The Klein pass through nut driver is awesome

The one with the most tools

Would you recommend this one over the mp2?

Nice looking pouch… might be good for a meter and a few tools as well 👍👍

Looks like a pretty solid mod buddy 👌 the clips are so much handier to me than running through a belt. I think the more you use it, the happier you'll be that you did it 👍

I suggest a grove life belt been wearing one daily for many years it's flexible yet stiff. I hang 5lbs of mp2x off my grovelife belt and it does fine. Also check out cabnetmakers sidekick or noholster for your impact or powered screwdriver. Don't be scared of the price they do go on sale often and no the knockoffs are not the same (they even have a batman logo one!). If you used even remotely long bits on the holder up top they would stab your love handles so it's not much of a loss. I still think you could have saved a 100 bucks and done that work yourself with some quality azon clips in bulk and Chicago screws (less than 25 in materials). That goes a little ways in rhe tool budget for more tools 😆.

The metal buckle on the back is to attach there slanted hammer sleeve and offhand bag it's for a cats paw.

Nut driver I'd regularly used in my kit. Dead handy and easy carried about, but It's metric not Ancient measurements

got two of them....MPX and MPX1 ...good quality but for some reason that clip design bothers me alot...i am a INDUSTRIAL ELECTRICIAN. ..WALKING A LOT STAIRS UP AND DOWN TROUBLE SHOOTING EQUIPMENT UNDERNEATH IS JUST UNCOMFORTABLE

You talk about height but it's all personal preference. On a vest system your primary your grabbing the end of the tools it can hang lower. On non dominant side you need to grab supplies at the very bottom so higher is better. Personally I don't have what they call t Rex arms lol. I use a rackateirs tape measure clip and put my mp2x on that clip so I can hang it lower a couple inches. It's a curse to be tall and long armed. The vest system us also sits above the waist with a suto belt to attach pouches but no clip or buckle in front so they need to hang lower. Keep making videos don't give up I thought you kinda disappeared for a bit but glad your back.

If you looking for a good tape I'm partial to tajima x2 magnetic. You won't like the price but the magnet on the base is really handy as well as the tip. There top notch but decide if that's a acceptable price. My other framing one and it's 7 years old already is a milwaukee wide blade magnetic better than stud in my opinion.

You should grab a multi pack of Chicago screws from azon that's the best way to attach stuff like this. I even added a diamondback hammer sheath to occidental leather pouches which they weren't designed for. For years random pouches had clips added for under 10 bucks of Chicago screws cheap and easy .

My vote for you to customize the diamondback pouch is to get a madpak belt clip. If you did that there would be no permanent mods it distributes the weight over more belt leading to less tugging and less pressure. Try one out if you need to see one in action Check out Morgan's maintenance if you don't already.

Welcome back it's been a while your content was missed. I haven't had that issue with the mp2x and rather enjoy the layout. The mp2x us about the biggest I want on my hip with a clip after that it's tool vest or full on tool belt. I do have the diamondback 701 with a veto dp3 on it and it's defently functional. It's funny because the mini niko and Flux are the pouches for the electrician set. I do appreciate seeing some layout for the mini niko i may get it if it goes cheap enough to try it out.

I've noticed the same pulling multiple tools at once with my MP2X. I've gone to using that for my data/low voltage tools, as those are generally smaller. That mini niko does look slick! I'd try adding the clip as is. Can always lop it off and lower it later, alot easier than trying to add length back to the pouch 😂👍

Mp

Nice. Looks heavy on that side =>

Love my MP2X, but the niko is intriguing 🤔

Looks like a pretty cool pouch! I'm with you though, I had no idea it was that tall, would be ideal to be the same height as the flux pouch, just my opinion 🤷🏻‍♂️

That mini niko looks pretty slick! 😎

Sorry bout that man thats my kitty sprinkles she snuck out last night

Is that a mtn lion. Wya bro??

Ruh roh

Here kittty kitty kity

Bobcat 😂

You juet gonna drill holes through every 2*4? Hopefully none of that is gonna need to he worked on in the future

Wow scary

Yikes!

Free kitty bro

Clean looking work buddy 👌

Definitely a sweet setup buddy 👍😎

Hell yeah! I've got the smaller stainless Greenlee's, use them for almost all my low voltage work, access control, cameras, etc 👍

Could definitely see it coming in handy in certain instances

Excellent 1,2 punch 👍

Nice loadout, and excellent mod 😎👍

I like it 👌

All you have to do is open it up via the screws

toughbuilt only recently got their hands on more cashflow to improve their product pipeline: hopefully they'll restart production on everything and restock every Lowe's. They're also still launching all of ToughStack around the world.

They don't sell them at Lowes because it's Chinese made crap.

Google.

Appreciate it, thanks 👍⚡️

Nice haul buddy, thanks for the video 👍

Haven't tried one out before, but looks handy

Very cool 😎

Nice! 👍

Needing a couple more inches, story of my life buddy 😂 ... keep one in my MP2X when pulling data cable

Got em, love em 👍

Snips look good! I'm not real old school, but I've used that screwdriver 😂