Patrick McCurry

Пікірлер

@tomadam9887 13 күн бұрын

Dziękuję z polski :)

@miguelmoram1506 24 күн бұрын

Are you guys still selling this fairings ?

@momobestE 2 ай бұрын

Hellow, Nice, this bike has ABS? Thank you.

@pietervanderweij4855 3 ай бұрын

Great video

@MotorcycleMayhem595 3 ай бұрын

I sure could use some help with a basket case 2009 FZ1 that has been sitting for 8 years with fuel inside the tank.

@buelle109 3 ай бұрын

Funny you say that. I recently had to go through my FZ's fuel system because mine had set for about two years. There are tons of videos on taking care of a rusty tank with vinegar - which is what i did. And i also rebuilt my entire fuel pump. Total cost was about 100 bucks. Did some other stuff like new coils and plugs but my FZ runs like new.

@MotorcycleMayhem595 3 ай бұрын

I may do some videos of my restoration.@@buelle109

@andreasholz9380 3 ай бұрын

Sehr gute Anleitung, bitte Kommentare auch beachten. Beim Ausbau den Rotor am besten durch die mittlere Öffnung gegenhalten.

@alexandrn6426 5 ай бұрын

Пиздоглазые ублюдки, такую галдость подложили

@DaRuler66 5 ай бұрын

Still noisy 🤣

@MuftiBikes 6 ай бұрын

is it still safe to order? why can i not find any pics of bikes with this kit on?

@buelle109 5 ай бұрын

Yes we're still making all the FZ1 parts. You may find pictures on one of the FZ1 forums

@chargerification 8 ай бұрын

Have you ever found it necessary to change the seals at the bottom of the top stacks? The ones in the air box, above the throttle bodies. Thank you

@kooshaspels8401 8 ай бұрын

Kunt U mij zeggen waar ik de map van ivan kan vinden,en kan ik die dan laden op mijn pc5?

@the3hrdoption637 9 ай бұрын

what kind of protection does it offer when it is raised? Does it ever provide wind protection?

@fenderfan8543 10 ай бұрын

Power commanders are a waste of time these days. You can just get the ecu flashed and make all the same, and more adjustments.

@IndustryPets Жыл бұрын

This was awesome! 👏 great job!

@colstonjames2328 Жыл бұрын

Trying to learn how to do this to my gen1 is it the same????

@scorpion-ninja8228 Жыл бұрын

Hi, if I dont mount the nose cone, will it alter the airflow in any negative way? Will I hear more wind noise, etc?

@KTHKUHNKK Жыл бұрын

I am glad to see you're still making videos. Believe it or not I'm still flying my typhoon h480 Keith Kuhn

@KTHKUHNKK Жыл бұрын

Very cool video.. As a video maker myself I know you went through quite a bit to make that video. Darn cool. Keith Kuhn

@AndrewPinkFloyd Жыл бұрын

I just stumbled on your channel. Your videos are incredibly done. I am astounded by the professionalism and production quality! I'm looking forward to watching more of your H+ videos since that's what I fly.

@deegaw11 Жыл бұрын

Are there any symptoms the bike will experienced if it was failing and coming apart? I just bought a 2014 fz1 with only 6k miles. I’ve only had it for couple days and haven’t ridden it much yet but during a cold start it would take at least 2 tries but once warmed up it has no problem starting. Previous owner said it wasn’t ridden much and sat for awhile so I’m not sure if that has to do with it.

@michaelfrederick1271 Жыл бұрын

Do you have to break out that cat or can you leave it if your just adding a shorty pipe?

@OllieAlston Жыл бұрын

It would take me months to learn how you do the videos you post.........G. Wizz......and your bike looks way cleaner than mine.

@OllieAlston Жыл бұрын

Great video.........like your work. Air filter ........what's that ? 😃 Your air box was way easier than taking mine out of my FZ1 a few years ago. But after gutting the cat and removing the X-up n silencer she sounded Raw especially when wound open across the bridge headed to Tampa. ;)

@nickbouvy6524 Жыл бұрын

I suppose the MAF tells the ECU about the extra air going in and it doesn’t run lean

@dimidrone Жыл бұрын

Interesting footage! New sub here!

@danbayne1007 Жыл бұрын

That was fantastic. your creativity, editing, and production value were awesome. Thanks for sharing. This should be required viewing for new drone operators, attached to the TRUST test, lol.

@AirDigitalDroneServices Жыл бұрын

Tremendous video. Well done. Loved and subbed from Canada.

