Man you scared me jajajaja

You're humor is my humor. Nice build and entertaining video

With your background in pre-cast concrete, would you please make a "Rocket Stove" using high heat portland cement and a 5 or 10 gallon bucket (10 is better than 5 right?). Anything with a "High Heat" label seems to cost a lot, so if you would make the mistakes for me/the world you will definitely have my attention.

I watched this twice now. Another great video………. And HaxMan is looking fit!!!!

YT hitting on that ad placement lmao. "FINALLY, AFTER MY (BIG NUBER) SEARCH. I FOUND IT.C Cuts to the screen anddddd Ad. 🤣

I happen to have a dozen bags of cement left over from a work project.. i think i know where they're going now..

You gained another subscriber instantly! This was an awesome DIY build!!

Too funny!

It’s too bad that when it’s all done, unless you’re standing up you won’t be able to see the fire or coal base plus it always has to be full to work properly. Now just figure out how to put some windows in it. 😂

I love making mistakes. That way nobody thinks I am a God of anything. Better to have people not think of you as talented or you will be at their house building a fire pit because, either you wife said you would or because, a guilt trip.

Gas contains 1% Cancer causing BENZENE... So don't be sniffing it. Your video is bogus, take a look at your genny's Kilowatt output using propane. I have no problems running ethanol gas in my generator, I test run my Predator for 5-10 minutes every couple of weeks. I have two 5 gallon cans for the Genny that have had the same gas in them for over a year. It works fine. The problem is carbs with floats can get gummed up if they sit with ANY gas in them for long periods of time. You have to pop the bowls off of them and shoot carb cleaner in the jets. Also car engines nowadays last TWICE as long as they did 25 years ago. Alcohol is a RACING FUEL. My first lawnmower engine that my Grandpa gave me wouldn't run cause the carb was all gunked up. I learned how to clean the bowl and jet, that was 60 years ago. Retired Refinery Engineer.

I recognize that background tune @13:00 from WLS. Haha 👍

DIY if you have a giant metal workshop... Lol

Hahaha at first when you pulled out the calculator I thought aww man this is way above my level. But by the time you got to the tape and ratchet straps I knew I was in the right place. Hahaha I'm only half way through and have already learned a lot. 🤔😅😊

"Y'all better redneckorize!" I don't watch enough of your videos, but I'm going to fix that, haha. Great video man. Very inspiring.

Like a boss! After a brief underwear check.

Like a boss! Great job! What’s the name of those green rolling shelves you have in the back of your workshop?

unless you've used concrete rated for stoves or fireplaces that pit is a danger to any person near it when a fire is in it

Loving the vids, you know my man there are several mathematical shortcuts you could've used to save on materials, still super awesome design!!

😂 thanks man this was great. First video of yours I’ve seen. Subscribed. 👍🏼

LMAO on wutter section...awesome vid Haxman!!!

I wonder if you could have used one of those big, scary, paper cutters to square up the carpet tiles?

You lost me at Pi.

How well has the metal held up from rust? Looking to do this but curious if pre-painted roofing panels are a better choice, or if the galvanized is sufficent?

You are truly a craftsman. That mistake in the round table could have destroyed that project but you found a way to recover and finish it. You got street cred points as far as I’m concerned. Keep creating!

I lik e the wuestion the science part. Freeze dry fauci next

Listen to the Wheely cooing at the Beautiful Aubsome Riders !!! I'd like to be there to be held up by these Gorgeous Ladies. O imagine yaw'll are tiring out some aftrr each ride but yaw'll ate really fit , dont smoke, no pircongs, no tatoos, just Classy & A Refresh to Wath on these videos !!! Your hips are all just fine, have fun yaw'll . . . 👍😎🤟👉❤️🫶🌹🥰😀🌟👈🇺🇲🙏 DDH 5-28-2024.

Is it possible to build it in the ground if u ran the side vent tubing upwards around the outside?

Put in a foot switch on that radial arm saw

Where can we get the hex lights?

😂 inner chimpanzee 🐒 💩

when he said, 'i did that backwards' i laughed. lol

Good video , great information and best Dad. I did things like this with my kids too and it pays off. I like the square tube and when I try I’ll look into square tube for plant ports . Peace Always 🙏

This video was so funny that i subscribed to your channel. Thank you for making garage organization my entertainment for the day!

At 14:00 you mention the possibility of putting a 2-by-4 behind the post. I recommend you do (and attach it all to the wall), better safe than sorry.

Girls pin your hair back when using anything that rotates.😊

Gah! I hate the sound of foam and plastic rubbing together. Grates on the ears! Neat build!

Those radial arms are beasts!!

Love the idea. Would love to see it done in a bedroom closet.

I had to fire up one of my synthesizers to play the little bit at the end of the video lol

Great job guys!

Looks awesome! What should this roughly cost for materials?

Absolutely love this idea. Thinking about doing it soon but adding furniture feet to keep them from slamming into each other!

Yes, please!

The random Bigfoot made me a believer

I’m looking at getting a kit from them but how can I put the flag at half-staff , when occasions arise, if there is no pulley system.

Mud mixer just be spending a ton on marketing right now with influencers. I’ve been seeing it everywhere. Looks cool but for most people it’s hard to justify spending 3500 bucks on it.

Transmitter is the opposite of receiver

Concrete bursts when it gets very hot. Not every time but often and unpredictably. It’s from the chemically bound water separating and turning to steam. Are you worried about this?