Really well done and thorough explanation of how to do this. I'm a novice just looking to take care of an apartment wall, but you already made me feel like this task wont be as daunting as i originally thought.

Thank you so much, this was enormously helpful!

How long do you wait before taking spacers out?

Hoa about built in

And that’s how to do an instruction video. No mucking about !

Es aconsejable contar las jambas de las puertas antes de instalar

How about piping on the floor that would be behind the cabinet? Can I cut the base board on the back? I also have a shut off valve that I would need to keep exposed in case I need to shut off the water

Good Video but include the duct work, upsets people when they have to go hunt the continuing video.

Thanks for the video what size sandpaper did you use? How long do you have to work with the glue?

I have a Zircon Studsensor but it will not work in my garage but neither will tapping so I'm ASSuming they have plywood behind it?? (I'm not a handyman). Any tips for garages with no outlets or windows on the wall? I also don't see any nail or screw marks.

Using water-based primer on MDF is fine, been doing it for years. Unless you're buying extremely cheap MDF, you should only have to sand it once and every finish after that should be smooth

*Well, our kitchen is from the 60s-70s, and some of the fronts/doors are glued into it. 😅* What do I do then?*

"Dump the bucket in the neighbors yard so you don't wreck your lawn "......hahaha😂

What do you have between the countertop and wall of where the backsplash is going? I see the cover but is there something specific you are using to cover the back bottom edges? Thanks!

🙏🏽🥰: Thankyou so much this helped a lot …. Have an awesome day.

Im not a professional tiler im a carpenter/joiner but I usually tile the floor and walls after ive installed the kitchen, and I used to grout the way you have just done and i wandered why my joints sunk and even grout pushed in or fell out, until my professional tiling mate tiled a kitchen for me and the worst thing you can do is to go diagonally or in the same direction as the joints, You should go across the joints so that the squeegee flicks the grout through the joints and fills the joints completely and wraps round the back of the tiles and then it can't fall out and especially if water gets through it will run down the back of the tiles and cause damp and then the tiles come loose, especially in a shower,

could i substitute the sheet rock mixture for spackle?

Thank you very much for your instructive video. Have a great day.

How would this door hold up against forceful entry not counting the hollow out door itself like mounting hardware and locking latch? Could it be swapped with a solid wood door assuming extra work involved to fit track.

Love this. Finally, someone can install handles without jig🎉Thanks!

I watched this then removed an upper cabinet with a regular screwdriver in less than a half hour. My kitchen bid wants 16 hrs to demolish 15 cabinets!

Im looking to make a set up myself but not sure how you mounted the panel to the roof and what tilt bracket you used

It goes too fast to see the little stuff!

The jig is the thing! Wow, so easy. Thanks man!

Thanks, Bud. I was about to build an entire structure to support them while I remove them. I didn’t know you could do it in tiny sections. Yes, I am dumb. Have a good one🎉

Do you perhaps have a video on how to apply the glue in tricky areas (under kitchen counter edges, etc).

Good info 👍

Can I do these same tile without spacers, and will I be able to get grout in the joints? Thanks

Years ago, in the land of 220v and wire fuses, failure to observe basic electrical safety resulted in BANG, you're dead...🤪

What was use on the floor joints?

What do i use to stand the door up on its side??

Good clean work . 💯👍

A craftsman at work with those latches

Thank you! About to install my first vent hood and got totally stuck trying to figure out the ductwork. This put me on the right track.

If I remove this, because the guy who did the job left the cut edge jagged. Can I put a new one down and put nails into same holes?

Excellent video. Can someone explain why the LVT cannot just be stick down onto the OSB? Why the need for the hardboard layer?

I didn't mask my plugs, Years ago.When that 110 comes through that wet sponge it will shock the living shit out of you,And you will never leave tape off your plugs again!

Not gonna lie….. I know I’d be tempted to plunge cut the notch with a circular saw

Excellent video. To the point, clear sound, good tips. Doing my first backsplash in an hour so this really helped. Thanks!

addidas safety shower shoes 😊

Great job! Thanks!

Excellent great job thank you.

Why do all the guide videos have ovvious and accecable screws, thrre isnt a single visible screw in any cabinent in my house thats the issue lol

27 LABATTS DEEP AFTER LIFTING IN THE BASEMENT GAINS CAVE AND BOUTTA DESTROY MY UGLY ASS KITCHEN, TY BRENT!

Showed us absolutely nothing

Another dummy

Great review, just received mine from Amazon, looking forward to minimizing the hand sanding!

Thank you. Going to fix my curled shower curtain rod :)

Good video, question how many hours to do that.

I did not see you applying the glue to the plywood or the OSB sheathing. There was one part where you did apply the glue