Great video now I can skip the dealership

What a great video for a great couple

No life story. No waffle on about how your morning was. Just straight to instructions. Very good.

The hardest part of this is removing the vent bolt and getting it back in.

i like it

The Saints have left the chat

It would have been nice if you had used a light taking vent plug out

The answer (unless you live in California) to solve this once and forever is the bypass kit sold by Hewitt-Tech. I installed mine and solved my problem. Those valves are a pain in the neck if you live up north.

last thing you said (is literally why i came here to watch this video) ... "again, uh, make sure you uh, check the fluid in the reservoir and make sure you have the "correct amount in there"""" :// what is the "correct amount!!!???

Great video

Finally someone who gets to the point does the job shows it clearly and doesn't want to act like a puss about it. Someone who isn't concerned about every little freaking detail and worried about being critiqued by the world. Thanks brother

I sprayed wd-40 into the hoses before the secondary air valves while someone started the engine. The problem went away.

Very nice job on showing the process! Thank you for sharing.

My car stuck in 4th gear and when I accelerate no powe the car barley moves and I changed the fuel filter fuel pump and no change if I disconnect the battery the car gets back to normal no problem

Man Your one of the best tech teacher I’ve seen. Thank you

Good tutorial 👍

Is this why my truck is completely stuck in 4LO? Please help!! It was put into 4Lo and now it won’t go back into 2WD at all.

Thanks for taking the time to film the video. When i do this I’m going to cut those harness clips and replace them from the dealer.

That was great. Can't thank enough

If I ever meet two of the engineers who did this truck, one is getting a hug, and the other is getting the hardest kick in the balls ever delivered by man. Love my '07, HATE working on it. The packaging is almost comically bad where things are located. Like today I ended up doing spark plugs. Any other vehicle with exception to the wife's car where the whole upper intake manifold had to come off never takes me more than an hour. '07 Tundra? Three hours! There's literally something in the way of Every Single Cylinder that has to be removed to get the coils out, and to get the plugs, you have to drop the socket in first, then chase it with the extension, then hope you can reach the b@stard without having to splay over the engine. And I'd call that easy compared to the alternator. Ugh... At any rate, here's to hoping it buys me a bit more time before the next backache.

My dealer told me about the recall 5k miles over the limit. Such horseshit

what size filter wrench is that?

I have 130 hours changed the oil but not the gear oil and my reservoir is empty what do I put in that matches the factory hydraulic oil?

Great video, question though. It always I have a minor leak from one side. It appears to be leaking from a circular piece towards bottom of transmission. In your video, looking from the left side, just to the right of the filter is a brownish circle, can anyone identify this?

it is recommended to use synthetic oil ?

Thank you for your great video you saved me money

Kod 2438👍

great vid. Thanks

P

Did you have loss of power? Like climbing hills or going over 30mph?

Good video 👍 .. did u reuse the gaskets on the manifold?

Very helpful! Thanks!

Bingle swhingle avocado dingle

The boogity snoogity

Great video! And I love the position of your jack stands. Is there any need to be level for this hydro change ? Some of the posters asked about jacking. This guy has a nice clip of his opinion on jacking and stabilization. kzfaq.info/get/bejne/Y5pknreVrt-cgIE.html

Thank you for the harness clip tip, i got stuck on that. Thank you again. Subbed 👍🏻

Great info this is the exact problem my 2007 tundra has. Do you recommend I have the dealership to do the labor of installing it

“Oil filder” haha

FILTER WITH A T

Do you put the plugs back in before or after you bleed the air from the system?

A recent URL would be nice, as the one in the video doesn't exist anymore.

1/4 allen key plugs SUCK!!!!! replace with the 9/16 external hex head plugs that take an 11/16 wrench it will put a smile on your face.........What a difference. Amazon Hydro-Gear 54730 Plug Genuine Original Equipment Manufacturer (OEM) Part

Is it 4.1 quarts per side or is that the amount needed for both??

Great video man, made the change smooth and easy. Once complete, it was whining as I rode it around, does that whining eventually stop?

Thanks for the video!

your wife is hot

The secondary air system was put on to appease the EPA. The truck doesn't not need it! Bypass kit on ebay, basically bolt on. Running for years, no problem at all.

Thank you very helpful... I will be doing this this weekend.

Great video. Where did you jack the mower up?

06 Sequoia with 116k miles and mine went out. Got the Hewitt Tech bypass and no problems so far.