Just ran across your video! Thanks for the great tutorial. I had already determined myself to DIY it and your video made me very confident. Now I'm just waiting on the rebuild kit to arrive. I read through comments as well and I believe I'll heed the advice of others and go ahead and change lines out as well. And probably install a filter before the bulb.
@kevinspathelf94714 күн бұрын
I just did the wear ring on mine now I have water pouring into the hull through the one little hole with the o rings on the left while sitting and it sprays in with force like the pumps pushing it when running and floods it? What did I do wrong and what is that hole for?.. 99 seadoo spx 787
@bennett215 күн бұрын
The other videos I found for this gear box repair were missing the removal steps. Thank you for your detailed video!
@duncanbecher49866 күн бұрын
How is it running, where is the fuel coming from for it to run
@LonnieJohnson16 күн бұрын
From the gas tank
@bigsnow17056 күн бұрын
Very simple to follow along video. I’ll still call for service to fix mine lol. However 2 summers in a row my carburetor has clogged up and I’m using ethanol free gas. What do you think is the issue?
@LonnieJohnson16 күн бұрын
Cheap gas. You need to run 93 octane
@halamkajohn7 күн бұрын
is there an additional sensor that hooks up to the single terminal.? I dont have an answer. so it maybe sits open , then gets tiny positive from distributor , then grounds coil, then opens? I made a 2 transistor board for a 50 cc AMF moped. buy 1 find out.
@LonnieJohnson16 күн бұрын
You ground by mounting it and then hook up the wire.
@drufreeman59067 күн бұрын
Getting ready to do this on my 2003 Focus with the 2.3L because I have that same code. Replaced the solenoids but they didn’t fix the problem so I’m pretty sure it’s the actuator based on everything I’ve seen and the slight hesitation at low rpm. Otherwise the car has run pretty solid despite this issue. Can’t wait to have my low end power back tho. Thank you for the very instructional video and keeping it simple. I feel I can do this work now on my next days off without worrying about it as much. Having the mental picture of what to do helps me so much. So thank you again for making this video!! You da man!
@LonnieJohnson16 күн бұрын
Your welcome
@andrewpearson34127 күн бұрын
Nice informative video! My dad gave me a Poulan Pro saw that "only needs the fuel line replaced..." to be in working order... It's been a good saw, but has been well used on our farm. The small engine shop charges super high rates to fix anything and they take forever to do it. So I'm going to give it a shot myself. Your video seems to be just what the doctor ordered. I hope it works. Thanks.
@LonnieJohnson16 күн бұрын
Thanks and your welcome
@SylvainFluet8 күн бұрын
Hi from Québec , Canada ! Great tutorial , thank you so much for your help , I need to do the same on my Mercury 90 ELPTO (2006). Your video convinced me to do it myself !
@LonnieJohnson16 күн бұрын
Thanks and your welcome. It looks intimidating but its not that bad. Glad to help.
@SmashixMetal4Evah8 күн бұрын
Thanks Lonnie, I just used this to replace the door and ice funnel on my 17 year old fridge.
@LonnieJohnson16 күн бұрын
Your welcome
@brandonmccall392910 күн бұрын
Whats the part number on the bearings
@LonnieJohnson16 күн бұрын
BEARING (32X58X13) 09262-32023 You can find it on Amazon
@LonnieJohnson16 күн бұрын
Here is a link to parts you might need. www.ronniesmailorder.com/oemparts/a/suz/50d0b166f870022c2c536450/rear-suspension-arm
@michaelfarris255610 күн бұрын
Another fine one
@LonnieJohnson16 күн бұрын
Thanks!
@TheHazelberg10 күн бұрын
Hi Lonnie, i think you provider me here with the solution to my problem. I already changed the Control module in the dash, filled up the freon, checked all fuses and switch, and all are just fine. Just clutch won’t engage on compressor. Now I will check out this low Freon pressure sensor. Thanks a lot 😎👍
@LonnieJohnson16 күн бұрын
Your welcome
@TheHazelberg10 күн бұрын
Hi Lonnie, i think you provider me here with the solution to my problem. I already changed the Control module in the dash, filled up the freon, checked all fuses and switch, and all are just fine. Just clutch won’t engage on compressor. Now I will check out this low Freon pressure sensor. Thanks a lot 😎👍
@TheHazelberg10 күн бұрын
Forgot to mention that I did the test from switch to compressor by bypassing the switch. And the clutch engages then. So.. that traject is fine aswell.
@familyfuntime105611 күн бұрын
Thanks for this video! I did this but now my power steering doesn’t work?! Did I mess something up turning the steering without the mower running?
@LonnieJohnson111 күн бұрын
Your welcome and No you shouldn't have, the steering is separate from the deck belt. Look and check all the connections related to the power steering.
@shadjohnsen814311 күн бұрын
The bow-tie clip at the 1:24 mark is what I've been looking for all day. I could not figure out how it was supposed to attach. Who knew it would use just one hole, on one side instead of the groove on the other side too. Seems like an incomplete design, but if it works it works.
@LonnieJohnson111 күн бұрын
It works but can be a headache.
