3:52 I don't know if you figured this out already but they come from the factory like that, it's for clearance.
@AdzeMartin27 күн бұрын
I bought this RXT1200 clutch for my GT500 5.8L 2013, but the slave cylinder doesnt work, it burst,, it’s a OEM new one, do I need a different one for this clutch?
@brianmiller5074Ай бұрын
Thanks for the great video. I have been driving my stock 2017 Mustang GT and the shifts from 2nd to 3rd are notchy. I heard this is a common issue with the Mustangs. Would this shifter help that specific issue? Thanks
@christopherthomas5972Ай бұрын
Doing one at work on a lift and was a pain getting enough room to get input shaft out. Gonna tilt the engine going back in thanks for the tips.
@lstnlne7399Ай бұрын
installed an Calimer mt-82d stage one on 2019 gt mustang aluminator 5.0L engine MMR pulse ring mgw spec 2 shifter mc leod rst which always had problems shifting into 1st. and reverse. After 10k would not go into reverse or 1st. gear. Sent transmission back to Ben and Dylan at Calimer. They claim McLeod rst wrecked transmission. I bought the SECOND Calimer mt-82d stage 2 cyro treated micro polish gears carbon fiber synchro rings billet forks and Mantic 9000. smooth as butter and rock solid. McLeod blame it on the 2017 to 2019 slave cylinder which I had a new one installed when I put the stage 1 in. F. McLeod RST CLUTCH cost me major bucks !
@ryanfreeman5987Ай бұрын
It would help if you show what they look like after install
@Rob_S197Ай бұрын
Hey man so if I wanna go white in front and in rear would u have a link for the white ones but for the rear ?? Thx
@vonlipichracing251Ай бұрын
Great video man! Helpful to see this before doing it.
@fernandom6192 ай бұрын
Have u got pull over yet?
@AlphaX13Ай бұрын
Don’t think these are a reason you’d get pulled over for.
@lstnlne73992 ай бұрын
maybe you need to spend 200 bucks on a better microphone lousy sound. mgw rocks 2019 gt mustang aluminator 5.0L engine calimer mt-82d stage 2 mgw shifter spec 2 boom trans mount mantic 9000 dds drive line vmp tune pedders coil overs w external canisters bmr k brace stop the hop rear braces by bmr fhp front strut brace bmr rear strut brace bmr and steeda completed suspension mods g force half shafts roush cold induction mangnaflow competention three inch exhaust dw-400 fuel pump cold case radiator fhp high output alternator odyssey amg battery autosport roll cage mmr pulse ring autosport roll cage sve rims 10ft 11r MCH pilot sport mishimoto radiator reserve fhp differential steeda differential brace mgw spec 2 is great watch their video on adjustment is a must 😊
@lstnlne73992 ай бұрын
boomba trans mount
@ChristopherGonzalez-uh1et3 ай бұрын
do i need to upgrade my clutch when putting in a new trans?
@Gwape_Jam2 ай бұрын
Upgrade? Not necessarily, if you are stock and replacing with stock trans. But you should replace it while you have the trans out, that’s all the labor right there. But upgrading is always a good idea, but you have to be careful and not go too crazy with a clutch and lose a bit of your daily drivability
@miguelestrada49653 ай бұрын
Are they road legal
@AlphaX13Ай бұрын
Don’t think these are a reason you’d get pulled over for.
@edgars5.03 ай бұрын
What headlight bulb do you have? It’s bright !
@itzlogic5514 ай бұрын
Does the borla over axle pipes bolt right up to the corsa axle back mufflers?
@coolali46494 ай бұрын
Do I have to change the hood if I want to change the front bumper? I got a 2012 5.0 btw.
@3mrx2994 ай бұрын
did u cut the grille to fit the horse emblem ? because there is a place to fit the snake how did u manage that ? (english is not my first language)
@1SloStang-Arxv4 ай бұрын
So these aren’t a direct replacement?
@hermanrogers13255 ай бұрын
The plug and play means the abs wheel and the studs should have been installed my doubt is about the exact power increase and you should put new bearing and seals
@omarmoran30975 ай бұрын
Any update on your car?
@AlphaX135 ай бұрын
Video will be coming out SHORTLY, small hiccups causing a bit of a delay.
@Bdr3026 ай бұрын
what wheel studs you used?
@celsobarbosa35956 ай бұрын
do you what color is for the reverse wire
@keeghanwarner65326 ай бұрын
Where did you get the bumper from?
@davidc66666 ай бұрын
That passenger side line on the hood is a mess
@ghettoluck1087 ай бұрын
what if i don’t use bracket i want to swap to a 2013 front bumper on my 2010 mustang
@AlphaX137 ай бұрын
Without the brackets to hold the bumper up it would sag too much and possibly drag on the ground while driving.
@marcus5ryan7 ай бұрын
Thanks tons for vid. I won’t be buying one. This was all I needed to see
@AlphaX137 ай бұрын
Glad I could help!
@jonnyjonnyyespapa80138 ай бұрын
Are those lights suppose to stay on at all times while driving at night?
@AlphaX138 ай бұрын
Yes, the side marker lights should be on whenever the head lights are on.
@fonzil59098 ай бұрын
did you guys installed a new flywheel?
@AlphaX138 ай бұрын
Yes the flywheel that came with the clutch kit was installed.
