Question: I bought a seal and bearing kit because mine was leaking gear oil....do I only have to do the seals on the bolts and the bearing from the beginning?....I don't know if I need to disassemble the whole thing....
@TheDIYDoc13 күн бұрын
@@zachschaefer3824 replace all seals anytime you’re dissembling the lower unit.
@zachschaefer382413 күн бұрын
@@TheDIYDoc I gotcha....I just wasn't sure if I had to tear the whole thing apart...no sense in doing that if I don't have too lol. But if I'm in for a penny, in for a pound, right? Lol
@TheDIYDoc13 күн бұрын
@@zachschaefer3824 you don’t have to tear the whole thing apart if gears are fine! You need to replace all the seals. So bearing housing oRings. Housing Seals. The driveshaft seals and O rings.
@zachschaefer382413 күн бұрын
@@TheDIYDoc Okay, I will focus on those. Thanks for the video and your help....I will post an update as it happens. THANKS AGAIN 😀👍
@TheDIYDoc13 күн бұрын
@@zachschaefer3824 shoot me a like and follow thanks man
@silasjahn717614 күн бұрын
Think for the video
@TheDIYDoc14 күн бұрын
@@silasjahn7176 thanks man. Give it a like and subscribe.
@AntonStudios199916 күн бұрын
Seriously thanks man for the tip I changed my sway bar links and every time I go over bumps or pot hols it sounds like my tire is gonna fall off BC of how loud it sounds I have changed almost everything lol except bushings,those damn bushings lol thank you very much for the help
@TheDIYDoc16 күн бұрын
@@AntonStudios1999 yeah man Give it a like and subscribe please
@kyleperrry19 күн бұрын
Thanks
@TheDIYDoc19 күн бұрын
@@kyleperrry ya man throw it a like and subscribe I’m always posting useful boat stuff.
@djreeves924920 күн бұрын
Great video. Where did you buy the long snap ring pliers? Thanks
@TheDIYDoc20 күн бұрын
@@djreeves9249 on Amazon man. It’s in the video
@MrBuddyMitch21 күн бұрын
Does the heat affect the rubber part of new seal that is installed ?
@JesusCampos-sh6sf23 күн бұрын
Hi, guys! My name's Jesus Campos, and I'm from Portugal. Where can I buy a new KIA OPTIMA 2014 rear stabilizer bar? This 2014 KIA car model is very rare in Portugal and I'm absolutely sure that I'm just gonna solve this problem buying it to a foreign country. Thank you so much in advance 🙏
@AntonStudios199916 күн бұрын
Amazon should have them put in your car details and itl show you ones for your car
@georgelollis739124 күн бұрын
This is a great/useful video.
@leveragelifestyle8581Ай бұрын
Great video. Just tested coils in 5 min and found the one I suspected was causing issues due to a old valve cover gasket issue and it sitting in oil for an extended period of time at some point. Now I'll grab 1 coil instead a whole set for no reason. Thanks!!
@picklefootАй бұрын
Thanks bro. I'm super glad you tested a new one
@picklefootАй бұрын
You know how long it takes ro so that😢😂
@paycelucas3355Ай бұрын
This same a a j60
@TheDIYDocАй бұрын
@@paycelucas3355 it’ll be similar. Not exact. 60hp gear mechanism slightly different and years make a difference. But overall same ish
@hsanguilyАй бұрын
Beautiful.
@TheDIYDocАй бұрын
@@hsanguily thanks!!!
@Mark-ew8lqАй бұрын
Cool! Great demonstration. Thank you, I'm needing a throttle cable so this helps show the action of shifting.
@buckeddyАй бұрын
1996 ocean runner 150, disconnected shifter rod one under carbs from cables and it is very hard to shift. I have the star adjuster out all the way so I can grab reverse but now no forward, any other way of adjusting other than new cables? Thanks again
@TheDIYDocАй бұрын
@@buckeddy depends. If shifter rod screws in you could adjust height of threads used.
@buckeddyАй бұрын
Nice work thank you sir. Helps
@parkerquigleypuffАй бұрын
No gloves is ballsy. must be your home. Most of those plunger stoppers are very easily removable which makes unclogging a lot easier. also most p traps (pipes under your sinks) are not glued together but only secured by a gasket and a nut, so you can unthread it from underneath to get much better access to where the clog most likely is. Good luck homeowners with your leaks.
@TheDIYDocАй бұрын
@@parkerquigleypuff I’m aware. But for people less capable than you or I this is a fast easy method and less likely to screw stuff up.
@octaviojabali6981Ай бұрын
Thank you best video on how to check coil simple and straight to the point
@TheDIYDocАй бұрын
@@octaviojabali6981 I still prefer redneck method just swap it to another cylinder if your miss moves it’s diagnosed.
