bracelet is sick!!!

May I ask what the tool is you’re using for your silversolder wire? Been looking everywhere for it haha!

spring for a Durston powered mill.... I have two of them and have never looked back.....

Cheap Mill....you should have 2 sets of gears....that way they engage more smoothly and consistantly....and the father apart you have your rolls, the less engagement you have of the gear set...

That's not a complete 100% Ramses!... looking close it's looking good but .. need some more in don't say it in English...pero en castellano, esta hermoso, mis primeros salieron asi..pero buscando mas encontré rl detalle , las cadenas en espejo las debes soldar en diagonal y sin cortar los sobrantes, después sueldas el sobrantes entre si,les das forma con un pequeño yunque redondo y después lo pliegas , rebajas con lima y pules. Asi queda la media luna perfecta de las caras.

Too much background noise

Бро! Припой проволоку делай потоньше чтобы легче было паять

Maybe you've figured it out since you made this, but to keep it in alignment while soldering, there's something welders use called "tack welds" to hold several pieces together to make sure it's all squared properly before making all the welds. If you just solder in the middle and at the ends, then your entire piece should remain in alignment. You could call it "tack soldering" I suppose.

Read the manual before you touch it. It's not a toy!

When the rollers are far appart take a piece of foam or fabric and wrap it around one gear, experiment with thickness and material to make it work, it will take up some slack in the gears and it actually makes other so you can get the rollers even further appart than stock ❤

Glad to see you back 🎉🎉🎉, you have some of the best tutorials on KZfaq especially the Ramses bracelet

What’s the liquid at 11:00

Hi silent Bob! First of all: DOGMA was great! But regarding the microscope: Do you have an Amazon Link for the light?

Братан, концевые и замок карабин не подходят для изделия такого рода. Одно дело когда ты одеваешь цепочку на шею и у тебя обе руки свободны для этого и совсем другое дело когда ты будешь в извращённой позе пытаться застегнуть такой браслет 😊. Сделай хотя бы часовую застёжку и концевики с шарнирами. А если время будет позволять, то замок-коробка на таких браслетах идеально смотрится. Это занимает больше времени и выходит дороже, но клиенты будут довольны!

Thanks for the video and info on the mill. Please wear a microphone. Would make it that much better. Cheers

3:26 *Brah, '4 mounting holes' refers to the base plate, which has 4 holes.*

thanks for the video, i enjoyed your explanation easy to follow ..But the music is totally overbearing, please sort the music to be softer. thanks

Cody is it possible to melt the ends with a hand torch

how do you feel about this mill 2 years later?

Good vid man. Leaned much sitting on the train. Thanks.

Hi Cody, I am so grateful for your review. I have a question (please); I see this identical microscope on Amazon sold by "DZQ". Is it the equipment the same as Vevor - if you know... I can't find any comparison info. I'm guessing it's just 2 different sellers of the same equipment. Thanks for your help, if can. 🌺

Two things. First and very important. Don't leave the chuck key in the chuck when you aren't using it, EVER! That's a safety issue. Trust me. Bad things will happen if you leave it in the chuck. Sometimes painful things. The second thing is that you don't need different cutting tips to hit different angles. The tool holder and cross slide can be adjusted to the angles you need. I only (mostly) keep my toolholder at 90° when I'm parting off materials. Use the face of the chuck to realign to 90° after you cut at different angles.

You tested before you greased up the gears. If you greased them, did it change the binding any further?

You can make a longer handle, but the vevor doesn't have a great gear ratio. You may consider, in the future, getting a mill that has a 1:4 ratio. I believe the vevor has a 1:2.5.

❤👍🇧🇩

Turned out nice man

I was wondering what my old coworker Cody Dagutis was up to today so I did a Google search which brought me here, to his KZfaq channel. I see you are making the transition from the sales floor to the jewelers bench, seems like a natural progression. This is excellent content, I'm glad to see you moving in this direction, I can't wait to see what you do next. Best of luck - MH

Do you need to use a .5 Barlow lens with this microscope? I’ve been researching budget microscopes and keep reading about needing the .5 lens to increase work area (and it also increases depth of field). No one seems to mention this in reviews of the Vevor. People seem to be satisfied with the distance/work area. What are your thoughts?