@fredocastillo69849 ай бұрын
How’s the transmission been treating you bro
@AlphaX139 ай бұрын
The car isn’t driven very often but from the amount I have driven it, I haven’t had any issues with the transmission other than my speedometer being off.
@phillynott79510 ай бұрын
I'm about to replace mine, what a process great video!🫵🏼
@AlphaX1310 ай бұрын
Good luck!
@edamnaf926510 ай бұрын
I have a Ben Calimer Stage 3 (I'm prepping for a whipple) and a Mantic 9000 Cerametallic twin disk clutch that I'm scared to put on. Come help me >.> (I'm in Orlando FL ;))
@AlphaX1310 ай бұрын
Orlando is a bit of a drive that’s for sure, but if you after any questions I’ll do my best to answer them!
@neilbarber10 ай бұрын
Those look great! Any idea if they are legal in the UK?
@AlphaX1310 ай бұрын
I’m not familiar with the laws in the UK, however, I don’t see a good reason why they wouldn’t be legal.
@mgray160910 ай бұрын
Please never do. “What’s up KZfaq” again. I was going to subscribe until I heard that.
@AlphaX1310 ай бұрын
Thank you for the feedback!
@mgray160910 ай бұрын
@@AlphaX13 was joking obviously still subscribed but please don’t lmao
@mwh8210810 ай бұрын
this car never ran again!
@AlphaX1310 ай бұрын
She's had her ups and downs, but I'll be posting a video shortly showing she's up and running!
@andrewlawson144410 ай бұрын
Very helpful thank you 🙏
@theawesomeguy999911 ай бұрын
Hey man if you don't mind me asking were those 6 ton jack stands all the way up? I've got some daytona 3 tons that only go up 16-7/8 inches high and I'm worried about having enough clearance to pull the trans
@AlphaX1311 ай бұрын
I believe I had them two notches from fully extended.
@theawesomeguy999911 ай бұрын
@@AlphaX13 Thanks for the response! Got the trans out, all the way up and had to shake the trans off the jack to clear the car
@cjcullar11 ай бұрын
Could I ask how you got the top 2 bolts out for the bell housing ?
@AlphaX1311 ай бұрын
For people with hands on the larger side, going from the top of the engine typically works pretty well. Otherwise you can lower the transmission slightly and use a very long extension and socket to reach those top bolts.
@cjcullar11 ай бұрын
@@AlphaX13 also how exactly did you get the 3rd starter bolt out ??? It’s been such a pain in my ass
@AlphaX1311 ай бұрын
@@cjcullar crushing your hand and saying a few swear words… or find someone with small enough hands to reach up there with a ratcheting wrench. For some of the bolts it might be easier to go through the side where the wheel is.
@texas5thgen2259 ай бұрын
if you remove or loosen the AC compressor, you can gain access easily with a long extension stretching between the motor mount and header to that top starter bolt. @@cjcullar
@neitzelm1 Жыл бұрын
I see some drilled holes on the flywheel -- did it come balanced or did you have to take it to a machine shop?
@AlphaX1311 ай бұрын
During the install process you shouldn’t have to do anything not mentioned in the video. What you see in the video is how the clutch comes, hope this helped.
@jakevanmaele3653 Жыл бұрын
where do you have your positive and negative wires going ?
@AlphaX1311 ай бұрын
In the video around 4 minutes in I point out which 2 wires to use for positive and negative.
@rafp4502 Жыл бұрын
What does the car have for exhaust other than the Corsa Eextreme’s? Stock headers? Cats or no cats? Thanks
@AlphaX1311 ай бұрын
I believe in that video he was running bbk long tubes, bbk mid x pipe (cats), borla over axles, and the unique corsa xtremes quad tips (black).
@johnshepard7630 Жыл бұрын
Anyone knows where to find replacement for those lights? FOr the 2013-14 Version. They are not the same as the years after. Or a higher powered version, perhaps a crystal clear one?
@shadaylacrooks8774 Жыл бұрын
Will this fit a 2010?
@AlphaX13 Жыл бұрын
Yes, a 2010 should follow the same steps.
@YellowFellow86 Жыл бұрын
So reinforced mt82 over tremec?
@AlphaX13 Жыл бұрын
I chose the built MT-82 for simplicity and cost reasons. The tremec does end up costing more after all of the additionals required to make it work on the mustang.
@kaylynemeline1154 Жыл бұрын
Promo-SM ☀️
@drednour01 Жыл бұрын
Great video. Interested in tricks or tips to get trans back together with the engine. Had the twin disk off 3x now and have since ordered steel alignment tool. We cannot seem to get past the first disk. However, the disks slide nicely on the input shaft. Seems like an inch apart is the closest we have gotten. Any tips would be greatly appreciated.
@kevinbustos77469 ай бұрын
U figure it out?
@drednour019 ай бұрын
The steel alignment tool made all the difference. The plastic tool would slip in and out as it should. But the steel tool wouldnt. Loosened everything up and used the steel tool. Everything went back together perfectly. Not the easiest job on jack stands but I will forever buy the steel alignment tool going forward.
@VikingParanormal Жыл бұрын
I have the same side markers and my rear ones match and they’re all white led instead of the red led in the rear
@lazaromartinez4780 Жыл бұрын
Horrible hood ..... 😅 I see that bad fitment from 2 miles away 😅. Change it for an oem
@AlphaX13 Жыл бұрын
Yeah, not a fan. Currently exploring other options.