Ey doble d l. Never Ever see it the way how did you put the pats
@abdulq12847 ай бұрын
He eventually replaces the belt with new one ..no repair...dont bother watching his other two videos...waste of time
@abdulq12847 ай бұрын
You have three video for repairing ..yet you replaced the belt and NO repair ..what a waste of time.
@furaqfever9365 Жыл бұрын
Thx for the great video really inspired
@sourobsonmarcel Жыл бұрын
Hello, all right, please send me your address for Suave Caragem, I want to see what's going on with my Prius 2007 car.
@jeffoh5787 Жыл бұрын
Toyota told me my compressor went out on my 2008 and shot metal shavings all through the system and everything needs replaced for like $4,000. I am a pretty good diy guy, any recommendation as to what I should do? What can I inspect to see if they're telling the truth or not? Thanks for the great videos btw!
@doubledsgarage-ddg3103 Жыл бұрын
@@jeffoh5787 turn it on first and see what sound it makes first before pulling it.
@jeffoh5787 Жыл бұрын
@@doubledsgarage-ddg3103 Sure thing, I'll record a video and post it up. Thank you so much for the help!!
@doubledsgarage-ddg3103 Жыл бұрын
@Jeff Oh I don't hear any grinding.... if you remove and dump it out if there are fragment or not. If no fragment then possibilities evaporator valve which is a pain to replace. If you do a vacuumed and fill u some AC and if it works the. You should be good. Remember to not use off the shelf freon. Use r134 I believe which is pure. Don't use the one with peg oil, you will destroy your system if you do.
@doubledsgarage-ddg3103 Жыл бұрын
@Jeff Oh they usually say that until they open the line to check. Most of the time they are too lazy to check. Only way to know is to get everything else. Had the same happen to me, car was too old so decided to do it myself. Change the compressor, vaccume and all was good.
@doubledsgarage-ddg3103 Жыл бұрын
@@jeffoh5787 do the foam clean... then replace the compressor. I managed to get a used compressor for $100. Then vacuum then refill. If it doesn't work... then possible evaporator valve. Happy yo help over a phone call.
@xZen0sx Жыл бұрын
Thanks!! Btw, which side skirt do you have it on your CS?
@doubledsgarage-ddg3103 Жыл бұрын
Here you go. Had to do some custom cutting but it came out nice. It's dial layer and thick, not like the cheap one out there. Fits for 2015-2020 BMW F82 F83 M4... www.amazon.com/dp/B07GXZ6FYB?ref=ppx_pop_mob_ap_share
@BPF80MCar-vi1pg Жыл бұрын
I ordered one of these for my m performance lip. Should be in a few days
@csi7312 Жыл бұрын
Looks horrible 😅🙈
@solomanosiris2395 Жыл бұрын
🔥 Promo'SM.
@unjustkatana Жыл бұрын
The video starts at 1:40
@serok1358 Жыл бұрын
❤
@csi7312 Жыл бұрын
Looks cheap in my opinion. Such a great car with lots of carbon from factory and then putting a cheap plastic piece on it...🙈
@csi7312 Жыл бұрын
Great car ❤️ And it comes with Carbon ceramics 😉👍🏼
@marcolias Жыл бұрын
Double D back in town!
@marcolias Жыл бұрын
Sweet ride, nice mod!
@lancealot9644 Жыл бұрын
Thanks my friend. My F80 is next rj11
@mathw2703 Жыл бұрын
i wonder why you can push down the CAT at 10:53, when its properly bolted to exhaust manifold ...?
@nicknelson94502 жыл бұрын
Thanks for the video. FYI, when I was putting the carpet back in place, I realised that you can actually reach the outlet tube just by reaching over the left-hand corner when the carpet is in place...might be a bit more tricky to catch the liquid coming out but not impossible.
@jdogg96962 жыл бұрын
Curious why you didn't choose to install the factory tow kit with a cooler and 7 pin factory setup.
@csboi2 жыл бұрын
Who did you contract for the transport pls? I'm transporting the exact same car lol.
@doubledsgarage-ddg31032 жыл бұрын
Let me check tomorrow and get back to you.
@romeolongoria87302 жыл бұрын
Wifes ‘21 prius smells like theres a pizza 🍕 and soggy cardboard in the dash. Is it possible I already need to do this?
@gmcc72 жыл бұрын
Next time drop the dumbass intro
@tkisok48832 жыл бұрын
Can you provide us the part numbers for the hitch, the wire harness, etc?
@markkuzmenko56532 жыл бұрын
Thankyou
@erikisbaum2 жыл бұрын
all that other shit was unnecessary in the beginning. gooooood lord
@juarysilva5592 жыл бұрын
Why is the intro so long my dude
@Devo19872 жыл бұрын
Put a new spring in find one close looking to it junk yard maybe a different car your never know :-)
@brianw66452 жыл бұрын
Good video and very thorough explanation. Thanks for posting.