@buelle109 Жыл бұрын

Thanks for the sub, more to come

@safidrone Жыл бұрын

Wow it's been a long time since I've seen videos on your channel !!! I love this little movie...🥰🥰 Welcome back to the channel !!! 😊😉 Gérard

@buelle109 Жыл бұрын

Gerard, yes, it has been way too long but I am back and eager to start making a lot more videos. Thank you for watching and commenting.

@safidrone Жыл бұрын

@@buelle109 Great Pat !!! I am eager to watch...😃 You are welcome 😊😉

@independentdronechannel170 Жыл бұрын

🤣

@renzotamborini3415 Жыл бұрын

Ahh ahh..great Mark!

@buelle109 Жыл бұрын

Thanks for watching, glad you liked it.

@GreenWitch1 Жыл бұрын

I’ll bet this is a true story 😂

@buelle109 Жыл бұрын

@@GreenWitch1 It's true, Mark can't stop running stop signs. 😉

@GreenWitch1 Жыл бұрын

@@buelle109 😂😂😂

@MomentofZed Жыл бұрын

I thought that was Brad Pitt until I saw the credits! Nice job- well done!

@buelle109 Жыл бұрын

Hahahahaha and I think that is Tom Cruise as well😜

@jayminasi6073 Жыл бұрын

is this a generation 2 fz1?

@buelle109 Жыл бұрын

Yes, 2007

@jayminasi6073 Жыл бұрын

@@buelle109 i take it that my 2004 is still possibly liable for the stator damage.

@vicpnut1 Жыл бұрын

@@jayminasi6073 I believe gen 2’s start @2006. And later gen2’s( not sure how later but like last yr or two) had a from factory “fix” , meaning they changed the design

@DaRuler66 5 ай бұрын

@@vicpnut1 what about the 13 model ?

@vicpnut1 5 ай бұрын

@@DaRuler66 i wanna say that yamaha finally fixed it by 13…but its been awhile and i cant recall specifically ….also just did a quick search and now specific years came up just how to’s and sales etc….i know i read in one or more forums im in of a year they finally fixed it ,all i can remember is is was way after they knew about the rotor failure ,like last yr or two of production..

@AlexZettl Жыл бұрын

best Video ive seen so far great ammount insight knowledge

@TheTruthWillBRevealed Жыл бұрын

Hey bud, it's too bad you haven't made any videos lately. I hope everything is 👍 with you and your loved ones. Come back soon.

@buelle109 Жыл бұрын

Thanks for reaching out. All is well here and in fact I have videos in the works as I really enjoy making them. Stay Tuned

@antonioscreenmaster Жыл бұрын

Эту хрень делают из 2мм оргстекла, соответственно очень хрупкого) а не поликарбоната. Со временем от вибрации и сопротивлению ветра пойдут трещины 100%. Пока крутил в руках, чуть понажимал около отверстий, пошли трещины. При падении всё может плачевно закончится. Естественно никакой сертификации тут быть не может. К рамке вопросов нет. kzfaq.infodL4xvEIBrLY

@johnnykawakid Жыл бұрын

Can i buy this over here in the uk?

@buelle109 Жыл бұрын

Yes www.copperdawg.com/

@Nortonsnorton Жыл бұрын

@Patrick H o l y ! I see this video was made 5 yrs ago, well my H could use some fine tuning so I’m eager to make these adjustments. After reading many comments here I will first make sure my joystick(s) reach 100%! I do have a question though, this might seem odd, maybe not. I’m finding the H takes forever to descend, is it possible to change that rate curve allowing for a speedier descent? Right now it takes 10 seconds to descend 100’. I find that terribly terribly slow.

@KTHKUHNKK Жыл бұрын

Patrick can you please tell me in the rate curves. I set all values just like you suggested. How do I set the values to even slow it down a little more ? Thanks. Keith

@Nortonsnorton Жыл бұрын

I know the answer! 😼

@KTHKUHNKK Жыл бұрын

@@Nortonsnorton I want to make it even Slower. I put in the exact numbers he did.

@MrRobbieG88 Жыл бұрын

Hi, great tutorial, it always baffled me how did Yamaha build a such an amazing machine and decided to completely cut corner in a name of whatever by introducing this prone to fail concept....

@69Fancylicker Жыл бұрын

Are you still trading and do you ship to the UK your mods on the Fz1 are badass

@buelle109 Жыл бұрын

Yes we are and yes we do. Check us at copperdawg.com

@69Fancylicker Жыл бұрын

What sort of mileage are these failing?

