Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
Пікірлер
@Grace-pv8dz 4 ай бұрын
Hi,dear,Do you need a forklift forks? I am a manufacturer of high quality forklift parts
@HonestEvolution795 4 ай бұрын
So how do I find the year?
@atlastoyotamaterialhandlin5665 4 ай бұрын
Check out our blog post maybe this helps you: www.atlastoyota.com/news/what-is-a-forklift-capacity-data-plate !
@Mbm-billiards 5 ай бұрын
Very helpful thank you
@SaviourSeha 7 ай бұрын
👍👌
@stuartharris5693 8 ай бұрын
Perfect video: short and detailed, a pleasure to watch!!
@jimmysavage4198 8 ай бұрын
Is there a special button on this machine to get both brushes spinning? I have the same machine at work but only one brush spins. The left one. My employer said that there is a button on this machine that makes both brushes spend that I cannot locate. The machine I have though it does not have a display of any sort or buttons it's a very basic machine where you turn it on push the handle to go which engages the brushes at the same time.
@atlastoyotamaterialhandlin5665 8 ай бұрын
Hi @jimmysavage4198! Great question - Activating the Brush Switch "on" enables both brushes to spin and then when you push the "Fwd/Rev" button to propel the machine, both brushes will come on. If they don’t, you should check the circuit breakers to make sure the breaker for that brush didn’t pop out due to drawing too much power. The Circuit Breaker is a series of white caps below the operator handle and, if one is popped, it will be sticking out further than the others. You should attempt to push the white cap back in with the power turned off and then attempt to scrub again. If this doesn't work, you probably have something more involved electrically preventing the brush from spinning. Hope that helps!
@jimmysavage4198 8 ай бұрын
@@atlastoyotamaterialhandlin5665 the whole tank left open and there was some fuse buttons that had to be pushed never even knew the tank lifted up
@johnnyboy4me 10 ай бұрын
I have oversized heavy forks and have knocked 1 fork off several times and used wood blocks to get back on carriage . Its a bitch doing this solo because of the weight of the fork and lifting onto to wood block . You have to be mad and determined to get the fork to an elavated block but can be done. That said i can't stress the importance of the block height being accurate to successfully getting fork back on carriage . If pallet is correct height its a great idea and I'll be trying if i foolishly find myself in the situation again. Thanks for sharing
@jonk9957 Жыл бұрын
Just did this at work using 2 reach trucks and alot of back, worked but knew there was a better way, found this video and feel disgusted with myself for how easy it could have been 🙄🤣
@HartmanHovic Жыл бұрын
Thank you. Best explanation of this on KZfaq so far.
@AhmedA-cm6me Жыл бұрын
Thank you much dear Tim. ❤❤🇦🇪💐
@fandangololo1855 Жыл бұрын
The levers are too close together.
@1ton4god Жыл бұрын
Can anyone tell me how to get a pin off the sheared off in the poor for forklift lifting arm. How do you get it up out of the notch?
@razorramon8326 Жыл бұрын
I remember using this back then at Target and Walmart supercenter. It was a Crown Brand. the name of the machine called "The Wave". (Work assist vehicle elevator)
@abdelkhalekelbikam3929 2 жыл бұрын
Your email address and phone number
@mechanicforklift6370 3 жыл бұрын
I like your forklif
@ridenacott 3 жыл бұрын
I don't work for atlas however they are the best in chicago. Also they have a great reputation, From one forklift mechanic to another