@mattmcdonald361512 күн бұрын
Man trying to see if i can just tape the wire after the motor caught fire
@LonnieJohnson112 күн бұрын
Black electrical tape should work.
@nayefalkurahi335713 күн бұрын
hey my 2005 seadoo 3d makes a horribke sound when i rev it? like dqueling / brake noise ?? i just replaced the wear ring and filled the cone with 80-90w gear oil.. Prop spins freely.. idk what it could be ?
@LonnieJohnson112 күн бұрын
Where is the sound coming from that you hear? In the back from the pump or from under the seat at the motor.
@nayefalkurahi335712 күн бұрын
@@LonnieJohnson1 hard to tell but seems like from the motor?
Check the drive shaft bearing to see if it needs greased or replaced.
@nayefalkurahi335710 күн бұрын
@@LonnieJohnson1 it looks like it was filled with white lithium, I'll fill it up and see if it goes away..
@DavidGonzalez-pi5hj16 күн бұрын
Excellent video!!! Very clear, very well explained, very easy to understand, thank you so much!!!👍👍👍
@LonnieJohnson112 күн бұрын
Thanks and your welcome
@mikezags081617 күн бұрын
do you think this would be similar in the JX75? where did you purchase the igniter?
@LonnieJohnson117 күн бұрын
Amazon
@LonnieJohnson117 күн бұрын
And yes, I just looked at the JX75 and it looks like the same motor.
@nicholasbourgeois613118 күн бұрын
At the beginning of ur video what is that other plug for
@LonnieJohnson118 күн бұрын
Not sure. Its always been there. Probably for another factory option that wasn't ordered with this SUV.
@TheHazelberg10 күн бұрын
Yes mine has also that plug hanging right there. I always asked myself where it is for. But now I saw it here on yours too. So I don’t think about it anymore.
@nicholasbourgeois613110 күн бұрын
It must not be that important my 2001 doesn't have it really just wish I could get my electric fans to come on
@LonnieJohnson16 күн бұрын
Hook it up straight to the battery to see if it works. If it works it could be a fuse or the sensor. If it don't work it could be a bad fan.
@allenredfearn43818 күн бұрын
Excellent video. Exactly what I needed.
@LonnieJohnson118 күн бұрын
Cool! thanks.
@fredroe755618 күн бұрын
What does that acuator arm hook too its a little white part???
@LonnieJohnson118 күн бұрын
Watch the video at 7:26
@fredroe755618 күн бұрын
@LonnieJohnson1 do you know if that little white ball thing can be purchased? Mine is broken and I'm having no luck around here.
@LonnieJohnson118 күн бұрын
You should be able too. Take the broken part off and take it to an Auto Zone or parts store to match it up.
@fredroe755617 күн бұрын
@LonnieJohnson1 I went to ford dealership yesterday they told me part is obsolete
@LonnieJohnson117 күн бұрын
I would ask what the part is called and try to find an after market part. You can also call around at junk yards to see if they have a vehicle in the their yard like yours and see if it still has the motor in it.
@user-gd2lb5zf5p18 күн бұрын
I've 3 Honda motors, 2 weed eaters and 1 for extensions. All 3 don't stop spinning even without pressing to use. All are under 1 year.
@LonnieJohnson118 күн бұрын
Does the cutting head turn freely when the motor is off?
@user-gd2lb5zf5p18 күн бұрын
@@LonnieJohnson1 it does
@LonnieJohnson118 күн бұрын
Then it could be your idle is too high and needs to be adjusted down lower.
@user-gd2lb5zf5p17 күн бұрын
@@LonnieJohnson1 ok thanks, I will check it today and let you know
@robertwest309319 күн бұрын
You took the fear out of this job for me. Thank you! I was expecting to have to drive the bearings off the whole length of the shaft.
@LonnieJohnson118 күн бұрын
Your welcome
@landen_57621 күн бұрын
i’m getting gas to the fuel pump but not to the carb it had good pressure but it won’t go into the carb
@LonnieJohnson120 күн бұрын
Have you checked your solenoid on the carb.
@CrushingGames21 күн бұрын
Fantastic video!! One of the best! Great Woody the Woodpecker! 🤩
@LonnieJohnson120 күн бұрын
Thanks
@Mel-lp9yz21 күн бұрын
Thank you!!!!
@LonnieJohnson120 күн бұрын
Your welcome
@philorton194022 күн бұрын
Thanks for video. Have the same problem and this helped much!
@LonnieJohnson120 күн бұрын
Your welcome
@user-lh6gg5tl3t23 күн бұрын
We sell Medium Lift Blade that may fit your equipment. We're happy to offer you the product completely free of charge in exchange for a video review. Let me know if you are interested.
@LonnieJohnson120 күн бұрын
I have an Ex-mark with a 52" cut
@user-lh6gg5tl3t20 күн бұрын
@@LonnieJohnson1 How can we contact you?
@user-lh6gg5tl3t20 күн бұрын
@@LonnieJohnson1 🥳
@LonnieJohnson118 күн бұрын
You want to give me a set of blades if I review and advertise your product.