17:30 when your trying to line it up if you have access to a laser and can tack it together then flow solder for all the joints it will definitely take less finagling.

Добре чоловік все показав. Але зроби щось з музикою. Не чути, що ти кажеш, а потім музика як заграє, аж вуха ріже

I think you're running into the problems of trying to move involute gears away from their designed centers. If you notice the contact points between gears, the points that they 'hang up' are well removed from where you tried to grind the gear faces. This is a 'cheap' way of giving the machine a reasonably useful maximum stock size. If you really want to improve the gearing, you need to look at a chain drive with a tensioner. Nice review, though! Thanks (don't forget that the same problem exists on the other side of the roller :) )

Would it have been a better idea to pick the thing up and go some room where you can be heard??

Thanks for the video on the Vevor Microscope Cody. I just purchased one of these, and am about to mount it to my work bench. I will be using if for viewing gemstones, coins, and whatever else I think I need to see super close up. So not sure if you're still having the wobble issue with this scope, but I do see something a little unusual regarding how you've got the scope mounting ring and angle bracket assembly put together. The rod appears to be upside down, and the top cup washer is at the top instead enclosing the ball assembly that the scope mounting ring attaches to. Perhaps you've fixed this since you first did this video. I agree that the scope still moves more than it should. It seems that some of the hardware has changed over the last year of so. I have a single knurled plastic knob that goes into one side of the ring. The documentation says there are 3 holes, and 3 thumb screws to secure the scope into. I won't be using the head rest, and the knob that locks the head rest in place is the same kind of knob that fixes the scope in the ring. So I will be using this in the second hole to help stabilize the scope in the ring. I do agree that it would further stabilize the scope by tapping another hole and using this for stabilization.

Great video super motivating keep it up!

thanks for solving my only issue before buying this microscope , that is the working at an angle from the main arm .

Thanks for doing this video. It just popped up as I was researching the VEVOR Milling machine. I am going to pick one up in a couple of days on Wednesday. It will have to be enough to get me started for a while. I will definitely be doing this mod if I have the same problem. Thanks!

What made you get a new one at all?........ the vevor seemed to perform well?

Awesome demonstration and explanation

Would have been nice if we could have heard what you were saying. 😳

What's up cody .good luck on your new job hope to see more videos down the road

🤩 I just ran into this video. Thanks for sharing. Been watching change making videos since forever and this is the first time I ran into someone that’s speaking English that’s making this bracelet. I have a question ? when you put the two bracelets together can’t you hold it with crazy glue I’ve seen someone use this technique on silver and then they just burn it off after sold during. ☺️ excellent video. Thanks again for sharing subscribed👏👏👏🌟🌟🌟🌟🌟🌟😁

that wobble is not a big deal, i use an amscope at work and it has the same wobble

Once the rolls are opened past a certain point this will happen no matter what you do. Have the exact same problem with mine just means there is a limitation on how wide the rolls can be opened to.

That’s amazing work , are you self taught?

представляю какой он красивой

I'm sure they have good insurance or they would not turn you loose with a stone like that or they lied to you and maybe it's not really even a diamond or one that high grade or you have done enough that suited them enough where they have confidence in you. I't been quite a few years since I have done any jewelry making or repairs, I just got sso burned out on it. .

Is that built where you can totally disassemble it, take the top and bottom loose from the sides, remove the rollers and all? Vevor does not have a mill with rollers as long as I need to do what I want so I wondered if I could rebuild one to suit my purpose. Thanks man

Nice video, but worst audio ever

Is the ring stretcher from VEVOR too? Is the rolling mill built where you can take the top and bottom off and put longer rollers on it, like 14" or so long? Thanks man.

Super Bänder aus Metall sehen alles sehr schön aus dass ihr berichtet wie ihr gemacht wir könnten ja bald bei der Post welche schicken wenn ich euch meine Adresse❤❤❤❤❤❤