In eleven years since this was posted, I'm hard pressed to find a more useful video for figuring out hooking up the linkages after having the carburetor off. You are much appreciated. I'm grateful this video finally showed up for me.
@SugrshaneКүн бұрын
Thank u sir. Took awhile to find a video that shows how the automatic choke linkage worked. I’m not a fan of the crank me wide open set up either. Common sence knows better than that !! Thank u again
@dgriffin6074Күн бұрын
Nicely done. Thanks. Your video has obviously helped lots of mower owners.
@techguy90232 күн бұрын
I got a new carb. The plastic part with the priming bulb doesn’t suck up any gas. What should I look at? It came with a new one (large black plastic part that levers go through). It’s clean. It had an insert that snapped through the hole that mounts to the carb that the original didn’t have so I removed it. It isn’t in your video either so it must have been for shipping.
@jeffodorico89972 күн бұрын
what model throttle did you install?
@janstokreef63583 күн бұрын
Where can i get the cap? I am from the Netherlands. Can you buy it on Amazon?
@JoeyBuildsGoKarts4 күн бұрын
I have a 127cc Briggs & Stratton engine on my GoKart just recently bought the same clutch but newer. It fit the rotator but the rotator doesn't have a hole to screw in to tighten it down and I'm noticing even with the old clutch and the new one it would just slide off the rotator since nothing is actually keeping it in place what can I do to prevent it from sliding off the rotator?
@dimitar4y4 күн бұрын
Note, basic fittings are only good to 10 bar, "Maybe more". Pneumatic fittings, if genuinely certified, are made of softer material so when they fail, they fail 'slow' instead of turning to shrapnel, and hydraulic rated fittings, if genuinely rated, are the correct ones to use for this application.
@beegekhaos31714 күн бұрын
This is exactly what i was looking for, explained very clearly and easy to understand. Thank you so much!
@garthholman98965 күн бұрын
Very good video. I knew I had a fuel problem and you showed me how to remove the carburetor and clean it. The job was reasonably easy and the mower works well. I like my mower with a Briggs & Stratton engine better than the previous Honda powered mowers that I had - they both developed surging issues. After doing the work the mower started and ran well on the first pull of the rope. Now, I wonder how I can get it to run with a quieter exhaust.
@tejay94165 күн бұрын
How do you take apart the Walbro carb that's got a weird bottom with a plug coming out the bottom for a wire. Gives no indication as to how to loosen
@sys25 күн бұрын
love it! been battling a rebuild of an engine today .. and got exactly that and couldnt figure it out .. opened the engine and checked everything and it still did the same .. this explains it a bit better =) Thanks! =)
@michaelkistner15535 күн бұрын
I have bent my throttle linkage. Can I send you a picture?
@ronmueller30745 күн бұрын
Thanks. You've been very helpful.
@ronmueller30745 күн бұрын
A 3/8 socket over the shaft to the C clip & a hammer will persuade the Clip to seat.
@angtxsun44605 күн бұрын
Was given one of these trimmers- 8+ years old- a clean up, tune up, replace fuel lines could not get to run smooth- this car adjust into sure helped, thank you for sharing your expertise!
@C94J6 күн бұрын
Would this cause the fuel to dump out and on top of the muffler on a Kawasaki v twin?? My mower gets hot and then shuts off and it wont start again. Then fuel just starts dumping out like its flooded.
@sureshs57706 күн бұрын
Price
@intelboydj17 күн бұрын
Bright arc temp 12000K (60Hz)
@lewiemcneely91438 күн бұрын
I got 40 feet of 3/8ths non marring off of Ebay and finally found a reel for it. 4k# rated. Gave it away last week. Blessings!
@aubril80228 күн бұрын
Thank you so much had no issue putting my new car on Howe er forgot where the small coil wore went. Being blind I didn't seethe other hole at first. Thanks so very much!!!
@Pete.Ty18 күн бұрын
👍👍👍.Thank you
@robertmailhos81598 күн бұрын
I've been there did that on my pressure washer hose
@bobgrob48 күн бұрын
nice that Rustoleum mentioned you can spray at any angle, even upside down. The 36 dollar can of paint I bought has to be held vertically. Thanks for the demo.