@user-lh6gg5tl3t16 күн бұрын
@@LonnieJohnson1 Yes.That's right.
@claudesulpizi578723 күн бұрын
Thanks very helpful tips! Doing this same job in a couple of days! Just waiting on the gasket.
@LonnieJohnson120 күн бұрын
Your welcome
@tcaldwell577224 күн бұрын
Is there an edger attachment for this model
@LonnieJohnson124 күн бұрын
Not sure, but I don't think it spins fast enough to be an edger.
@andyzdrums27525 күн бұрын
Great video, would this be the exact the same procedure for my 2017 x584? Thanks!
@LonnieJohnson124 күн бұрын
Thanks! It should be close if not the same.
@davidpeterson58025 күн бұрын
Finally, this how to video correctly shows how to replace the cable. Luckily I ran across your video before I broke my lawn mower even further. Thanks.
@LonnieJohnson124 күн бұрын
Your welcome
@dadlills437225 күн бұрын
Hey Lonnie I know this an old video but I just tackled my trailboss 330. Couldn't have done it without you. 👌. Turns out the ring clip came off the reverse gear. A very talented mechanic/welder I know made sure that it would never happen again lol. My question is did you replace the triple lip seals on the shafts. Mine look fine but my bud is just change it. Over 100 bucks for the two ughhh. I'm ready to seal it up but holding off now he's got me second guessing lol.
@LonnieJohnson124 күн бұрын
No, not at that price. It should be find if it doesn't look damaged, and if your doing the job yourself you don't have to pay for the cost of labor.
@mckennavandolah74528 күн бұрын
Can I get pics or video of all the vacuum and fuel lines? Mine were completely off all lying in a bag when I got my quad and I can’t find anything how they go….
@LonnieJohnson124 күн бұрын
If you start looking at 0:10 you will see the vacuum lines at the top and the gas line is a separate line below those.
@mckennavandolah74521 күн бұрын
@@LonnieJohnson1 mine aren’t hooked up at all…also my choke is unplugged and I can’t find where I plug it into…
@LonnieJohnson120 күн бұрын
Wow! someone left you a real puzzle. I don't have it any more however, what state are you in. Just wondering how close you are, it's easier to look at it and fix it.
@mckennavandolah74513 күн бұрын
@@LonnieJohnson1 I’m in Oregon. I think I have most of it figured out. I can’t find the choke connector from quad to the connector on the electric choke thoufh
@jackswink75929 күн бұрын
Excellent, I mean Excellent video!! Put back together, water works but ice lever doesnt work now. Any answers? I figured it out, I put the sleeve in backwards. Great video!
@LonnieJohnson124 күн бұрын
Thanks and thanks.
@allenhughes12Ай бұрын
I have the exact same problem and your video makes me feel a little better about life in general. Thanks for the helpful tips.
@LonnieJohnson124 күн бұрын
Your welcome
@michaelcholodny3869Ай бұрын
How do I lock the pully my belt jumped broke my fan my pully just spins I can't get the bolt off
@LonnieJohnson124 күн бұрын
Put the belt around the pulley and squeeze it tight and use an impact if you have one, if not you should be able to get it loose with a ratchet and socket.
@daddyrabbit835Ай бұрын
It looks like it works much better than C-clamp
@LonnieJohnson124 күн бұрын
I does work better.
@cook6052Ай бұрын
Love the concise and sefficient KZfaq...you are All-Pro sir!
@LonnieJohnson124 күн бұрын
Thanks!
@beckiecobos5843Ай бұрын
Thank you so much! This is precisely what I was needing, verbatim. You made it look so easy. Thanks again. Be blessed.❤
@LonnieJohnson124 күн бұрын
Your welcome
@MrFlatlandcycleАй бұрын
Thank you for a direct, no nonsense explanation. I wonder if I could leave the lights unplugged? I don't mow at night. Hmm.
@LonnieJohnson124 күн бұрын
Your welcome, and yes you can leave the lights disconnected just put the wire where they can't get damaged.
@jagco2594Ай бұрын
Thanks for posting this.
@LonnieJohnson124 күн бұрын
Your welcome
@MacarioArguetaАй бұрын
It would only take 30 seconds more to show how to level the deck from front to back of the deck, also the front of the deck is supposed to be 1/4" lower than the back of the deck. Good video however you really only showed how to level side to side, and not the complete deck leveling .Have the job. and there you go folks have a nice day
@LonnieJohnson124 күн бұрын
This video is to show where and how to level the deck side to side not front to back because that is an easier step for another video for those who would like to see it done.
@jesusramos-my2qrАй бұрын
Thanks man i got a denso pump ready to install but the original since 1997 it refuses go die
@LonnieJohnson124 күн бұрын
It will sooner or later.
@stevetodd306Ай бұрын
I just replaced mine. Easy job. Instead of prying inlet bracket off of old unit, I used a drill bit in the middle whole. A few twist of the bit separated the two parts.
@LonnieJohnson124 күн бұрын
Cool, thanks for the info.
@OksiwaluxАй бұрын
we want to invite you to review the latest taillight for chevy suburban tahoe, how to contact you?