What are the two smaller plastic connectors for in the picture? There are two big ones with the sides that you press, but I've no idea about the two other pieces.

How to fix replace, repair the switch ?As live in Australia.Just out of warranty built in 2021

Will it read a bridge diode rectifier? 4 pin

The level of magnetism of stainless steel can vary quite a bit depending on the grade. Some stainless steels are weakly or not magnetic at all. Others may have a magnet stick to them surprisingly strongly, just a little weaker than plain low-carbon steel. Many rulers are made of 430 stainless steel which is ferritic and as such quite magnetic.

Great videos u are making man thanks a hole heap

Is this shit work on plastic chopping board?

hello this still working?

Brilliant! What about any fumes?

Would this work on childrens garden toys etc... I have a large scruffy little tikes play frame .. Great video

I'm getting ready to order a 3 axis DRO for my mini mill, but was concerned with measurements and fitment. Your video provided excellent close-up visuals that provided all the answers to my questions regarding custom fitting if necessary. I too am a perfectionist. Thanks again 😊

I just done cleaning up three green chairs. They were dusting and could not remove the white dust with a wet scotch pad. I used an electric heat gun it worked well but a torch may be quicker??

Good review. Good to see a mains adaptor included and fitted with a DC barrel jack, rather than the garbage that is USB-C (in my opinion).

great review, thanks!

Very nice work. Interesting.

Thank you

If you make heavy use as I have I carry a needle with me as yhou can push that into the end of the nozzle when it gets blocked. I mostly clean on the very highest setting in the swirl motion. I have been having problems with using solution though so that has never really worked well for me but that may be my fault.I do need to use as have massive areas at home about 50 litres of hypo treatment on one very large paved area alone and cannot think of a way for the K7 to take all that in and spread it so will keep looking. I would like something to link the K7 to my open big mixed 50% water/ hypo and suck it through to the machine but I think that is perhaps not possible.

I got 4 stainless steel mudflap brackets off Ebay £37and just bolt the flaps onto them fit lovely.. no rust...

The worst thing about those mudflaps is the rubber splitting - especially if they get a bit heavy with mud or snow sticking to them as they swing about. Plusgas is great - it stinks if you get it on your fingers, though. Great vid - thanks 👍

Roberta wants one, apparently to let me know breakfast is ready 😳

How do you fill it, just scoop it in, I have a tub of the grease as opposed to a canister

E Z lok is also available in stainless.

can we still buy these

Leave the nut on but loose when pulling the steering wheel off, your dentist will thank you

thanks for the details mike! im excited for my FR24 build.. this gives me idea on how to mount.. great video mike!! keep it up!!

Ahh. That's pretty conclusive.

Excellent video!

Very nice work

Thank for this video, i have the same probleme

GOOD

What size is the arbor for the blade hole?

Nice your videos are a great help Mike.Thanks.

Thnx

My 1999 TD5 has no horn nor headlamp flasher and indicators dead wobbly. Currently in my local garage (defender specialist) for review/replacement - hope it's this and not another electrical thing. Should have done have done it myself I suppose but couldn't be bothered!

I've gone through three of these motors in 12 years - usually the spindle rusts up and won't move. The engine parts are fine. Current one is still working.

Thanks Mike, tweezers also make an alternative tool to access and remove/fit the speedo bulb/s.

So cool!

Did it on my faded black plastic guttering 👍

Isn’t that rubbish and a dreadful design. Love what you’ve done. I’d mess that up 😂

Ahh, you are giving me PTSD. I did mine at the end of last year after a dripping regular caused an MOT failure. It wasn't too bad, but when I ordered the new regulator block, I forgot to order the little O ring that sits behind the regulator and the block, so the bloody thing still leaked. I couldn't smell the diesel so it just looked like it was a small oil leak, but in fact, the diesel was picking up the muck on the back of the engine and by the time it was hitting the floor was black.

Excellent info. Thankyou

thanks for the video, working on a 201 now, same problem. It actually ended up in the bin but I saved it.

Hey Mike, I have this vacuum, and it's suddenly just lost suction, do you have any suggestions on what it might be?

Why aren’t you reorienting the bed knives of the press brake to bend the handle first? That’s the whole point of a break with fingers.

To anyone watching this in the future of his past, that length stop doesn't interfere with the vice as it's not supposed to go all the way through the casting. You grub screw it one side or the other and unscrew the actual stop & slide that to set the length.

If you use the ball bearings at two ends it will slide better because you have to press more for markings, but will soft pencil like 8B or 7B the markings is going to be more clear

The only mug that works with these mug warmers is th tin cups used of camping.

Excellent job, thank you very much!

Oh so this is what James Bond does on his sparetime

I just followed these instructions today. I took 10 minutes and worked first time. Tip: make sure you take the top off in a place that you can find the spring if it flys off 😊

Now that chair is motivating