Can you send link for that piece you replaced

I have had my 60" z force for 15 years and I changed the trans fluid every year no problems .I put three spring on it .great mower

I can’t remember were a spring and washer goes ,,,,Need Help

I followed this procedure perfectly and it worked well for a couple of months and then the problem of slipping was back again. Hydra gear makes junk.

Great video! About to my left side! P.o.s! Struggled all last summer trying to mow with 1 transmission working all the time. Other one worked until it warmed up and would get weak! Thanks again for a great video!

So mine is of course is the left hydro and as I mow the unit gets hot and is not very responsive. But cold at first it turns fine. What if you just changed the oil from a multi V to a straight 30 or 40 weight or even a 50 weight? Isn't the problem the oil thins as it gets hot? Yes I'm lazy and afraid I'll screw it up!!!😉

I'm going to do mine shortly so THANKS for the video!!!! Also these hyro's seem to be on so many different Brands that it "might" be a great way to start a biz offering to rebuild these. If proficient at it how much time would you say it takes to rebuild? THANKS!!!!! Most people would not attempt doing a rebuild.

put bypass in with wheel bearing grease it will be sticky and hold it in place

at the end of the Video you adjusted the neutral position. Was the engine running to check if the wheel would spin forward or backwards ? ( to get Neutral at the correct spot )

Your carburetor idle circuit needs to be cleaned.

I don't usually comment but we'll done video had to give you 30.sec of my time to like

the only thing I feel you left out was price for sealer kit , parts and shipping,

Good idea just getting the center section those complete kits are pricey.

Losing power from right hydro, why do grooves hurt the center piece? I checked my check valves, they are tight, I do have metal shaving in the filter. Thanks

your video is helpful but you leave out important steps, (washer placement). This is like watch repair; generalization is not good enough, it must be step by step specific if you're trying to teach someone how to do it. 🙃

wanting to find out how old my transmission is Info on the sticker: HYDRO GEAR top right 618-04327 bottom left 6060B50239 MOWER IS TROY-BUILT RTZ50 Ive had it for many years. About 300 hours. Cleaned and greased after every use. Garage kept.

This failure/repair is all over the Internet and causes me to believe this is a design failure because it is certain to happen on the left hand transmission to every zero turn mower owner. I love the tractor when it’s working, but I will not buy another.

I expect this mower will last several seasons with decent care. kzfaq.infoUgkx1VWTrayKBdCKAjzAcZ_Eg4dhHTae3LkN also recommend Also, I ran across the problem with it not starting the 2nd time I used it. There is a safety switch which is pushed in by the chute or mulching piece being attached to the deck. I took the cover off and it wouldn't start. Put it back on, no problem. It takes only a minute with 2 easily accessible wingnuts and no tools. This mower starts up first crank each time and it is a joy to use. It also mows in reverse by putting the key to the reverse area after starting and pushing in the triangular button. It will stay in reverse mode until you turn it off. All in all, for my homeowner needs, I really like this mower-and at 70 bucks a cut here in Miami, it's already more than 1/3 paid for itself in a month.

I know yard tools use the crappiest oil they can buy for manufacture. Could these transmission problems be avoided by using synthetic oil? My JD LX176 1994 still runs great after 30 years of mowing and snow removal.

get it bubba. glad to see you're making content again

Good video but you never showed it start after your rebuild? Any reason why?

Just got done replacing both left and right side center sections on my Husqvarna RZ5426. My finger was too big to hold the bypass valve in place when installing the center section so I just used a zip tie to keep it in place. Worked like a charm.

Maybe a good way to prime the unit would be to drive it with an electric drill while the unit is still out of the mower. That way after priming is done, you can easily check the oil level and fill as needed without having to remove the unit from the mower again.

I have a broken cradle bearing and the manual is saying its only available with a new case, but I found the cradle bearings sold separately. Have you ever replaced those? Not sure if they just rest there in the case or if they are adhered in some kind of way.

All 6 volt cubs were positive ground from factory fyi . If you switch it back to positive ground you will have to repolorize generator. Thanks so much for the video of your great little Cub !!!

Where is the TO35 running video?

I just bought this very tractor. Lol was there a reason you got rid of it? Any issue when you sold it with?

How many hours do them pumps last until problems start happening ??

Hey DarbleyTheTractorGuy is this the 17AI2ACK056?

Hey, Darbley. Everything works fine, the mower runs like a dream, but one issue, the bypass rod does nothing. I put it in, the same way it came out, and absolutely nothing. I can't find the reason, hopefully you can point me in the right direction, thank you!

Is there any reason why you couldn't do the purge procedure using a drill before installing it? Seems like it would be easier to add oil if needed while it's still on the bench.

I have a gas 202 Massey Ferguson w/102 loader. Is there a seal between the pump and engine where my hydraulic leak is?

Have not had any luck with mine I tried this and it worked great for about 45 minutes then it started losing power again back to where I started I went ahead and ordered the whole transaxel

I had a home depot cub cadet. Very deep in the manual it stated that the life expectancy Was 185 hours. I sold it soon after. Box stores dumb down the standard product to make more money. Never buy major equipment from a big box store.

Excellent presentation..!!! I’m having trouble getting my center section out.. you skipped past that part. Everything is disconnected but it seems like it’s jammed in there.. worried if I just try to pry it out that cheap metal will break and parts will go flying everywhere..

Just FUI if you use RTV you want to set the pan cover on just after applying the RTV. But! Do not put the bolts on for about 30 mins that's let's the RTV set up and make a gasket! Should be about a 1/8 gap while setting up..Then torg down.

How about a cell so we could text ,thanks

Excellent video! Got a new subscriber here

it's wonderful video, and good instruction, the Piston pump was amazing, do you know which one is the leading company for this Piston pump?

What all did you have to buy, just the center section and seals? Thanks for the video.

What do you think - Should I send this part back- Hydro-Gear 71530 Kit Center --> kzfaq.info/get/bejne/b9qFmqhy2OC6fpc.html

I recently purchased a Cub Cadet Ultima 54 inch deck with a 24 horse Kohler. I think it has this transmission. I don't have time or want to do any work on the transmission. I mow about a hour and a half a week with this mower. I am not hard on it and never will be. Currently it has 2.8 hours on it. How long do you think this will last and are these transmissions junk? If so I may get a extended warranty. Thanks for the video.

Excellent presentation. Clear, informative, detailed notes, mostly best practices, etc. Thank you for doing this.

I see you use the leftover plastic tubs from the lunch meat for parts as well.....

Question you said to re check level after doing the purge how do you do this ?

How can you tell if the pulley is bad? I don’t feel like tearing the whole thing apart? I might pull off & drain oil & refill

I have the same problem 🤪🤪🤪. Anyone near upstate New York the work on cube cadet and do this job?

Good video, One complaint--- slow down, and don't skip anything, we're trying to learn .

FYI.....the small bypass puck can be retained in place by the use of a small dab of grease.....means you dont need to keep your fingers in an awkward place......been working on these for over 20 years

I myself is starting to dig into a Davis Ferguson loader model 101 found in your video very informational