Hi, here is the link u.pcloud.link/publink/show?code=XZNbQh7ZijhHhzf6MKy0LPUYGVCrkS9oH23k

Because of the high price, mostly in military products, less expensive commercial HDSP0763, HDSP-0962 in early industrial meters and counters

@@dotdisplay1319 yes I suppose so they are mil spec devices after all, I have two 5082-7000 displays in my led collection but have never seen them installed in any products.

pin-out added to video description, display pin-to pin compatible with DL1416 from Siemens

u.pcloud.link/publink/show?code=XZi9viXZ1rYLXt24qC8g8CSya8RjtQA5qDey

Hi, here is the link

u.pcloud.link/publink/show?code=XZ4HtfXZ1CCixf4PxtHVdg8Da6JoKmH6cBnk

Hi, here it is u.pcloud.link/publink/show?code=XZRm1uXZJNNbsLM2ipymDfD2U28gG485l4QX

@@dotdisplay1319 Hi. Thank you very much!! Can share the .bin file also?

Hi, I tested both, Siemens DL1416 and NSM/TSM1416 on this board and both worked fine, hence, they are pin to pin compatible.

@@dotdisplay1319 Thanks much!

hi, here is the datasheet, resistors are not required, it is 5V TTL. www.datasheetarchive.com/pdf/download.php?id=ae22dc78b76b73c51fef15e0ebca853f6cbad8&type=M&term=50827010

No resistors required, pins are TTL

@@dotdisplay1319 OK, thanks

Hi, here is the link: my.pcloud.com/publink/show?code=XZX11R7Zj54RlHy48CmDUG660SgUjJYhRkK7

PS temperature and humidity sensors not connected

@@dotdisplay1319 Thank you for providing the archive with information, I will be happy to repeat Your project. Tell me this firmware does not use a temperature and humidity sensor if I understand you correctly?If you do not mind please tell me how to install the fuses bits for this firmware

@@alikangel Yes, because tube driver heating the board and we have wrong temperature readings.

@@dotdisplay1319 And if the temperature sensor is taken out of the Board on the wire, it will work?What is the size of the printed circuit Board you got? If possible please write to me by e mail [email protected] so I can talk to you. Thanks

Seller provided me manual with pinout

It is a soviet clone of Burroughs

Arduino is the best for testing purposes

@@dotdisplay1319 do you have the code for this?

Hi, I just modified little bit code for 4N51 displays my.pcloud.com/publink/show?code=XZesXmkZPQnEBD6AubYWFaQ7X7ynYbJVcQ5V

Any 5V GPIO MCU will be fine, Arduino for example

Arduino or any other 5V TTL compatible MCU, CY8CKIT-042 PSoC® 4 Pioneer Kit for example

my.pcloud.com/publink/show?code=XZfeXl7Z9JLvoxOrBQLxmfoI1Mi1mQGwHx8k

Hi, here is the display lib. my.pcloud.com/publink/show?code=XZfeXl7Z9JLvoxOrBQLxmfoI1Mi1mQGwHx8k

Hi, I'm using Arduino mini in this project, here is a parsing code for date section: // receiver status array // 0=leapsecs, 1=tfom, 2=10M, 3=1PPS, 4=ant, 5=hold, 6=nsat, 7=state, 8=year, 9=month, 10=day, 11=hours, 12=mins, 13=secs, 14=day of week // 15=survey, 16=numsat long unixdelta = 315964800; //delta between GPS and unix time valPosition = strtok(dataBuffer, delimiters); long secs = 0; if (strcmp(valPosition, "CLOCK") == 0) //have a clock message { valPosition = strtok(NULL, delimiters); secs = atol(valPosition); //time in seconds valPosition = strtok(NULL, delimiters); data[0] = atoi(valPosition); //leapseconds valPosition = strtok(NULL, delimiters); data[1] = atoi(valPosition); //tfom Time figure-of-merit (1=good, 7=bad) secs = secs - data[0] + unixdelta; // subtract out the leap seconds, add in the unix to GPS epoch delta data[8] = year(secs); data[9] = month(secs); data[10] = day(secs); data[11] = hour(secs); data[12] = minute(secs); data[13] = second(secs); dataBuffer[0] = 0; }

Remember than MANY older GPS Receiver outputs will NOT have correct date, WNRO issue (after 2017). Majority of the mfg. (like Trimble) never offered firmware upgrade. This can be corrected, BUT you must do the correction with your external software. TruePosition used Furuno (Japan/South Korea GPS rcvr). === ALSO Lady Heather Source Code is available .... for Algorithms you lack. EEVBlog has a running discussion and other TruePosition owners requested information for refinements,

Yea, i got my date issue figured out. Unit is still running strong. Might get another as a spare.

Not sure that I understanding you right but you have to adjust trimmer capacitors inside of the 6669 meter to match display readings to 10Mhz from GPSDO

What do you mean? You can use info from this datasheet datasheetspdf.com/pdf-file/619020/NationalSemiconductor/NSM1416/1

Sorry, but could you give a full datasheet (which indicates the purpose of the conclusions). Thank you in advance.

MikesMovies not anymore, they took them away

my.pcloud.com/publink/show?code=XZNbQh7ZijhHhzf6MKy0LPUYGVCrkS9oH23k

Please, check your ebay mailbox.

I have some PCB’s from this project but you must have SMD soldering skills to complete it. The most tricky part is micro-USB connector. Firmware available for download.

My soldering skills are not exceptional but they are not horrible either. I could probably get a few practice projects going to sharpen my skills and be up to speed.

Ok, sounds good, I can create ebay listing for you, it will be 10USD for set of 2 boards + shipping with tracking usually 10-15USD to US or Canada. Let me know if you ok with that.

That would be great!

Do you need IV-9 tubes? I have extra 6 for 17USD.