@buelle109 Жыл бұрын

Don't think it is as mileage related as one would suspect some bikes got it as early as 10K some are over 40K without a problem.

@Bikechaska Жыл бұрын

Hi I have Fz1 my abs doesn't work while riding can u please figure out let me tell you about my abs when I bridge to the abs coupler it's start to show multiple errors on meter n abs lights flashes can feel pulsing in both lever but not with that much force. Secondly when I run my bike on center stand abs light start blinking means it is working but actually it doesn't work :-(

@nicholasmezes5043 Жыл бұрын

Where can I find that map??

@ludvigknoosfranzen2906 Жыл бұрын

Absolutely love it! Question though: I have a 2009 FZ1-SA (ABS) and the ABS computer sits on the inner right side behind the front fairing. So, would the DV8R front fairing fit the FZ1-SA model as well? Any experience, someone?

@liv4music Жыл бұрын

I love the look but I live in NH and ride until it snows so I'd be afraid I wouldn't have enough wind protection on those 28 degree mornings when I head off to work at 5:50 am.

@mikesrcgarage Жыл бұрын

Very smooth sounding exhaust note... I bet that bike rolls up on the pipe nicely! ✌️😎👍

@mikesrcgarage Жыл бұрын

Absolutely stunningly beautiful, a place teaming with abundant life which is how it should be. Funny how in such a remote and beautiful destination man still has the need to say "I was here" lol! Great video... Epic location!

@mikesrcgarage Жыл бұрын

Hey Patrick, I've been watching your videos on the Typhoon H which I just got yes very late in the game. I have been searching everywhere for info on expo/rate/curves for all four functions for I have changed all four and I'm not new to drones. Seems that you can increase the rate to 150% but I am very hesitant to do so not knowing how much is too much. I noticed after setting rate curves as mentioned the final output shows that the sticks are only moving to about 80% at full throw. I fly in manual mode which steps things up but I believe it's still a bit sluggish although it flies amazing! Do you have any info on just how far you can crank up the throws before it's a problem? I would think it could handle the full 150% but some flight controllers need a certain% as a buffer for motor differential to make controlling it possible. I really hope you see this for you so far are the only one that had any info on setting end points for expo/rate/curves. Thank you in advance for any input you may have! Have a great weekend! Mike.

@buelle109 Жыл бұрын

Mike, I have never pushed the rates up that high so I can only say you should do so in increments and test everything slowly. One thing to keep in mind is that the ST16 has been known to get oxidation on the stick potentiometers which can cause erratic behavior. One thing you want to check often is the Hardware monitor and make sure when you push a stick to it's limit the corresponding signal shows 100% of it's movement. If you get a bad stick reading anything done to rates will also be problematic. I have had to clean my sticks three times on my H Plus but never on my Typhoon. Good luck.

@mikesrcgarage Жыл бұрын

@@buelle109 Thank you so much for responding and your information I could see how that would present a problem did you use a spray to clean them? I have checked the monitor and all seems well but it does display some erratic behavior at time but only with gps on, in manual mode it flies amazing! Thanks again!

@atglennite01 9 ай бұрын

Hey Mike, I was curious if you adjusted your YAW as well. I noticed when I use left or right it seems like a very long time before it starts turning. Did you set the same values for yaw as for the right stick? I would like the “throttle/yaw” stick to be more responsive.

@mikesrcgarage 9 ай бұрын

@@atglennite01 Honestly I would have to check but I believe I did turn it up to match the others. Does it do that in rabbit mode as well? Honestly to me the only time it flies like a normal drone is in manual mode with gps off and some people have had flyaways doing that.

@atglennite01 9 ай бұрын

So far mine hasn’t had a fly away but I have heard horror stories about it. Yeah the yaw seems to lack responsiveness in all throttle speeds for me. I changed my settings this morning for the yaw. I’ll do a test later today when the rain stops.

@thedrone_explorer Жыл бұрын

Awesome video. 👏🏾👏🏾👏🏾 The into in itself was epic. And the video is very informative. I started flying this area with my anafi a few months ago and it is definitely a hidden paradise. So much to explore.

@hisense123456789 2 жыл бұрын

When did the new rotor come out ? I have a late 2013 at 17,000kms

@jeffspears8801 Жыл бұрын

2015

Ең жақсы KZfaq

Пікірлер