thanks! im gonna try this on my feet!!

Great video! I was able to remove the interior trim pieces without removing the 2nd row seat. Also, at the 14 minute mark, after removing the clip on top, using PB Blaster, and lots of hammering, the pin still wouldn't budge. For those who are struggling with removing the pin, just remove the two 12mm bolts that secure the hinge to the sliding door and remove the entire hinge/door trolley from the track. This was a lot easier than trying to hammer out the pin. Thanks again! Hopefully this repair will last awhile!

You the man!

Great instructional video. Covers several things I didnt even think of.

Does it have to be fresh?

hi , just wanted to say, the directions were spot on !. you saved me $1400 by doing it myself. it was easy with your help. thanks again , Paul P.😉

Almost always when I remove the side panel that covers the sliding door track, the bracket that the panel screws in to at the front of the panel comes off. This is a small piece that is tack welded to the top of the track, and the welds routinely rust out. A little bit of JB Weld will hold it back in place.

OH MY GOD THANK YOU !!

Thank you🎉🎉🎉

Absolutely amazing video thanks Pal even though I’m an Autobody Tech it was so very helpful to do it right the first time and also save time ! Thanks !

Might not be the best idea, but I fixed it by tossing a bolt that fit in there lol

Amazing details demonstrated, especially the final spooling of the cable. Hope I will be able to get it done without any issue by following you instructions. Thank you.

You didn't get the rest out, are you kidding me😅

Thank you! Just changed a faulty alternator and your instructions were spot on.

What you don't see it's the nearly impossible to reach wiring harness bolted to the original alternator that makes it a nightmare to get out.

Thanks for this very helpful video. My door is opening but only manually. How can I know if the problem is the cable or the motor?

That piece just failed on my stepson 2010 Acura TSX, now it’s 11pm and parts stores are closed and amazon is a 2 days out on shipping. For mean while I had a handful of them plastic push buttons that hold your plastics/ fender liners together, I just took some dykes and snip the plastic down short and boom it’s holding it down so the brake lights don’t constantly stay on.. fits perfectly in the bracket hole 🕳️ thanks for the vid

You are a godsend, my friend!

Thank you for your video! I truly appreciate the step by step instruction explaining every detail. A $20 part and accomplishment feels so much better than spending over a $1000 for someone else to do it. Thank you so much!

Great Video! We sell a much easier solution! If you provide us with an email we would love to send you some more information and potentially send you a sample to try!

Really helpful man🎉🎉🎉

Thank you

It has worked for me right up until the end where the door needs to be reset from the control right after a battery disconnect. Tore it all apart and while the cables were off i noticed the motor would run until one way or the other consistent with the door opening and closing. Put it all back together this time opening the door and waiting for the motor to stop, then disabled the door. Put it back together with the same problem. The door will not respond to the controls after a reset. Put it in drive and it beeps so it knows the door is out of calibration. At this point i am stuck.

Thanks buddy. Much appreciated!

I hope a pro wouldn't clean a battery like that. I take a shop vac, suck up any loose corrosion after removing the cables, take the battery out, submerge the battery terminals in the baking soda/water solution in a plastic container then use a rag dipped in baking soda/water solution to clean the top of the battery. You're inviting problems just pouring the solution over the battery while it's still in the vehicle.

I would never let my engine bay stay that dirty good fix though.

This is an awesome instruction video. Thank you!

Great video! Got my alternator replaced today in like 1hr 40mins. Saved a lot. 👊🏼

Gracias muy bien explicado

How do you fix aircoñdtion

Just did mine, saved me a lot of $$. I was having a hard time getting the c clip on the slider, decided to remove the two bolts which was much easier. ** if you doing the passenger side, front cable goes to the back of spool and back cable to the front.

Thank you for the video! I can’t find the link to buy the cable. Can you post it here or tell me how to find it? Thank you!!

A lot of slurry was created by the baking soda and water mix and it overflowed the battery tray a bit. I rinsed with fresh water inside the engine compartment area that it dripped into. Is this an issue?

I don’t know what I did wrong, but after fixing my door, my dvd player and the button for the trunk no longer work 🥴

Now how do you get this thing back in?

What if you cannot open the sliding door to begin with? Where do I start in that case?

The first thing I thought you'd do when you removed the airbox was to cover the open throttle body, to prevent anything from falling into it. I would also recommend that you brush and blow off, or vacuum off, the valve cover prior to removing any of the spark plug coils, again, to prevent any debris from falling into the spark plug wells. And, as you commented, it's also a good time to clean the throttle body, and the MAF sensor.

Can I use this for a 2010 odyssey?

Thank you so much. This was very helpful. I was away from my van and family member got a flat in it. Your video explained to them how to reach the tire and jack.

Anyone making a machine that beats the dirt out like this. I hate the pos kinder gentler agitator washers now.

Best video ever

Is it also the same for a P1174 code? My 2012 Honda Odyssey EX has this code when I run OBD but there is no Engine Light. Could you please suggest if your solution works for P1174 as well?

thx

You are the man! Incredibly thankful for this video. I replaced the passenger side, and like a commenter below I discovered that on the passenger side the cables are wound around the spool in the opposite direction (the front cable winds around the back of the spool). Enormous headaches on the passenger side due to a massive air-handling unit that blocks the rear cable exit. I couldn't figure out how to remove it completely. I was able to loosen the unit enough to work around it and only lost one bolt to the void in the process.

Thank you!

Would this be the same by change for the 2018?

Honda odyssey 2012 serpentine belt

Thanks for the video. This is my second time replacing this cable. Seems like they last about 5 years or so. The tip about winding the spool when the door is fully open is fantastic.

Is this a 2.5L 4cyl Frontier?

Ours broke twice Honda quality isn't what it used to be. I'm shocked by all the dirt behind that panel.