@Baztation2 жыл бұрын
dream car
@limosine2 жыл бұрын
You can just access the hose from under the car to save ripping your carpets up.
@doubledsgarage-ddg31032 жыл бұрын
Very true, but I have a cat shield so it's covering the line.
@xxxbigmojoxxx2 жыл бұрын
👍
@giorgioye2 жыл бұрын
cool! do you think an endos checking could be useful to clean prius evaporator? in your video the job was done totally blindly
@rodrigovazquez18742 жыл бұрын
Did it work?
@doubledsgarage-ddg31032 жыл бұрын
Yes.
@manp10392 жыл бұрын
you might like to know it was reported on December 14, 2021, San Jose police arrested 15 people and recovered over 1000 Prius catalytic converters that were stolen by them. And the San Jose Police are figuring out how to get the catalytic converters back to the persons they were stolen from.. you might be able to get your back.. and perhaps you could sell it to get the money back you paid for the replacement?
@manp10392 жыл бұрын
you might like to know that it was reported on December 14, 2021, the San Jose police arrested 15 people and recovered over 1000 Prius catalytic converters that were stolen by them. And the San Jose Police are figuring out how to get the catalytic converters back to the persons they were stolen from.. you might be able to get your back.. and perhaps you could sell it to get the money back you paid for the replacement?
@mrvic921542 жыл бұрын
When I placed my shield I put rivets between the three bolts into the frame where the plastic part sets and then I put the plastic part on to cover them up to surprise the thief not knowing that it's riveted underneath as well, I also used different size rivets and instead of breaking away the stems I would leave them in there and just bend them over that way they can't just drill them through because the stem is in the way of the rivet, I even placed dummy rivets all around that went to nothing just to make it look more difficult, I never thought of putting another shield up inside the engine compartment or in the back something to look forward to do later, thanks for the video
@jovannihernandez622 жыл бұрын
What did you do to prevent the rattling?
@doubledsgarage-ddg31032 жыл бұрын
Remember to slightly bend it before installing
@jovannihernandez622 жыл бұрын
@@doubledsgarage-ddg3103 slightly bend where? The center shield? Is that where it’s hitting?
@doubledsgarage-ddg31032 жыл бұрын
@@jovannihernandez62 yes. The center shield. Toward the back is where you want to bend it. It's where the catalytic converter comes into contact.
@dfrees422 жыл бұрын
If fashion grey and urban green had a child 🏆
@mrvic921542 жыл бұрын
Sorry to see that you lost your cat to a worthless greedy no good SOB thief, I also have a 2007 Toyota Prius and I have installed a cat shield but about 6 months after my check engine light came on saying that my cat was not working properly so I changed both of the O2 sensors but still got a check engine light so I shopped around and called several different Toyota dealers in my area in San Diego county and to my amazement I found a brand new complete from bolts to end of pipe Toyota catalytic converter with muffler for about $1,800 brand new (no welding necessary), to use an old used catalytic converter is taking a big chance because you really don't know the life why not pay an extra $100 and get a new one, I was lucky that they did not ask for the core because I was able to sell my old no good Toyota catalytic converter for $1,900 legal, I guess the old catalytic converters have more precious metals than the new ones yet the new ones work just fine because I just did my smog and it passed without a problem here in California, best of luck thank you for the video
@carsandcoldbrew64892 жыл бұрын
Are you from the Bay Area? Will you be able to help me install my CS rep front lip and splitter?
@@carsandcoldbrew6489 just replied to your email. Hope that helps.
@TheMadTitanM52 жыл бұрын
Kinda disappointed that the M5 wasn’t represented well here. I think I only saw 2 other f10s (along with mine) and 1 e60. Great turnout nonetheless, and great video!
@doubledsgarage-ddg31032 жыл бұрын
Agree. We didn't see many M5 either. Sorry if we missed yours. 😔
@TheMadTitanM52 жыл бұрын
No worries, you got my car at 2:16 in the video.
@shaneswiss2 жыл бұрын
Nice
@sund85953 жыл бұрын
wow very nice car and colour
@earthquake1613 жыл бұрын
i cant even drive yet im watching this! very helpful if i did own a Acura
@jaimehurtado3563 жыл бұрын
Looks good man, how long did it take to get the lip?
@ROYKN6WBK3 жыл бұрын
Thanks for the video. How did you transfer the hole pattern from the level 2 rear angle CAT bracket onto the main shield? The bracket sits on top of the shield and the holes are blind.
@doubledsgarage-ddg31033 жыл бұрын
The bracket comes with pre drilled holes. Just do a dry fitment and mark it with sharpie before you drill the hole and rivet it together.
@morodriguez21253 жыл бұрын
They had stolen a lot of Prius cathartic converters.. well have to call congress to have them look around by.. cus I believe is an organization.