and not starting
@RelectrikRepairs2 ай бұрын
I think you schould have 2 permanent + wires and 2 + from the ignition
@jalelsaidi38272 ай бұрын
Engine not cranked definitly What do u think plz
@RelectrikRepairs2 ай бұрын
Usually when cranking is short and not long enough to start, it can be a problem from the starter(the big solenoid).But do you have active faults? Engine warning?
@jalelsaidi38272 ай бұрын
@@RelectrikRepairs when we supplied it directly its was worked normally but the engine not started But by the key switch no reaction definitely The display its dark Can't see the error message But sometimes i have see the check engine appears Its show also EBS SYSTEM Problem What do u think plz
@zedohh44502 ай бұрын
Hello. Great Video. My truck will not get in gear but there is no fault display. If I turn the switch to D, the screen still says N, when I turn the switch to Dm, it shows N and M . Same thing happens when I put in R, screen only shows N and when I put in Rm, It Show N and m. No change to D or R and there is no error code or alarm. Do you know why?
@RelectrikRepairs2 ай бұрын
Thank you! If you don't have any fault code active it can be only one possibility.Every time i encounter this problem it was from the rnd switch.The switch from where you select gears.And a diagnose will help.to see in real time what happends when you select D or R.Good luck!
@muguladaniel63622 ай бұрын
Bro am requesting your WhatsApp number.
@mihaelatruta47382 ай бұрын
Multumim pt ajutor❤
@mihaelatruta47382 ай бұрын
Thank you for sharing ❤
@mihaelatruta47382 ай бұрын
Thank you for sharing❤
@mihaelatruta47382 ай бұрын
Thank you for sharing❤
@mihaelatruta47382 ай бұрын
Thank you for sharing❤
@mihaelatruta47382 ай бұрын
Thank you for sharing❤
@kinghlatshwayo97032 ай бұрын
Þhi mate i am.not sure if you can assist i have a man tgs 27 440 2012 model it takes all gears retard works but when u stop completely it goes to neutral N then u need to reselect D for it to move not sure what it could be
@RelectrikRepairs2 ай бұрын
Hi.If you don't have any tcu or ffr fault on the screen ,you will need an diagnose to check everything on the gearbox and see exactly whats happening .Good luck🙏
@noku77752 ай бұрын
Renault truck x2 pistons are filled with water, how do I fix that without buying new ones?
@RelectrikRepairs2 ай бұрын
Hello.If you have water there it means that you will need to replace the cylinder head gasket and also check the the cylinder head for cracks.Maybe you can resolve it only with a new gasket.