@octaviojabali6981Ай бұрын
@@TheDIYDoc thank you just so your viewers know i hove a dodge promaster the boot sometimes breaks so what I do is replace the head of coil it separates and there is a long spring i elongated it and it works without removing the stuck boot that is if you’re not replacing spark plug 👍
@edgarq-yo1zhАй бұрын
So many videos about ignition coil diagnosing, some use devices that are expensive and i will not use again until another coil goes bad. But this video went straight to the point, helped find out the bad coil in a few minutes and got my car back to purring like a baby, thank you so much.
@cowgoesbaaАй бұрын
Or just use the wrench to jumper the wires together.
@TheDIYDocАй бұрын
@@cowgoesbaa you plan on holding it when you do ?
@robincornelius655Ай бұрын
It's better he went fishing than not go fishing.
@TheDIYDocАй бұрын
Right?
@robincornelius655Ай бұрын
He scooted off. 😂
@TheDIYDocАй бұрын
@@robincornelius655 my names Scott. Scott scooted
@TheMeisakuАй бұрын
Too funny!!
@TheDIYDocАй бұрын
Here for you
@metooo-zo6ddАй бұрын
This shit would never work
@TheDIYDocАй бұрын
@@metooo-zo6dd but why
@uplandnewbie2468Ай бұрын
I see what you did there 📝📝🫡
@joshuacyr5495Ай бұрын
How did I know there was a boat on that truck....oh yea...thats the only response
@TheDIYDocАй бұрын
😂
@jamessteelman3936Ай бұрын
Is that a fabuglass?🎉
@TheDIYDocАй бұрын
@@jamessteelman3936 1965 Larson all American. Check my other vids. I rebuilt her.
@TheDIYDocАй бұрын
The motor is off a 1976 fabuglass though!
@condellclarksr200Ай бұрын
Fishing trip here we come
@TheDIYDocАй бұрын
Salmon season.
@ericacsabon6113Ай бұрын
Well Im gonna miss her
@TheDIYDocАй бұрын
Are you
@mindlessamusement7095Ай бұрын
Lmao....this seems like a fair dispute resolution.....but the boat name....😂😂
@TheDIYDocАй бұрын
It was either that or “land hoe”
@andrebroussard6582Ай бұрын
We can do that?!?!
@TheDIYDocАй бұрын
@@andrebroussard6582 you can. But I’m divorced.
@RedneckBeachАй бұрын
Epic response my dude 😂
@charlesdahmital8095Ай бұрын
If you didn't see that one coming......
@jananabanana3180Ай бұрын
Gone fishing....😊❤
@zachpinnell6385Ай бұрын
Hahaha
@TherronCeortezMcgeeАй бұрын
A ski biat
@TheDIYDocАй бұрын
You have to peep the boat name though 💁🏻♂️🤷🏻♂️
@nedkent52392 ай бұрын
Very cool!
@TheDIYDoc2 ай бұрын
Thanks man. Shoot me a follow.
@tonyduong36392 ай бұрын
i checked all my 3 old four coils' output circuit for toyota sienna 2004, they showed nothing at all for output. BUT I didn't understand why my car still ran and idling smoothly. Any ideas?
@TheDIYDoc2 ай бұрын
Not checking resistance properly.
@skylerrose77182 ай бұрын
This go for a 1976 70 hr Johnson ?
@TheDIYDoc2 ай бұрын
It will be similar yes. Not exactly but pretty much the same steps
@surgeneral1082 ай бұрын
Good job, you helped us a lot 👏👏 ( I also changed my sway bar links and it didn't help )
@TheDIYDoc2 ай бұрын
Please shoot me a subscribe!
@jeffreyzondo75603 ай бұрын
Im checking my ignition coils. Kia rio. 4cylinder Output is 5.99 , 5.96 , 6.06 , 6.06. Are they fine or must i change
@TheDIYDoc3 ай бұрын
Idk the standard for your car but if they are all equal that’s reassuring and likely fine.
@picklefootАй бұрын
Good answer. No advice just posting vids
@1luxuryliner4403 ай бұрын
I do like your videos for sure
@TheDIYDoc3 ай бұрын
Thanks! Hopefully you’ve subscribed.
@1luxuryliner4403 ай бұрын
I was wrong earlier I checked
@1luxuryliner4403 ай бұрын
I am with bell alerts
@davep41733 ай бұрын
"i have replaced everything else". Same. Thats why I'm here. Sway bar bushings are last to tick off the list
@TheDIYDoc3 ай бұрын
If my video helps. Shoot me a subscribe
@BlueDreamz2524 күн бұрын
Same here. And realizing they are the cheapest thing I could have started with makes me feel crazier 😂
@TheDIYDoc24 күн бұрын
@@BlueDreamz25 mine ultimately ended up being a spindle nut on my strut. But hey. It’s a full new suspension now lol.
@ahmedfouad98473 ай бұрын
Is amazing no alot of body is talking and he dont know about this point i have missFire in all cylinder without any fault code on the scanner and i have alot of think after i saw your video i teat my ignition coil is give me 2.9 & 3.0 but the problem i dont know what is the standard range u can help me to know what the stander range or my vehicle 🫡