To jest koszmarny sen! Dobrze, że nie kupiłem tej drukarki.

I had the same exact problem and I. was not even able to do a successful print at all. It happened during testing. and it happened about three times every single time had to take everything apart to get it out. And then the last time I put everything back together and then it says the hot end was not working. I ended up sending it back to Amazon because I was not dealing with that ordered another one and then the one that I have right now I have not had not one issue

You should check their website, they probably have instructions for both clearing the filament as well as how to properly change filament which will probably prevent the problem from happening. You might find that you're doing something slightly wrong that's actually the cause.

Hello How did you make it operative?

Did the jam happen while printing, or while unloading filament? The later one was a quite often fault at the Qidi X-Max 3 and is a simple config error. The filament unload happens to fast. The filament is still weak when the gears grap the part wich former was in the meltzone. So it gets sqeezed and deformed, than tangles between the extruders gears. The solution was extremly simple: In the printer.cfg is the macro for filament unload (on the X-Max 3 "unload" was misspelled "unlaod", so first I missed finding th macro). This macro basicly retracts the filament for 80 mm with fast retraction. I copied this line, changed the first line to 20mm. The following line I changed to 60mm and a feedrate a third from the original value. Now the filament still unloads fast from the hotzone, but much slower in the coldzone. The filament does not get sqeezed by the gears anymore. Since I did the change, no problems with stuck filament anymore. This printer might simply have the same issue, as the hardware is mostly the same...

Bonjour, déjà une dizaine de jours que j'ai cette imprimante. Bonne analyse de la qidi q1 pro qui pour un prix tres correct. Effectivement le défaut est le porte bobine maigs il y à tres longtemps que j'ai abandonné ce système. J'ai toujours installé des séchoirs. Cordialement

This better be covered under waranty

Damm bro that socks. I have bad news too, I can't even buy a Q1 pro from Qidi Tech because they don't accept prepaid credit cards and I had to spend the money I had saved up, so I guess that I will never be able to get one 😢😢😢

Hi Will, I am having the same issue as you, after only two days!!! First day was okay, I had few good prints, but then second day nothing. Not even in manual mode I cannot purge. I will try to contact Qidi. Please let me know if you got it fixed. (And yes, I did cut flush the filament. I even tried running the filament directly to the hot end, not through PTFE tube). Thanks.

Thank you Will , I'm still trying to save up enough money to buy this printer, i have 300 dollars saved up now but it is going to take me a while before I have enough money to buy it. I'm disabled and can't work anymore, i just hope Qidi Tech doesn't raise the price before i get the money. Please make more Qidi Tech Q1 pro videos hopefully on printable modifications for this printer and Thank you for your help

What is the highest temperature filament you can print with this printer?

Great review. I have the same printer and really like it so far. I love that I can throw pretty much any material at it. I've printed TPU; the only trick there is you have to slow down the printer and the acceleration.

So glad that me and you both got this printer. It’s the best printer I’ve ever used it prints ASA like a champ I haven’t ever had use adhesive with it. I still do just cause I like it, but not necessary by any means.

i just one print after that clogged right a way i hate like this my Bambu A1 i dont have any problem

yes my problem to is like that is new why like that

so would you say the problems are now fixed? and that this printer is a worthy purchase? thx for the videos about the printer

I believe that concaved part below the screen is the door handle. I am currently trying to save up enough money to buy this printer as my first 3d printer

is this extruder a new version that clogs less or just a replacement for the old one that is the same design?

Do you know as to why the Q1 Pro would have a failure to boot issue? Constantly, I try to boot it up and it displays a message that "the start up is abnormal". Then prompting me to turn the 3D printer off, wait a while, and back on again. However, this doesn't work. I even tried it by turning it off, unplug the 3D printer and turning it on again after plugging it in. Again, not working. I just got it yesterday and it only was on for one session to print the included Benchy. I used the filament that came with the 3D printer. Nonetheless, today it decided to become a glorified paperweight. Currently, I'm waiting on a response from Qidi, but I do wonder, due to yourself having more experience, what your educated opinion might be on what I'm currently dealing with.

Mines clogged numerous times, I just take the two screws off the extruder and remove jammed filament… it’s definitely annoying

the Q1 Pro likes it best when filament ends are flush cut, yes it contradicts the past experience of tip-shaping filament. Sorry to critique, I think you were frustrated with the situation, it may have clouded your judgement. It clearly showed in the manner you assessed the situation and the remedies you pursued. I recommend to consult QIDI Wiki guide for further issues.

Do you have the STL file? and size of Carbon Filter you used?

what calibration did you do?

The user manual is missing step 2: "take the huge bag off of the printer" and step 5 or 6 (removing something from underneath the print bed)was not applicable to my new unit. The unit froze during firmware update and cant successfully check online autonatically yet, but hopefully in the future they will fix this. The printer also does not work with Cura slicer (yet?).... I asked their support and they said Cura was not for fast printing machines, whatever that means... Hopefully i can get Cura working with this!!

Just got mine today and it might just be me but the back of the build plate looks just a little bit higher then the front. it feels like the build plate does not fit in the frame properly.

How's the auto bed leveling / Z offset treating you so far?

Remember if you like the video don't forget to hit the like button it helps others find it and the KZfaq algorithm. Thanks again