If you have an incident that causes a fire and an investigation is conducted, this video will be Exhibit 1.

Looks like you cut it about 1.5 " to short. Once you mark the pipe and put the tape on it you need to add 2" for the insert into the H-Pipe

I have the same tightening noise when I turn all the way to the left and right like sharp turns when leaving a parking spot but when driving there is no noise

86 the spring. Just chuck it in the trash.

So i used a wire brush on my k&n because of this video and it made more than half the cotton come out of the filter. Now i have to buy a new one... Smh. Do not use a wire brush

I knew a kid in high-school who poured gas on an open fire. He was still covered head to toe in compression bandages even years later. Yeah. They did this because of the sadly growing number of us who don't possess common sense. Bring back the Saturday morning PSAs. Good video. !

How's it look 3 years on?

When installing vents into these cans, just use a 1/2 inch hole and it pops in without any difficulty.. I have no idea where they came up with the need for a 31/64 hole. Either America has a ton of crazy fools that need a job designing this thing or there are a lot of stupid fools out there that do not know how to pour from a gas cane properly. Also NEVER fill a gas can from the trunk of a car. Those people are idiots from birth.

The clamps and tweezers Showen on the left are all medical surgical equipment, My wife works for a medical specialist

Thank you for this video. I'll confess an earlier personal experience while removing the 'safety screen' from the tank. As you mentioned, you don't want the screen falling into the can, which is exactly what happened. Obviously one has a choice ..... to either simply let it live in there, or devise a plan to extract it. I chose the latter. After an hour or so of holding the can upside-down, fortunately I was able to shake it into just the right position, and I was barely able to get a grip on the edge with the needle-nose and gently wiggle it out far enough to get a better grip. With 5 more cans to go, I'll be using your method to remove .... hopefully without losing any more on the inside! Your method seems to be the only viable one, so thank you!

Yes Sir

I just replace the spout with the old style (Tractor Supply).

Nope. This should have been an easy 3-minute video. Instead, you made it much harder than necessary.

Gas attendant?? Did you travel back in time? Lol

Great & detailed presentation!

We should not have to fix government overreach.

Great job is much easier to use thanks...

The Guitar string tip alone was worth the watch! Thank you!

Really enjoy your channel. I'm working on a lathe similar to yours. Could you send a picture of the schematic you drew and label the wiring to the switch? Thank you for being so helpful.

Large workshop and pegboard is awful

Liked the first less preachy part 1 version better. I suggest you can the politics and just get on with the techniques.

that flashback arrester will do absolutely nothing to mitigate fire. the device itself is made from flammable meltable material.

I have 2 newer cars and these spouts make it 100% impossible to get a single drop of gas into them. The spout doesn’t go in far enough and the design of the car (ant-siphon?) just makes all the gas spill with none actually going into the car’s tank. Ridiculous!

You’re definitely speaking for me Brother, thank you!!!👍🏻

I appreciate & agree with your opinion. Thank you

Excellent video and excellent calm explanation. I’m going to try this myself Thanks for posting this - Love your work mate

CARB did this in a futile attempt to idiot proof everything.

Why doesn't anyone insulate the box with some aluminum tape,or insulated foam something to reflect heat?

3,700 lbs is the same weight as my 2016 Range Rover Evoque!!

Great video dude.

Remenber many years ago that one dumb man used a US Medal 5 gal. jerry can to poure gas into a hot mower and poured gas over the hot mower ome how .He ended up in the hosptal with 2nd & 3rd degree burns all over his body, His lawer sued US Medal for manufacting a unsafe gas can, whitch put US Medal out of busness, The 5 gak jerry can was desiged to fill up a Jeep real fast during WW2, You should use a 1 or 2 gal gas can to fill up a mower that is cold & never Hot, Then the Feds from consumer end of gov, then ordered all new cans have all this new safety junk in the new gas cans, That dumb guy must have ben a brain surgeon!

The best way to fix it is not to buy the the over priced peace of junk in the first place ! Go buy a 7 gallon heavy duty water container instead liquid gose in in and easely work s for Me 😅

I love the fiskars rake ❤

I think you're unfairly singling out Midwest industries... Well they make kind of a s***** design all the manufacturers are doing this because of government regulations and all of their designs equally suck from what I've seen.

The plastic mesh filter is just fine and I've never had issues at the gas station... I think you could have problems with diesel but whatever.

I love these. They are very easy to use. I guess I'm just not the man you are and hate anything new.

An alternative to heating the can is to use a little Syl-Glyde silicone lube on the fitting.

If Midwest was truly concerned about safety, they would make their fuel cans out of METAL rather than plastic that is easily punctured or eaten through by rats (yes it has happened to me).

Amazing video. Thank you!

Wonderful....to bad a person has to go through all this !!!!

Dios te bendiga siempre

Thank you! I went to fill one of these nightmare cans when I used a gas generator yesterday. I was livid. Gas splashed back when filling a five gallon can. I actually only got close to 2 gallons. I will definitely be modifying that can.

Yup, i got a quote and they paid exactly what the quote said in my case. 2020 Mazda cx5 sold in 2023 with very little miles, impeccable shape. Like brand new.

Hello Mike I got the Cx obd and it doesnt want to connect to the bimmercode app. I tried everything and troubleshooting and it still cant connect. It gives me the "connection error" and to read the manual for further assistance but will not connect and i dont want to buy full version of bimmercode if it wint connect. It seems to connect to the demo version but not the full version

Do NOT heat the can without flushing the gas out with water first! You really need to pin a comment about that, it's a huge potential safety hazard.

Looks like the Amazon Spout Kit was nixed off to eBay

I had a hamburger just now, it was cooked perfectly.

"Filter" - Nooooooo! That's a Flash Arrestor designed to stop a spark (like static electricity) from setting the gas can (AND YOU) on fire. Granted, these safety can's are a Royal pain in the A-s! Remove the Flash Arrestor at your own risk.

I learned the answer when I was in the Army 40 years ago: K.I.S.S. (slang, not it insipid rock group)

I recently bought 2 new gas cans and HATE the new spout. A ridiculous demonstration of so called safety. It makes it virtually unusable. This is not progress in any way, shape, or form.