@mkens66249 күн бұрын
Thanks for these videos. I just bought a pug f570 with the 18 hp version of this...
@isiahdonovandailycarrepair48199 күн бұрын
Hey I was wondering if u know if a quantum b&s mower had a cast iron flywheel magnets stick to the thing so I’m guessing it id
@tjblaketb10 күн бұрын
I have a mint 2009 john deere zero trun with a 22 or 23 twin engine when I bought it from a friend he was using start fluid to crank it cable had moved and choke plate was not closing set it where it close now cranks fine but idles high😮
@goirish659010 күн бұрын
I just rebuilt one of these carbs and hooked the linkages back up. Mowers running great at full throttle but is suddenly surging a bit at idle. Could it be an issue w the linkages. Again only happening at idle and needle jet is clear.
@davidschwartz512710 күн бұрын
Carburetor cleaner is very harmful to your liver! Wear rubber gloves when working with it.
@jasonkidney583711 күн бұрын
Did that man draw a penis?!
@psepolishsteamengines202112 күн бұрын
nice
@graeme174413 күн бұрын
Who thinks they are better than what's made today.
@jason632514 күн бұрын
I guess I'm a decent mechanic. I have a gravely zero turn. It's very hard to start after i run it a long time and turn it off. I just ordered 2 new plugs, 2 new coils and the fuel sylnoid shut off just incase. Because it lets out a small pop when i turn it off.
@vladix75014 күн бұрын
Hi, thanks for great video. I have 12hp briggs mower tractor. It has only choke adjuster lever but does not have engine rpm adjusting lever. Engine revs to maximum all the time. Is there a way to fit some sort engine speed lever like john Deere tractors have?
@Pete.Ty114 күн бұрын
👍👍👍. Thanks
@jefferykirby93415 күн бұрын
HOW DO YOU HOOK UP THE ATTACHED TO THE COVER LINKAGE?
@rjh245915 күн бұрын
Thanks for the video
@Thomas-nz4uh15 күн бұрын
Can you get 10,000 or higher rpm's with this techometer?
@ja447615 күн бұрын
I'm wondering, if the small /weak spring isn't there, what is it going to do ?!!
@jeremydavidson255315 күн бұрын
Ive got a john deere d105 with a briggs 17.5hp and it is surging bad. Any chance you can send me link for more in depth video on governor adjustment?
@patrickmiller297216 күн бұрын
Vary helpful of the linkage in your video
@linfung429716 күн бұрын
he is right
@user-sx3ng2dq6f17 күн бұрын
Nice ! I repair my aluminum skiff with the same welder and rods . It’s. Cheaper than paying someone else .
@user-sx3ng2dq6f17 күн бұрын
It’s 3/16 bottom plate . I repair the crack and put a plate over .
@messengeronbeats-m.o.b.410617 күн бұрын
i have a 2006 model #13an77tg766 troy bilt pony the extension to the right on the deck looking at the video did you modify that one i missing mines what is the proper spring and can i go to the holes on the bracket that holds the deck in place with the arms in hole with pin
@JanWestra-mq6xv17 күн бұрын
MAY BE YOU CAN HELP ME , i HAVE A DAMAGED PUSH VAVE. MODEL 289707 TYPE 0154-01 CODE 9411224D .hOLLAND MY NAME J.WESTRA
@alexalexx975317 күн бұрын
Ma interesează un motor
@darrellsomers542718 күн бұрын
Got a part # on those guides and who makes them ?
@Mike-su8si18 күн бұрын
So i can't use that engine properly take off the troy bilt bronco mower and look for another engine keep that one for a parts engine then cause i do have 2 others that are just fine with no piston ring problems All those intek engines from 12.5 and up to 18.5 are the same engines. So now im gonna need another engine once i take that one off and just either fix its bad ring or use it for parts
@Mike-su8si18 күн бұрын
I think mines piston rings are bad or one is. Cause i done my head gasket and it fixed it from pouring burnt oil smoke out but still pours is and on and off
@jasonneely959618 күн бұрын
Thanks for showing that I had a quick question. My pony toy belt keeps over revving. Can I use a larger throttle rod for that that’s longer because my smaller screen broke for the throttle return I ordered a bunch of springs and rods, but they’re not the right size am I able to adjust it myself?