You would have to either cloud host the camera through any app that can detect and host IP cams or you could use an RTSP style setup and open a port on your router to view it from any location. It's a lot more involved, but it is possible to do.

Glad to hear it was helpful for you!

This particular compensator will not work with a threaded barrel, however there are compensators available for threaded barrels. If you want to use a suppressor in the future you will need a threaded barrel. Fortunately the barrels on 1911's are pretty easy to remove and install, so depending on your choices, it might be best to have two barrels.

@@FoulNews thank you for confirming that. You mentioned the satin vs stainless steel finish. Is the finish on the gun itself (trigger, barrel) stainless or satin to match the compensator? I haven't received mine in the mail yet to know.

Can you ping the IP or hostname that you assigned to the Pi?

@@FoulNews no it won’t let me either

You can install Klipper for under $40 these days. A dangerous hack? It's literally just changing firmware to a much more capable firmware and interface. If you really need a screen, you can use Klipper Screen or convert the stock screen to work with Klipper.

⁠ I say a dangerous hack because if you mess up the firmware you break your motherboard. I did that upgrading a reality Ender three V2 neo motherboard because the instructions from Corey reality are incorrect and tell you to use multiple files when updating the screen. They also tell you to flash the motherboard and then the screen, and then they reference a KZfaq video that tells you to flash the screen and then the motherboard, you get that wrong and your motherboard is dead and you have to buy a new one. As far as flashing firmware, they give you multiple files and I discovered in reality you only use one file not more to successfully do it. So it cost me a motherboard. And yes, losing the functionality of your screen is ridiculous. How else are you going to control your Z offset, nozzle temperature, increase your decrease the speed, start stop or pause the print? If you don’t have a screen, that’s ridiculous. So yeah that’s completely outdated hack and using the sonic pad at least gives you a screen. I’m sure you have an answer for how to print but if you can’t control it with the screen, you can’t pause you can’t you can’t stop other than just shutting the power off to the machine if it has a failed print. You’re literally downgrading your machine for clipper in this case

@@AlexDiamonds there's a comprehensive web interface that you can access from any computer or phone on your network. That's how you adjust things and monitor prints without a screen. Klipper is far more advanced than Marlin and doing the conversion incorrectly doesn't brick your mainboard. Again, you can use a Klipper screen compatible screen or convert the factory screen if you really need one.

I'm not sure. It would be best to verify with Valkyrie Dynamics.

Yes, you'll need to leave ignition on. You should use a minimum of a 6A battery charger while it bleeds if you aren't sure if your battery is healthy enough to perform the procedure.

@@FoulNews thank you. How do i know it's complete ?

@@sniperwolf786 No prob! It'll shut off by itself after 10 - 15 mins. It typically takes 12 mins, if I recall correctly.

@@FoulNews cheers appreciate this. Thanks again ♥️

@@sniperwolf786 No prob! Good luck with the repair!

You may need to do the makefile command again or double check the directory that Klipper.bin should be in.

I got the window switch on Amazon. The link to this part is in the video description.

Thanks, glad you enjoyed it!

lol, thank you. One of these days I'll have to finally act as the spokesperson for my company on here haha.

Nice, I bet they're a lot better now at night! Glad to hear that you found the video useful.

Yes, but you'll need to make sure to use the correct printer.cfg file for the S1, as well as making sure that you create the correct Klipper.bin file for the S1's mainboard.

I haven't done that yet, but it's a good idea!

Glad to hear you found it useful!

That is correct. You would either need to do some more configurations or use compatible Klipper Screen hardware. If you want to use the factory screen, follow this guide: www.reddit.com/r/ender3v2/s/uVGJNFKlDz

The one I have works pretty good, but you just have to go very slow and do 2 - 3 passes in the same spot for it to clean effectively. I filmed some of it already, but haven't had the time yet to finish it. Hoping to have it done in 2 weeks.

It's all special effects, took about 20 hours, but I edited the gloves out 😂

Thanks!

They're there just to distract you from what's in the background.

@@FoulNews LOL 🤣🤣

I recently just did my driveway with a Westinghouse 15" surface cleaner. It works pretty well, but you'll have to go slow and make 2 or 3 passes with it. The biggest issue is being limited by the pressure that this pressure washer can produce, so no matter what surface cleaner you use, you'll just have to take it pretty slow. I've got a follow-up video I filmed coming out in about 2 weeks using the surface cleaner. This is the one I've got now: amzn.to/3JqLJIJ