Thank you!!! I followed your video… Even with the 3 buddies who didn’t want to help. Got to the switching wires…. Then was over it… I’ll keep you posted if it helped or if I just threw the thing over the patio…🤣🤣🤣 Thank you!

Thanks! Great fun to find your video! Mine goes in spurts from being fine to overflowing several times a day so I may try this next time

Dude is steady out of breath.

What’s that thing called so I can order it?

Before u order or buy anything try this my heater kept shutting off showing e90 code I changed and put new filters in heater works fine worth a try johnnymoondog thx

I looked through many videos, and none of them helped. That's until I found your video! I was able to fix my water dispenser in just a minute since I had already taken it apart, just like yours. You just saved me about $200!! Thank you so much for making this video!!

Thanks for the vid. Everyone seems to say it worked but I'm afraid to try it. Any reason this works? Did you find this hack somewhere?

Thank you for the great instructions. My Wife and I were about to purchase a replacement water cooler until I watched your video. The Primo instructional video did not mention this and claimed that I had to contact Customer service, thankfully I found your video and was able to fix the issue.

You were a big help. Appreciate u taking time to explain your situation.

Thank you

Thanks amigo

I know this is old, but it still works! Thanks! Can't believe there is virtually no other info on this outside of your video, so kudos, sir! And your three friends? No cold water for them! I have a theory as to why this works. There are two floats on the switch in the cold water storage tank. Under normal circumstances, when the bottom float hits the lower position, the tank begins to fill. When the top float rises to the top position, it signals the tank is full, and shuts off water to the cold water holding rank. Again, under normal circumstances, if you only dispense a small amount of cold water,, enough to lower the top float, but not the bottom, no new water would enter the storage tank. Only when it gets close to empty would it fill. When the top float goes bad, either in the float, the wiring, or the circuit board, there is nothing to shut it off and water exits via the overflow. By switching the wires, you are essentially telling the dispenser that the bottom float is now the top float. I can't (won't, don't want to, etc) work out the circuit design for this, and maybe it's just happy coincidence on how they designed the circuit board that it DOES work, but it does. The outcome of this is that the unit DOES function, and should until the bottom float circuit malfunctions in some manner. There are two things to be aware of 1) the unit begins to fill again immediately upon dispensing (not sure if this is typical of the "normal" unit as I inherited this one with the overflowing condition), and 2) the cold water storage tank will never fill completely to it's previous "normal" level, since it's using the lower switch to turn off the inlet flow. So you're missing an inch and half of chilled water in the tank. A sacrifice I can live with. Again, big thanks to the original poster! I was beginning to think that Brio and Google were in cahoots to suppress valuable information, but here it is!

Love this video I have the same dispenser, but my compressor is not turning on. The water only come out as room temperature, can you make a video to help me out 😊

Top notch video. Showing the homies not helping reminded me of my homies 😂

You never said what that little heater cost?

God bless you.thank you for showing

Heck yeah! Thanks! Those primo videos didnt help at all and i decided to trust you before reading these great comments and it worked like magic! Thanks!

Sir, thanks so much for saving me a couple of hundreds dollars. I tried to fix it and i knew it was a wire-issue (but didn’t have a solution)because all my connections and floaters were working fine.

Sometimes you only need to descale the hard water deposits from the system that builds up in the heater. You can buy temperature sensors for your spa if you need a repair service manual this tells you how to repair your spa. I’ve had my intex spa since 2014 and still working.

THANK YOU SOOOOOOO MUCH....

Where is the link to the Amazon item or name please

20 thumbs up! You fixed my problem, Thanks!!!

Your video helped me plug the pump in the correct port…I took off the old pump and forgot which port it was connected! #SMH. Thanks !

YES! That’s what I’m talking about! I would put a thermostat on that heater to make sure you don’t over heat the water past 104F.

Interesting. I am not getting the sucker to work so I am currently trying to replace the pump. I got into the guts, this video helped, rewired, but I don't have enough strength to disconnect the primo pump connectors in the bottom lol. SIGH

Thank you for sharing.

What the hell is the brand and what is it called?

Thank you so much for posting this! Worked like a charm.

Your instructions worked for me too! Great! Thanks!

The is for your video although it made me laugh when you showed your buddies standing there looking at you like your crazy 😂🤣😂🤣😂🤣. But you did better than primo they was like if the instructions they gave me dosen't work then I'll just have to purchase a new pump. Like hell no

Loved your video! And it worked! I appreciate you saving my dispenser from the scrap pile.

shit has me dead

How did you remove the water holding tank?

Thanks sooooo much

Mine does that but it's very random sometimes I can go a couple of bottles and no leaks then it will leak any thoughts ? Do you think think it is the wire issue or possibly the float or something else? Thanks for the video

I suspect your heater is just plugged- I was getting E90 code and simply used a screw driver and toothbrush to clean out! They get clogged after a couple of years. All is good!

"I got three buddies over here that didn't wanna help me" - isn't that always the way? Thank you, random stranger, for being more helpful than any three buddies.

Thank you helped a lot

Cannot put 2 of the 1500 watt heaters on the same circuit. It will trip the breaker.

I switched the wires yesterday, No more leaking overflow since then. Thanks Lloyd, Great video!

Have u lost ur mind, you have this heater hanging over ur hottub powered by 120 volt outlet with no fault control whatsoever you are going to fry urself are sumbody else, plz for gods sake stop this now.

Great tip....I'm going to order it right now. Thanks 😊

Thank you for sharing this video. I have the same model and it will release hot water on its own, through the over flow. Gonna try this! Thanks again😊

Hey there! I'm trying to disconnect the pump wires (red and black) from the mini board inside the metal box. Is there an angle i should pull? They're so damn tiny i cant get a good hold on them lol thanks for a nice video btw!

Yo! You’re better than freaking Primo Customer Care! They tried to get me to buy a new one, but your instructions worked BETTER! Thanks a million for this!!! 🙏🏾🙏🏾🙏🏾

What heater is it?

Awesome! your tip helped me solve my problem! You are great! Thank you so much!

Thank you so much bro lmao you have no idea!!! 😂🤣

Lloyd. You are a savior. My wifey loves me lots more than yesterday. Big Thank you.

I feel like this company owes you money.... you literally saved 20k people worth of refunds lol.... this video will fix your problem... pay the man 💰