Where do you buy the OEM seat covers? I can't find any.

You talked me out of buying one, thanks

In in norway they get big like REALY big easily 100 feet and they easily grow 4 feet a year and they self seed. In norway most forest's consist of norwegian spurce beacuse they out compete most other trees. in norway kids like to eat the new yellow shots, eat them before they get to hard, the shots have a bitter/Intresting taste

You're fast ! Thanks for the video, it might help me replacing the black plastic, I replaced the motor with out popping out the vent , and I can't get it back in place to align with the screw Holes,

I did it in 10 hours or so. I’m hoping the other side goes a lot faster.

THANKS, Now I can attempt to do the change. Great, to the point video. Greatly Appreciated.

Great Job!! Thanks for the video!

I wouldn't buy a new one, it'll probably just break again. Your fix is probably better than a new one.

That isnt your falt i v broken or should i day that the loaded bracket on my 3510 has broken twice on both sides It is a engineering problem and kioti redesigned the brackets and bucket ac Assembly in 2021 sp they you have it and i v contact thr corporate office and they refused to let me see a representative. I'm picking my tractor up for the fourth time of replacement of the bracket as you told me too hard on equipment that's three-quarter inch steel bucket assembly, and pistons blown out or bent before that bracket broke never buy, Coyote.

Great video! Do you have a hand drawn schematic of how you wired it from the battery, to the switch, and to the future sprayer? My Dad suddenly passed, and I am trying to troubleshoot how he had an airblast sprayer with solenoid valves hooked up. I didn't pay enough attention while he was alive. :( Thank you so much!

How do you pick which type of oil? I live in Tennessee Appalachia. Probably use the tractor more in the summer than the winter but I do use it in the winter as well.

10:21 - Mentions his choice of oil, 15W40 Diesel Engine Oil

Where do you get the gaskets from?

this is a very pleasing video. wondering how the Milwaukee held up over the dremel?

A la piedra sólida no le hace ni cosquillas

Where do i find this part please ive been looking everywhere

It's looking good

Your arsenal looks like mine! I have mine "hidden" as well. I like the use of the scrap and the trim you did. I have big pines on my property and will use one for the main beam. I like that you used a lot of wood from your property. On my solar, I underestimated what I needed for an invertor. I got a 2000watt and next time will get a 3000 or 5000. Good job and looking good!

Did you offset your seams on your headers or did you just double them up?

Wonder if anyone explored who made the clutch - and if there are other replacements from same or other manufacturers.

I honestly laughed out loud when you checked the other side of the 6x to see if the nail went through!! Thanks for the info. I finally bought some land and will start building in a month or so. I think I'm building a monitor barn, so I'll be checking your videos often.

Question: Is Kioti any relationship to Kubota? Anybody know? Reason I'm asking is because I just replaced the front axle seal on a Kubota 3710 and be damned if it is almost identical to this Kiota. There's very little difference. It broke down the same way. The only difference I did was since it was just the steering seal leaking on mine, I took off the whole assembly from the bottom so I wouldn't have to break the hub seal. Oh, and Kubota has a big O-ring for the hub. I noticed that on this Kioti it didn't have one. Anyway, good job on this video. Very informative.

nice build!

I was about to go to a dealer, 45 minutes from me, changed my mind. Back to decide between NH, JD or Kubota. Kubota on top of the three.

It's funny, my Toro lawn tractor, does the same thing, but much worse, actualy got worse with time. Same pedal system. My 2003 Kubota 850 hours, still work8ng as new.

Is it normal for charger to go to 13.7 volts than after 4-5 minutes it goes to 12.6 for about 1-2 minutes?

I see you are in Michigan. Same here, North of Sandusky.

Great job. In the process of a 5x5 on 12 foot 4x4s. Doing this alone so, Will be assemble walls and roof after standing base on stilts. With 4 wheeler and tow straps. Should make a video. LOL

Looking great! I made my countertop in my truck. It was fun. I like the way you made the cabinets. I just bought some land in Georgia, so I'll be using a lot of your ideas. Again, good job. What batteries are you going to use for your 12V?

This is the best video I found so I can see where the snap ring is. Thank you for the great camera angles and lighting. Excellant job.

Not surprising… the cabinet turned out great. The cedar ceiling boards have a lot of character… everything’s coming together! Very exciting time for you (and us watching too)! Thanks so much for sharing this with us. 😊 Better get a move on… will be time to get skip dog outside before you know it! Planting season! Thanks Andy. Derek & Michella Payne

metal roof all . snow loads

when i added my collar ties , set them at 1/3 of the length ( ridge board to outside plate) just saying, not sure if i needed the xtra lngth. love your channel .. happy trails happy build.

Well I am ready to change my tractor's oil...I always say if a guy can do it then I know I can and this is way easier than I thought! Thanks! A 71 year old gal!

nice looks good time to get that wall hanger happy hunting

I appreciate the video. I was getting ready to hole saw a hole into the strut tower. Not really, but this video helped put me at ease about swapping the solenoid.

gonna need some good solid roof caulking around that cutout for leaks. Don't forget to clean that stove pipe out from on top of the roof each season with a chimney brush. Overall good job in my opinion.

Great job. Clearances to code are so important. Trust it will work well for you.

that place is gonna be toasty

Very cool idea and you used scrap. That's always nice.

I love your barn.

Looks good. Would hate cutting a hole in my roof!! Good job and very informative.

Thank you for this video. You made this more clear than other videos I've watched. Same seal leaking on my CK3510.

Where did you get the picture from?

It’s probably not the popular favorite- but I like the way the strait side by side looks over the corners with the 45s. Great work as always! Moving right along you are! 👍 (That live edge trim is gorgeous!! )

How have they been holding up?

Quick question, how much did you have in on the Epoxy and clear coat? And where do you get yours? Awesome job on coasters and the bench. /cheers

Looking good let us know the outcome.

I'm jealous... Did you get an architect and engineer? How much?

Awesome review- thanks! 👍