Thanks. FYI - It's actually a requirement in AS 1562.1:2018 section 4.8.3 to fix on upper and side. HB 39:2015 section 8.7 shows the use of concealed fastening clips for side so fixings are not visible.

I have a question that I'm hoping you could answer please. When laying blanket for a steel shed, do you lay one continuous length from one side to the other OR do you cut it in two piece so this can provide ventilation through the ridge capping ??

Which side is the right one to face up? The shinny or dull?

Yeah but how the hell do you join it using this process when you're attaching two ends together on internal clips. Can you just hitch and unhitch the quad gutter from the clips?

Do you have a video of roll top ridge installation on a hip roof where the three ridges intersect? Thanks in advance.

Are ALL profiles 762cm wide?

You shouldn’t be using a impact gun on a roof because it removes the paint on the screws, use a normal drill instead

thankyou for a great video. cheers.

Whats the drill bit you used for this? It looks much shorter than a normal drill bit, and better than carrying a screwdriver and a drill around!

Imagino que está en EEUU,no entiendo ese sistema de montaje para una cubierta y menos alli con la de huracanes y demas que pasan por alli,aqui en España no lo aconsejaría a nadie,por muy bien pensado que este y como dije no entiendo que se utilice alla

Water blows inside sides, some sides are not strait angle so they don't connect together well, have to force connection, you pay $1000 for this, you'd expect more, steer clear away from this gimmic.

I get a bit of blow back (if that’s the right wording) under the end of the sheets. You can see the staining on the timber from the water where it tracks back from the end of the sheet where it over hangs the gutter. I have a 10cm fall over 5 meters. What is the best thing to put in place to stop it or how do you bend the end of the sheets down on the lower part of the corrugated sheets ?? (Love the videos by the way)

Malaysia

Does it work without the metal sheet to support box gutter?

how do you do a skillion roof corner ?

Nicely done. One thing I noticed is in a previous video, you suggested putting rivets in from inside the box becasue the look better while here, you put them in from the outside. Any reason?

Hi , thanks for the video , do those bugle screws need to be for external use ? , I think it is something you should mention .

Bro you are a joy to watch wish you could show some box g, sumps, ect repairs

Would you use these clips to mount guttering to a Colorbond custom orb shed? and tek screw into the custom orb?

Ripper video. Is this the same theory if cladding a wall in Colorbond in corrugated iron?

Thanks for taking the time to inform us, very valuable information.

wrong way to upturn the roof!! You just left a tear on either sides to leak. Solution is to use short width tool to allow metal to naturally form without sharp bend to minimise tear. Been doing properly for over 20 years in Sydney

Thanks for sharing. Good to learn.

Could you use sikaflex instead of silicon

Thanks for the video. I am struggling to install gutter to brackets. After the gutter hangs like in the video, when I go to push in, one brackets unclip from the gutter lip. Any advice to help with this issues.

would you put any thermal blanket under these ?

when tapping edges down wouldn't you want to use a non metal tool ?

😂😂😂😂samual l jackson..twot

The cost to install a box gutter is insane where i live, I'm hoping you can upload a box gutter installation video.. i have an idea of how to do it, but your videos have taught me a lot!

Nice to see one built. Also from watching Site Inspector, the bottom of it has to be supported.

Excellent tutorial!!! Impressed.

That’s not flush is it 🤦🏽

Aussie cowboys

comments about measurements and screw types would be good thanks

Cant find those brackets anywhere , any alternative

The video is well done but the information and why this and that are done is a little on the light side. I realise the guys are not trainers but there is a lot more as to why certain small details are carried out.

is it worth running the metal mesh under the foil, or not needed?

Nice video. Why is it called a Quad gutter ?

great video of the back of your shirt

Gotta trim the corner off the underlap, at the bottom of sheet, when installed at lower than 5 degree pitch.

in real life tradies will glue that with uhu

can you join gutters when they are on the clips? I have 12mtr gutters but 2 lengths at 6.2 and a 6mtr length.

Nice video mate … 👑

Legend

What's the true width of the sheet, were it flattened?

Another informative video Darren; the best roofing ones on the net, unreal. Thanks heaps 👊

Thanks Samuel L Jackson! Rock on

Never back lap sheets

Should be fixings into a purling and you’ve no lap tape wither.

What’s it called when the panels come pre flashed like that?