I did. Not sure if the video shows it or not, but I have been using this printer since this upgrade and the TFT works perfectly.

@@asadjibran was just saying you didnt tell them to do this nor did you show it !!

Yes I did! Unfortunately it's probably not great, but it did work out well for me, so you could try it out and see how it works for you. I was able to find a spool holder that I really liked: www.printables.com/model/65651-universal-filament-spool-holder I then build a small thing to mount it to the Genius, similar to the one in the video above. That mounting object has a slot where you can use a threaded rod that locks into place. On the open end of the rod you can mount the universal spool holder. Here's the mounting I made: www.dropbox.com/s/h1yviu46wh36ret/Genius%20Custom%20Spool%20Holder.3mf?dl=0 It worked very well for me. Infact, I had to add some foam between the mount and the spool holder to add some friction, as otherwise it would spin freely and end up unspooling a lot of filament while printing! :) Hope this helps you out as well! PS: There's a newer version of the universal spool holder which you can use as well: www.printables.com/model/66440-universal-filament-spool-holder-gen-2

Thanks for flagging. Unfortunately the original mount I used is no longer available on Thingiverse. Here's an alternative: www.thingiverse.com/thing:3716043/files

Thanks for flagging. Unfortunately the original mount I used is no longer available on Thingiverse. Here's an alternative: www.thingiverse.com/thing:3716043/files

3duk.co.uk/index.php?action=downloads;sa=view;down=19

I've been a PrusaSlicer user since I started. While Cura is pretty good, I find that PrusaSlicer profiles for the Genius work better for me.

@@asadjibranplease, would you pass me a profile prusaslicer with nozzle 0.8

@@GiuseppeLepore Wish I could help, but I changed my laptop a few months ago and don't have the 0.8mm profile anymore. I found that 0.6mm was a much better compromise b/w speed of printing and quality and I've been using that for the past couple of months.

@@GiuseppeLepore To add to my last answer, I started with the built in 0.4mm profile for the Genius (Prusa Slicer comes with it now) and tweaked it to work with 0.8mm nozzle size.

I'm not a 100% certain, so it's better if you look at the wiring diagram of the 3D Touch and make sure it's the same as the wiring diagram for the BL Touch. But I have seen some sites say that the 2 are compatible. If not, then you'll need to make some slight modifications to the firmware to work with the different wiring scheme.

Okay thanks imma look around my probe is not going out

can i use different tft fw? it i must pair the tft and the board fw

Yes. The TFT firmware is different from the main board one and you can use a number of different ones. I chose rawr because I liked that feature set, but you can use others and it will work.

Thank you. I'm happy you found the video helpful. I don't fully remember as it's been a few months, but I think the mount prints with no supports, standing up. I did have to use glue stick on the print bed to make sure it stuck to the bed, as it has a very small contact surface with the print bed. If you do need to print with supports, you can use the paint on supports feature in PrusaSlicer (help.prusa3d.com/en/article/paint-on-supports) to stop supports from being generated in places where you won't be able to remove them. Another quick hack I use is the "supports only on build surface" setting, which usually generates supports that I want. You should play around with the paint on supports and the supports only on the build surface setting to figure out what works best.

Glad you liked it!

Hi. Sorry about the broken link. It's fixed in the description now. You can get the firmware for the TFT from github.com/wgcv/RAWR-TFT-Firmware-Artillery3D/releases.

@@asadjibran Thanks man 👍

Thank you! Happy to hear my video was helpful.

Hi. Thanks for your comment. Yes, it's possible to fix the VTX cables and use Beta Flight to control the channels and other VTX parameters. I have another video on that which you can view at kzfaq.info/get/bejne/mrl3fpB23NzMYH0.html. Hope that helps.

Probably. If it flies but has no video, the flight controller is most likely OK. You should start by checking the connections between the camera and the FC and from the FC to the VTX just to be sure a cable did not break. This video from Joshua Bardwell should be very helpful: kzfaq.info/get/bejne/j5qJnNd60MiRfmw.html It's possible the FC has issues as well, but only in it's video system, in which case you can attach the camera directly to the VTX. This means you will loose OSD but at least your quad will be flying.

The sound is a bit bad at the introduction, but is pretty good after the first few minutes, when we start with the actual installation. I'm working on getting better equipment for recording though so hopefully soon my videos won't have audio issues, even for a small segment.

Thanks. Good audio is something I still struggle with but understand how important it is, even more than video quality. Always trying to make it better. Big nozzles are just so much convenient for the right prints. I moved from a 0.8 to 0.6mm nozzle on this printer and have been very happy with the results. The prints finish faster, and quality doesn't suffer as much as it does with a 0.8mm nozzle.

@@asadjibran definitely seeing that quality suffering on some of my prints with 1mm. LMAO! But I do have some "blocky" stuff that there is no detail...yeah bud. 1mm zips through those . LOL

@@nicholaswillcox True. seeing the filament just fly off the roll with an 0.8mm is a bit scary. :)

Yes. I'm using Octoprint as well. The BL Touch functionality depends on the G-code your slicer generates. If you've setup your slicer to do auto bed leveling before printing, it will work as expected. Octoprint only forwards the commands your slicer software decides, it doesn't do any pre-processing on those commands (by default, plugins are a different case).

@@asadjibran Thank you for the explanation

Thank you! I use PrusaSlicer 2.3.1, and they have built in profiles for an Artillery Genius with a BL Touch. So that works for me. I created a Gist with the start and end gcode, so you can copy from there if needed. gist.github.com/theonejb/70becb351508719b5411bb604258b621

@@asadjibran If I use M420 S1 without Z3, does it load the saved z offset by default ?

@@aidan2235 The M420 command only enables or disabled the mesh bed leveling. It does not effect the z-offset. You set the z-offset using the touchscreen once during initial calibration. The Z3 in the M420 command sets the fade height. The bed level correction is gradually reduced over the fade height, and then the bed level correction is disabled once the fade height is reached in the print. You can find some more info about the fade height if you're interested at marlinfw.org/docs/configuration/configuration.html#leveling-fade-height

@@asadjibran thank you for the replies

Thank you for the kind words. And thank you for that awesome tip! I have a spray of cleaning alcohol next to the printers at all times, and I'll try it out the next time I need to unglue something. Thank!

Glad it was helpful!

I have not read the details about how it works, but if you're interested you can read the paper at: www.sciencedirect.com/science/article/pii/S0141635921000726?via%3Dihub

Happy to be of help. 😊

Happy to hear this video helped! Personally I didn't tighten then too much, because they only hold the dampeners so in place, and the fc just sits between the dampers. In the video what I was trying to convey was that you shouldn't tighten them too much, since that works squish the dampeners. Hope that helps.

Fico contente em ajudar!

Glad I could help. I agree, I need to improve my editing and video making skills quite a bit. But I'm just getting started and hope to get better with time! This is the first Eachine product I have, so can't comment on their QC. However, luckily I was able to get Smart Audio working on this by connecting one additional wire b/w the FC & VTX. That's in the next video I just uploaded.