Bravo. Bonne gravelle. Merci

Amazing work . Thanks for sharing

Thanks. I’ve watched this video at least 6 times😂

Great work,

Can we add some oil ATF on the steering or just grease

Thanks for the video bt which type of steering is this please

great work i see it has a 5 main bearing cranckshaft/block

Nace

Dear, thank you for the video and all advice. I have a 130 defender 2012 and I would like to use freewheels hub too. Have you some knowledge if it is possible ? Thank you for your feedback. Laurent Switzerland

Wonderful engine

off to checkout your other videos

9:20 I’ve got a lhd With steeringlock. Watch for the oval hole in the tube. For me I had to turn the tube so the oval hole is on the uppersite

nice job , i want to ask you ? can i put the oil inside , if yes , what type of oil ? thanks .

Hi mate. I want to make a homemade version of that timing tool as it cannot be bought anymore. Would you be able to help with some measurements to help me weld a correct one?

Muy bien. Tienes vídeo de la misma caña de dirección pero con asistencia hidráulica??

Hola saludos un lanrover de gasolina a diesel trabaja la relación igual

Hi fron panama whet enginer is wanted diesel good steel

Much better than some overly complicated others👍

May have given me the confidence to rebuild my 2 1/4 diesel. Thanks.

Is the steering box filled with gear oil or just grease?

Beautiful, can you do mine now? Please, pretty please…

Very good insructions,I was ripping my hair out on my first rebuild as I didnt place the assembly on its side as you have done in this video.Thank you very much for the demonstration from Australia. Im luvin these landrovers even more now!

Welches Schraubendichtmittel benutzt Du?

This helped a lot with my project, great video! To others doing a reassembly, make sure you get the small bearings seated correctly, one can easily slip without notice, and then you will have to take the entire assembly apart again. Speaking from exp.

Where did you get the non-standard clips from which you used instead of the split pin. . This looks like a great solution for castle nuts in recesses

great video thanks, about to rebuild series 2a box

Da hat aber jemand Ahnung! Allen Respekt. Danke für das tolle Video.

This is a brilliant video thank you!

Excelente video, me ha servido muchisimo para restaurar me caja de timon. Desde Guatemala, Central America, un saludo a la distancia

What type of freelock model do you use

Was für ein wunderschönes Projekt und mit Liebe zur Landrover-Technologie ausgeführt. well done!

Thanks

Do you think a viscous fan clutch would be a good upgrade for these engines? I’ve got a 12J in need of an overhaul at some point.

Thanks, just about to put mine back together

I've got Selectro... All solid casting and full splines. 45 years they've been in place and still as good as new.

Thank you! Very nice and clarifying. You make it look easy. Have you done or planning to do any videos on how to change bearings on the main shaft and cam shaft? If you have/would that would be amazing. Take care! // A

Tremendo trabajo tengo un motor Santana en un Chevrolet 49

Quisiera saber a cuánto se calibra el santana

What grease do you use?

Thanks

NIce. I've got a NAS Defender, but it's rare presence here in Wisconsin. When it inhabits my driveway, it sometimes attracts the like minded. About a decade ago a neighbor, from down the block stopped by and introduced himself. He spoke of his fondness for Rovers. We chatted and when he left, I didn't see him again until just the other day when he stopped by, looking about a decade older (late 70s I'd say). He let me know he had finally purchased a Rover. A Series III 109 Santana with a 2.5 NA diesel,. He wanted to know if I had any diesel mechanic contacts. I do not, and told him so. I saw the truck and it looks pretty on the surface, but he didn't start it up for me. Any resources for free service manuals or likely culprits of a smoky engine would be appreciated so I can pass the info along to him. I loved your video. It's definately my intro to 2.5 Diesels. I want to help my neighbor out. I don't think he's too big on the interwebs though. Any tips would be appreciated.

Sehr gut..hast du goldene Hande

Motorblock du gestrichen welche Farbe?

Better than new. Thanks for sharing the ‘fun’ with us

Very good step by step just the job thank you.

You are the man.... realy helps me with my 58 series 2 stearing issue.

Excellent video. I wish I had the same time and ability plus attention to detail. Thanks for the video.

Thanks. Very clear!!!

Great video and would imagine there is still a big market out there for rebuilt engines like this .

Very helpful thanks ! Will follow this when I'll install on my Serie 3. Question about engaging the 1st gear and 4X4 before securing the nut : do you have to keep it like this to do the second wheel or disengage and then re-engage before securing the nut ? Thanks. Also special tool for this nut ?