darryl mce. Thanks Darryl. I appreciate your support 😁

Cheers Dave 🙂🤙

Thanks for the feedback! We will put the apron flashing video request on the list!

Thanks Kadir 😀

Hi Caspar, thank you 😊. Best of luck my friend 🇦🇺🇦🇺

@@metalroofing7210 Thank you for noticing my comment.. Likewise my friend. Kee,p safe always especially we are on top of the building..

Thanks for taking the time to comment, sorry that you had trouble with the markings. We will do better on the next video!

quoc lien . Hi Quoc. Thank you for your feedback. I believe the part of the roof in the background you are referring to is the apron flashing which I have fixed to the wall and siliconed up the top edge. 😊regards Daz

Thanks for the feedback! We will put the half round gutter request on the list!

Do not put screw on the drip edge like the example in this video. Go about 20mm above the crease before the drip edge. Screw laps and centres make sure you flick a line for straight screw lines. The example in the video is wrong

David Robinson hi David. It does take quite allot of practice before you can put the screws in without the drill slipping. It would greatly help you if you just pre drill all the holes first. 😊 regards Daz

Hi Gareth. I like to tighten the screws up and give them a spray with WD40 every couple of weeks. If you’re using them everyday they normally last around 3-4 months

@@metalroofing7210 the nan. Thanks

The man 😆

Autotrope if you would prefer just to use screws and no rivets it’s up to you. There are no set rules for this

Exactly as I said

I also curious. I want to know if rivet safe to leaking

Hi there. You are right it is purely for aesthetics purposes that I cut it on the angle. If you prefer to have it square with the barge then that would be fine also 🤙

The video is great but I have to disagree. The lip on the roll cap means that if you run it straight, there will be a slight gap on the end. It’s just poor work. Cutting it where you did in the video allows it to sit flush, and be sealed and riveted water tight. You can still run it straight but you should at least trim the lip off where it travels above the barge cap.

Fortunately where I am located, we do not get the extreme weather which it would require for the wind to drive the rain through the small gap in the corrugation up hill on a pitched roof to make it over the end of the sheets. If you do live in a location which does get this extreme weather then you are required to scribe each side of the ridge capping to sit down into each corrugation so that there a no gaps. As for the guttering getting blocked and the water backing all the way up the sheets and under the ridge capping!! This would be impossible because the gutter would just overflow either over the front of the gutter or over the back of the gutter. Hopefully you would gone with the gutter with the overflow slots and the water spills out the front of the gutter causing less damage

@@metalroofing7210 terrific thanks for the response and clearing that up

Hi is wa. It is best to silicone between all joins when installing roofing that needs to be 100 percent water tight

johny ubankta hi Johny. Thanks for your feedback, I agree that it would look a little neater with those tabs hidden. Good luck with your roof. Kind regards Daz 😊

Thanks Steve 😃🏄‍♂️

Pink Roofing. In my experience I have found it far easier to line up the roll top ridge and get all the crease marks out of it with firstly just using rivets. Then once you have it perfectly in place then screwing it off. trying to do this with just screws from the start usually results in crease marks which look unsightly. 👍

@@metalroofing7210 from my experience stripping old roofs that these rivets will become holes and the first part of the roof to fail. It's not about easier, it's about making it work no matter how painful. Any ideas that make it easier and subject to failure are a fail in there own right. Where a rivet is placed there should also be sealant as a gasket. Happy days

Chris DownUnder Hi Chris. The rules for installation of roll top ridge change depending on which state you are working in. This video was shot in Victoria. It is considerably quicker when you don’t have to scribe 👍😊Daz

Warren B. 😂👍agreed